adafruit tft lcd screen for sale

We stock a huge variety of displays for every project and microcontroller, including LCDs, TFTs, OLEDs, Paper displays and more. We also stock adapters and accessories for your traditional HDMI displays.

Low-power options are a popular choice for makers. Our ePaper, OLED and TFT products offer crisp detail which can be powered by your microcontroller without the need for a separate power supply.

Want some retro appeal to your project? Check out our Nokia 5110 LCD display, or our range of classic 16x2 and 20x4 LCDs which come in a variety of colours.

LCD Display Modules└ LEDs, LCDs & Display Modules└ Electronic Components & Semiconductors└ Electrical Equipment & Supplies└ Business & IndustrialAll CategoriesAntiquesArtBabyBooks & MagazinesBusiness & IndustrialCameras & PhotoCell Phones & AccessoriesClothing, Shoes & AccessoriesCoins & Paper MoneyCollectiblesComputers/Tablets & NetworkingConsumer ElectronicsCraftsDolls & BearsMovies & TVEntertainment MemorabiliaGift Cards & CouponsHealth & BeautyHome & GardenJewelry & WatchesMusicMusical Instruments & GearPet SuppliesPottery & GlassReal EstateSpecialty ServicesSporting GoodsSports Mem, Cards & Fan ShopStampsTickets & ExperiencesToys & HobbiesTravelVideo Games & ConsolesEverything Else

Add some jazz & pizazz to your project with a colour touchscreen LCD. This TFT display is 2.4" diagonal with a bright (4 white-LED) backlight and it"s colourful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display.

If you need a larger touchscreen, check out our 2.8" diagonal or 3.5" diagonal TFT breakouts. For a smaller display, see our non-touch 2.2" or 1.8" or 1.44" diagonal TFTs

In addition, 4 pins are required for the touch screen (2 digital, 2 analog) or you can purchase and use our resistive touchscreen controller (not included) to use I2C or SPI.

The screen is 1.77" diagonal, with 160 x 128 pixel resolution. The TFT library interfaces with the screen"s controller through SPI when using the TFT library. Refer to the screen"s data sheet for complete details.

The Arduino TFT library extends the Adafruit GFX, and Adafruit ST7735 libraries that it is based on. The GFX library is responsible for the drawing routines, while the ST7735 library is specific to the screen on the Arduino screen. The Arduino specific additions were designed to work as similarly to the Processing API as possible.

The TFT library relies on the SPI library, which must be included in any sketch that uses the scree. If you wish to use the SD card, you need to include the SD library as well.

With four bright white LED backlight and 240 x 320 pixels with individual RGB pixel control, this colour 2.8in. TFT display features a resistive touchscreen for fingertip detection across the entire screen surface. The workload is lifted from the microcontroller by a built-in controller equipped with RAM buffering, and the display board has two modes: 8-bit and SPI.

This 4.3" TFT screen has lots of pixels, 480x272 to be exact, an LED backlight and a resistive touchscreen overlay. Its great for when you need a lot of space for graphics or a user interface. These screens are commonly seen in consumer electronics, such as miniature TV"s, GPS"s, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24 bit color capability. It comes with HX8257A controller and optional 4-wire resistive touch panel screen which can be easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, and ARM. FPC with ZIF connector is easy to assemble or remove.

3.5" TFT LCD touch screen graphic display with 320 x 480 px resolution and 18-bit colour depth. It works with both 3.3 V and 5 V. Additionally, there is a micro SD memory card reader on the board.

The screen is based on the HXD8357D controller, it has a built-in RAM memory, so the microcontroller is not loaded with the display control. The device can communicate in two modes: 8-bit and through the SPI bus. For 8-bit mode eight digital data lines and four control lines must be connected. SPI requires only five transmission lines, but is slower than 8-bit communication. In addition, four additional pins are required to operate the touch screen.

The device can work in two modes: 8-bit communication and SPI, SPI outputs are shown in the table below. Details of 8-bit connection can be found in the tutorial.An example of a touch screen connection is available inthe user guide.

/* ADAFRUIT TFT: 2.2" 18-bit color TFT LCD display with microSD card breakout - ILI9340. Arduino Leonardo The ILI9341 chip is backward compatible with the ILI9340 chip, which is no longer used.*/

If you have a problem with any of the Adafruit_ILI9341 library examples, quote the example name. Explain your problem. Copy-paste your constructor statement.

Thanks for the response. Yes, I will but two points. The first is I have to get it to work before I do that; my pinouts might well be all wrong, although you don"t seem to think so? (I appreciate that I would just be soldering the header to the TFT though) The second is I er don"t actually have a soldering Ron. Any ideas for the best one to get would be welcome.

The Adafruit 2.2"" TFT screen is a small breakout board equipped with a colorful and bright display that can be used with many type of microcontroller thanks to its SPI interface. The board"s voltage regulator let you connect the breakout board to a 3 V or 5 V controller.

Canada Robotix is your source for Raspberry Pi, Arduino, Adafruit, SparkFun, Pololu, and alot more. We are here to make your DIY electronics and robotics project possible. We Love Robotics!

Add some jazz & pizzazz to your project with a color touchscreen LCD. This TFT display is 2.4″ diagonal with a bright (4 white-LED) backlight and it"s colorful! 240×320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128×64 display.

If you need a larger touchscreen, check out the 2.8″ diagonal or 3.5″ diagonal TFT breakouts. For a smaller display, see our non-touch 2.2″ or 1.8″ or 1.44″ diagonal TFTs

In addition, 4 pins are required for the touch screen (2 digital, 2 analog) or you can purchase and use our resistive touchscreen controller (not included) to use I2C or SPI.

Of course, we wouldn"t just leave you with a datasheet and a “good luck!”. For 8-bit interface fans we"ve written a full open source graphics library that can draw pixels, lines, rectangles, circles, text, and more. For SPI users, we have a library as well, its separate from the 8-bit library since both versions are heavily optimized. For resistive touch, we also have a touch screen library that detects x, y and z (pressure) and example code to demonstrate all of it. Check out our tutorial for wiring diagrams, schematics, and a walkthough on this display.