2.2 inch tft display suppliers pricelist

The NMLCD-220Q33is color active matrix liquid crystal display with light emission diode(LED) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.

It is transflective type display operating in the normally white mode. This TFT-LCD has 2.2 inch diagonally measured active display area with (320*RGB*320) resolution. Each pixel is divded into red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.

Shenzhen SLS Industrial Co.,ltd established in 2003, is a professional LCD module manufacturer and solution provider. We have 1 full-auto COG assembly line, 2 semi-auto assembly line, backlight assembly line, no dust TP bonding line and manufacturing tech support, we can provide unique, innovative and cost effective LCD module development and manufacturing. Our product range includes: middle-small size TFT LCD, industrial capacitive touch panel... Our LCD products have been widely used in communications, GPS, Equipment, electronic audio-visual, instrumentation, household appliances, PDA and other industries.

Shenzhen Newman Technology Co., Ltd. established in 2003, is a professional LCD module manufacturer and solution provider. We have two units full-auto COG assembly line, two units semi-auto assembly line, backlight assembly line, clean room TP bonding line. We can provide unique, innovative and cost effective LCD module development and manufacturing. Our product range includes: TFT LCD, intelligent display, special strip display, industrial capacitive touch panel, OLED display... Our LCD products have been widely used in communications, GPS, industrial equipment, electronic audio-visual, household appliances, PDA and other industries.

Keyestudio Circular TFT LCD is a 1.6-inch TFT liquid crystal display module. Its input voltage is 3.3V~-5.5V. It can display colored patterns and text.

micro-controller, starter kit, robot, shield, sensor, display, modules, etc. for Arduino, Raspberry PI, Micro:bit. We can produce for OEM or ODM orders. We also supply for many foreign trade companies. Our factory is located in Shenzhen, welcome to visit our production process.

We are one of the professional and experienced suppliers of tm022hdh35 tianma 2.2inch lcd display new and original, offering you the quotation and the price list consultation. Welcome to wholesale the high-end, quality and low price products in stock with us. Good after-sale service and fast delivery are available.

Samsung Galaxy M33 5G flaunts a 6.6 inch TFT display featuring a pixel density of 400ppi along with 1080 x 2408 pixels screen resolution. The bezel-less front screen of the device is equipped with a capacitive touchscreen and also features an aspect ratio of 20:9 besides a refresh rate of 120Hz.

On the backside, Samsung Galaxy M33 5G is equipped with a Quad-camera setup. It is composed of a 50MP f/1.8 Wide Angle Primary Camera, a 5MP f/2.2 Ultra-Wide Angle Camera, a 2MP f/2.4 Macro Camera and a 2MP f/2.4 Depth Camera. Autofocus, Digital Zoom, HDR mode and Auto Flash are a few main features available within. There is an 8MP f/2.2 Wide Angle Primary Camera present on the front side with Screen Flash for self-portraits and video calls.

The DT022BTFT uses the same connections as the DT022CTFT, with the exception of the backlight (which has connections shown in the Displaytech datasheet).

The provided display driver example code is designed to work with Microchip, however it is generic enough to work with other micro-controllers. The code includes display reset sequence, initialization and example PutPixel() function. Keep the default values for all registers in the ILI9341, unless changed by the example code provided.

Note that the WR pin becomes the D/CX signal in serial mode. CS is used to initiate a data transfer by pulling it low. At the end of the data transfer, pull the CS pin high to complete the transaction. The timing diagram indicates that you can pull the CS pin high in between the command byte and data bytes within a transfer, but it is unlikely needed if the display is the only device on the SPI bus. To keep things simple, we suggest to leave it low during the entire transaction.