1.8 serial spi tft lcd module display arduino manufacturer

ER-TFT018-2 is 128x160 dots 1.8" color tft lcd module display with ILI9163C controller ,optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 1.8"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

I newer in arduino and buy this item from ebay. The pin configuration of the display does not match with any which i found in the web, can you help me with the identification?

I would like the help of some one of you to identify the pin configuration and the advice for some reading material relevant to understand how to manage this display.

{"id":4293518786631,"title":"Mini 1.8 Inch Serial SPI TFT LCD Module Display with PCB Adapter IC 128x160 Dot Matrix 3.3V 5V IO Inerface Cmmpatible 1602 5110","handle":"mini-1-8-inch-serial-spi-tft-lcd-module-display-with-pcb-adapter-ic-128x160-dot-matrix-3-3v-5v-io-inerface-cmmpatible-1602-5110","description":"\u003cp\u003e\u003cstrong\u003eDescription:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e100% Brand New\u003cbr\u003e1.8\\\" Serial Port SPI TFT LCD Display Module\u003cbr\u003eSize: 1.8 inch\u003cbr\u003eDot Matrix: 128*160\u003cbr\u003eModule Size: 44.96(length)X53.47mm(width)\u003cbr\u003eDisplay Area Size: 35.04(length)*28.03mm(width)\u003cbr\u003eInput Voltage: 5V\/3.3V\u003cbr\u003ePin Definition: 1-RST 2-CE 3-D\/C 4-DIN 5-CLK 6-UCC 7-BL 8-GND\u003cbr\u003eIt has PCB backplane with power IC, SD card socket\u003cbr\u003eIt need 4 IO port at least to drive.\u003cbr\u003eThe module port is compatible with 1602 LCD and 5110\/3310 LCD Display port.\u003cbr\u003epackage included:1pc 1.8\\\" SPI TFT LCD Display Module Serial 128*160 PCB Adapter Power IC SD Socket \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv\u003e\n\u003cdiv\u003e 1 x  1.8 Inch Mini Serial SPI TFT LCD Module Display with PCB Adapter ST7735B IC\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2019-10-21T15:25:21+08:00","created_at":"2019-10-21T15:31:02+08:00","vendor":"diymore","type":"LCD Display Module","tags":[],"price":599,"price_min":599,"price_max":599,"available":true,"price_varies":false,"compare_at_price":1200,"compare_at_price_min":1200,"compare_at_price_max":1200,"compare_at_price_varies":false,"variants":[{"id":30930193023047,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"030100","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Mini 1.8 Inch Serial SPI TFT LCD Module Display with PCB Adapter IC 128x160 Dot Matrix 3.3V 5V IO Inerface Cmmpatible 1602 5110","public_title":null,"options":["Default Title"],"price":599,"weight":0,"compare_at_price":1200,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_1_265.jpg?v=1588665768","\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_2_772.jpg?v=1588665768","\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_3_452.jpg?v=1588665768","\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_4_260.jpg?v=1588665768","\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_5_895.jpg?v=1588665768","\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_6_484.jpg?v=1588665768"],"featured_image":"\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_1_265.jpg?v=1588665768","options":["Title"],"media":[{"alt":"Mini 1.8 Inch Serial Spi Tft Lcd Module Display With Pcb Adapter Ic 128X160 Dot Matrix 3.3V 5V Io","id":6679589519431,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_1_265.jpg?v=1588665768"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_1_265.jpg?v=1588665768","width":1000},{"alt":"Mini 1.8 Inch Serial Spi Tft Lcd Module Display With Pcb Adapter Ic 128X160 Dot Matrix 3.3V 5V Io","id":6679589650503,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_2_772.jpg?v=1588665768"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_2_772.jpg?v=1588665768","width":1000},{"alt":"Mini 1.8 Inch Serial Spi Tft Lcd Module Display With Pcb Adapter Ic 128X160 Dot Matrix 3.3V 5V Io","id":6679590240327,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_3_452.jpg?v=1588665768"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_3_452.jpg?v=1588665768","width":1000},{"alt":"Mini 1.8 Inch Serial Spi Tft Lcd Module Display With Pcb Adapter Ic 128X160 Dot Matrix 3.3V 5V Io","id":6679590600775,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_4_260.jpg?v=1588665768"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_4_260.jpg?v=1588665768","width":1000},{"alt":"Mini 1.8 Inch Serial Spi Tft Lcd Module Display With Pcb Adapter Ic 128X160 Dot Matrix 3.3V 5V Io","id":6679590895687,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_5_895.jpg?v=1588665768"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_5_895.jpg?v=1588665768","width":1000},{"alt":"Mini 1.8 Inch Serial Spi Tft Lcd Module Display With Pcb Adapter Ic 128X160 Dot Matrix 3.3V 5V Io","id":6679591223367,"position":6,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_6_484.jpg?v=1588665768"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0122\/7558\/0986\/products\/030100_6_484.jpg?v=1588665768","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cp\u003e\u003cstrong\u003eDescription:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e100% Brand New\u003cbr\u003e1.8\\\" Serial Port SPI TFT LCD Display Module\u003cbr\u003eSize: 1.8 inch\u003cbr\u003eDot Matrix: 128*160\u003cbr\u003eModule Size: 44.96(length)X53.47mm(width)\u003cbr\u003eDisplay Area Size: 35.04(length)*28.03mm(width)\u003cbr\u003eInput Voltage: 5V\/3.3V\u003cbr\u003ePin Definition: 1-RST 2-CE 3-D\/C 4-DIN 5-CLK 6-UCC 7-BL 8-GND\u003cbr\u003eIt has PCB backplane with power IC, SD card socket\u003cbr\u003eIt need 4 IO port at least to drive.\u003cbr\u003eThe module port is compatible with 1602 LCD and 5110\/3310 LCD Display port.\u003cbr\u003epackage included:1pc 1.8\\\" SPI TFT LCD Display Module Serial 128*160 PCB Adapter Power IC SD Socket \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePackage Included:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv\u003e\n\u003cdiv\u003e 1 x  1.8 Inch Mini Serial SPI TFT LCD Module Display with PCB Adapter ST7735B IC\u003c\/div\u003e\n\u003c\/div\u003e"}

