lcd panel failure symptoms in stock

Performance issues may occur if there is any type of damage that is caused to the display cables or the LCD screen. LCD screen may show that symptoms like LCD screen stops working, work intermittently, color mismatch, flickering, display horizontal or vertical lines if there is damage to the display cables or the LCD screen.

If the issue persists on the external monitor, it may be an issue with the video card (GPU) or video settings and not the laptop LCD panel. Go to verify display or video issues in Windows Safe Mode. Otherwise, go to the next step.

Performance issues may occur if there is any damage to the LCD screen. The display may stop working, work intermittently, flicker, display horizontal or vertical lines, and so on, if there is damage to the display screen.

Dell laptops have integrated diagnostic tools that can determine if the screen abnormality is an inherent problem with the LCD screen of the Dell laptop or with the video card (GPU) and computer settings.

When you notice screen abnormalities like flickering, distortion, clarity issues, fuzzy or blurry images, horizontal or vertical lines, color fade, running a diagnostic test on the LCD helps identify if the issue is with the LCD panel.

Press and hold the D key and turn on the computer to enter the LCD built-in self-test (BIST) mode. Continue to hold the D key until you see the entire screen change colors.

If you do not detect any screen abnormalities in the integrated self-test mode, the LCD panel of the laptop is functioning properly. Go to the Update the video card (GPU) driver, monitor driver, and BIOS section.

If you notice any abnormalities in the LCD built-in self-test mode, contact Dell Technical Support to learn more about repair options that are available in your region.

Display settings like brightness, refresh rate, resolution, and power management may affect the performance of the LCD screen on your Dell laptop. Changing or adjusting the display settings can help resolve several types of video issues.

If the diagnostic tests on the LCD panel and the video card (GPU) passed, it is most definitely an issue that is related to software that is installed on the computer. If the above troubleshooting steps did not resolve the issue, you may try to restore the computer to factory default settings as a last resort.

Recently, the LCD screen started to show some artifacts, like flickering, screen freeze in dark image and corner starts to get brighter. Most of the flickering happens in a horizontal pattern (horizontal lines, parts)

Searching in the web, I concluded this could be a screen inverter failure, but I have no idea if another piece of hardware could be responsible of this.

Performance issues may occur if there is any type of damage that is caused to the display cables or the LCD screen. LCD screen may show that symptoms like LCD screen stops working, work intermittently, color mismatch, flickering, display horizontal or vertical lines if there is damage to the display cables or the LCD screen.

Some TV displays, such as LCD screens, use a backlight to illuminate the picture. If the backlight burns out or stops working, it will result in a blank TV screen.

Troubleshooting CRTs versus LCDs begins with similar steps, but diverges due to the differing natures of the two display types. The first troubleshooting steps are similar for either display type: power down the system and display and then power them back up; make sure the power cable is connected and that the outlet has power; verify that the signal cable is connected firmly to both video adapter and display and that there are no bent pins; verify that the video adapter is configured properly for the display; try the problem display on a known-good system, or try a known-good display on the problem system; and so on. Once you"ve tried the "obvious" troubleshooting steps, if the problem persists, the next step you take depends on the type of display. The following sections cover basic troubleshooting for CRTs and LCDs.

Catastrophic CRT failure is imminent. The noises are caused by high-voltage arcing, and the smell is caused by burning insulation. Unplug the CRT from the wall before it catches fire, literally.

If your LCD displays no image at all and you are certain that it is receiving power and video signal, first adjust the brightness and contrast settings to higher values. If that doesn"t work, turn off the system and LCD, disconnect the LCD signal cable from the computer, and turn on the LCD by itself. It should display some sort of initialization screen, if only perhaps a "No video signal" message. If nothing lights up and no message is displayed, contact technical support for your LCD manufacturer. If your LCD supports multiple inputs, you may need to press a button to cycle through the inputs and set it to the correct one.

Unlike CRTs, where increasing the refresh rate always reduces flicker, LCDs have an optimal refresh rate that may be lower than the highest refresh rate supported. For example, a 17" LCD operating in analog mode may support 60 Hz and 75 Hz refresh. Although it sounds counterintuitive to anyone whose experience has been with CRTs, reducing the refresh rate from 75 Hz to 60 Hz may improve image stability. Check the manual to determine the optimum refresh rate for your LCD, and set your video adapter to use that rate.

First, try setting the optimal refresh rate as described above. If that doesn"t solve the problem and you are using an analog interface, there are several possible causes, most of which are due to poor synchronization between the video adapter clock and the display clock, or to phase problems. If your LCD has an auto-adjust, auto-setup, or auto-synchronize option, try using that first. If not, try adjusting the phase and/or clock settings manually until you have a usable image. If you are using an extension or longer than standard video cable, try connecting the standard video cable that was supplied with the display. Long analog video cables exacerbate sync problems. Also, if you are using a KVM switch, particularly a manual model, try instead connecting the LCD directly to the video adapter. Many LCDs are difficult or impossible to synchronize if you use a KVM switch. If you are unable to achieve proper synchronization, try connecting the LCD to a different computer. If you are unable to achieve synchronization on the second computer, the LCD may be defective. Finally, note that some models of video adapter simply don"t function well with some models of LCD.

Not all analog video cards synchronize perfectly with flat panels. The gray Shutdown screen exaggerates the problem, so don"t worry if very tiny movements are visible after you"ve adjusted clock and phase as well as possible. After you"ve set the clock and phase controls for the best image possible on the gray screen, cancel Shutdown and the image should be optimized.

Your video card is supplying a video signal at a bandwidth that is above or below the ability of your LCD to display. Reset your video parameters to be within the range supported by the LCD. If necessary, temporarily connect a different display or start Windows in Safe Mode and choose standard VGA in order to change video settings.

This occurs when you run an LCD at other than its native resolution. For example, if you have a 19" LCD with native 1280x1024 resolution but have your display adapter set to 1024x768, your LCD attempts to display those 1024x768 pixels at full screen size, which physically corresponds to 1280x1024 pixels. The pixel extrapolation needed to fill the screen with the smaller image results in artifacts such as blocky or poorly rendered text, jaggy lines, and so on. Either set your video adapter to display the native resolution of the LCD, or set your LCD to display the lower-resolution image without stretching the display (a feature sometimes referred to as display expansion), so that pixels are displayed 1:1, which results in the lower resolution using less than the entire screen.

This is a characteristic of LCDs, particularly older and inexpensive models, caused by defective pixels. Manufacturers set a threshold number below which they consider a display acceptable. That number varies with the manufacturer, the model, and the size of the display, but is typically in the range of 5 to 10 pixels. (Better LCDs nowadays usually have zero dead pixels.) Nothing can be done to fix defective pixels. Manufacturers will not replace LCDs under warranty unless the number of defective pixels exceeds the threshold number.

Some people claim that leaving the unit powered off for a day or two will "erase" a persistent after-image. Others suggest leaving a neutral gray screen (like the one used for phase adjustment) up on the screen to "equalize" the display. I dunno. FWIW, I"ve seen this problem on older Samsung panels but never on the Sony or NEC/LaCie panels I use.

Again, this is a characteristic of LCDs, particularly older and inexpensive models. The after-image occurs when the display has had the same image in one place for a long time. The after-image may persist even after you turn the display off.

Transistor-based pixels in an LCD respond more slowly than the phosphors in a CRT. The least-expensive LCDs exhibit this problem even with slow image movement, as when you drag a window. Better LCDs handle moderately fast image movement without ghosting, but exhibit the problem on fast-motion video. The best LCDs handle even fast-motion video and 3D gaming very well. The only solution to this problem is to upgrade to an LCD with faster response time.

1Case 6-Abnormal Display. Bad components in power section of t-con.Case 7-Noise. Solder defect or shorted components on t-con.Case 8-Abnormal Display. Bad components in power section of t-con.Case 9-Noise. Solder defect or shorted components on t-con.Case 10-Abnormal Display. Bad components in power section of t-con.Case 11-Abnormal Display. Bad components in power section of t-con.Case 12-Noise. Bad solder connections, shorted or open components on t-con.Case 13-Noise. Bad solder connections, shorted or open components on t-con.Case 14-No display and back lights are lit. T-con Fuse Open or Bad components in power section of t-con. No voltage to t-con from main board or power supply(main board or power supply failure).Case 15-No back light. Inverter failure or power supply failure.Case 16-Dim back light. Inverter failure.Case 17-Dim back light. Inverter failure.Case 18-Dim back light. Inverter failure.

2Case 19-Uneven display. cell defect.Case 20-Uneven display. cell defect.Case 21-Damage from applied pressure to panel. Bad panelCase 22-Crosstalk. cell defect.Case 23-Crosstalk. cell defect.Case 24-Panel cracked.Case 25-Vertical block. Failed driver IC, TCP/COF failed ACF bonding to panel bad connectionfrom driver IC to TCP/COF.Case 26-Vertical line. Failed driver IC, TCP/COF failed ACF bonding to panel, bad connectionfrom driver IC to TCP/COF.Case 27-Vertical block. Failed driver IC, TCP/COF failed ACF bonding to panel, bad connectionfrom driver IC to TCP/COF.Case 28-Vertical block. Failed driver IC, TCP/COF failed ACF bonding to panel, bad connectionfrom driver IC to TCP/COF.Case 29-Horizontal block. Failed driver IC, TCP/COF failed ACF bonding to panel, bad connectionfrom driver IC to TCP/COF.Case 30-Horizontal block. Failed driver IC, TCP/COF failed ACF bonding to panel, bad connectionfrom driver IC to TCP/COF.Case 31-Horizontal line. Driver IC abnormal output. Failed driver IC, TCP/COF failed ACF bonding topanel, bad connection from driver IC to TCP/COF.

3Case 32-Horizontal block. Failed driver IC, TCP/COF failed ACF bonding to panel bad connectionfrom driver IC to TCP/COF.Case 33-Horizontal block. Failed driver IC, TCP/COF failed ACF bonding to panel bad connectionfrom driver IC to TCP/COF.

COF= Chip on film/flexTCP= Tape carrier packageIC= Integrated circuitT-con= Timing controller(board)LCD= Liquid crystal displayACF= Anisotropic conductive film

To provide you more detailed instruction, you can also click ASUS Youtube video link below to know more about troubleshooting for LCD Monitor problem (blurry screen, abnormal colors)