Please contact us for documents and driver if you need. Please noted this LCD is 3.3V, which can not receive 5V signals from the Arduino, so please use a 1k series resistors between GPIO lines on a 5V arduino and this LCD, power this LCD with 5V but drive it with "level shifted resistor" GPIO lines.

The 1.8inch LCD uses the PH2.0 8PIN interface, which can be connected to the Raspberry Pi according to the above table: (Please connect according to the pin definition table. The color of the wiring in the picture is for reference only, and the actual color shall prevail.)

ST7735S is a 132*162 pixel LCD, and this product is a 128*160 pixel LCD, so some processing has been done on the display: the display starts from the second pixel in the horizontal direction, and the first pixel in the vertical direction. Start to display, so as to ensure that the position corresponding to the RAM in the LCD is consistent with the actual position when displayed.

The LCD supports 12-bit, 16-bit and 18-bit input color formats per pixel, namely RGB444, RGB565, RGB666 three color formats, this routine uses RGB565 color format, which is also a commonly used RGB format

Note: Different from the traditional SPI protocol, the data line from the slave to the master is hidden since the device only has display requirement.

CPOL determines the level of the serial synchronous clock at idle state. When CPOL = 0, the level is Low. However, CPOL has little effect to the transmission.

CPHA determines whether data is collected at the first clock edge or at the second clock edge of serial synchronous clock; when CPHL = 0, data is collected at the first clock edge.

Framebuffer uses a video output device to drive a video display device from a memory buffer containing complete frame data. Simply put, a memory area is used to store the display content, and the display content can be changed by changing the data in the memory.

If you need to draw pictures or display Chinese and English characters, we provide some basic functions here about some graphics processing in the directory RaspberryPi\c\lib\GUI\GUI_Paint.c(.h).

Set points of the display position and color in the buffer: here is the core GUI function, processing points display position and color in the buffer.

The fill color of a certain window in the image buffer: the image buffer part of the window filled with a certain color, usually used to fresh the screen into blank, often used for time display, fresh the last second of the screen.

Display time: in the image buffer,use (Xstart Ystart) as the left vertex, display time,you can choose Ascii visual character font, font foreground color, font background color.

2. The module_init() function is automatically called in the INIT () initializer on the LCD, but the module_exit() function needs to be called by itself.

Python has an image library PIL official library link, it does not need to write code from the logical layer like C and can directly call to the image library for image processing. The following will take a 1.54-inch LCD as an example, we provide a brief description of the demo.

Note: Each character library contains different characters; If some characters cannot be displayed, it is recommended that you can refer to the encoding set ro used.

The first parameter is a tuple of 2 elements, with (40, 50) as the left vertex, the font is Font2, and the fill is the font color. You can directly make fill = "WHITE", because the regular color value is already defined Well, of course, you can also use fill = (128,255,128), the parentheses correspond to the values of the three RGB colors so that you can precisely control the color you want. The second sentence shows Micro Snow Electronics, using Font3, the font color is white.

The demo is developed based on the HAL library. Download the demo, find the STM32 program file directory, and open the LCD_demo.uvprojx in the STM32\STM32F103RBT6\MDK-ARM directory to check the program.

For the screen, if you need to draw pictures, display Chinese and English characters, display pictures, etc., you can use the upper application to do, and we provide some basic functions here about some graphics processing in the directory STM32\STM32F103RB\User\GUI_DEV\GUI_Paint.c(.h)

Image buffer part of the window filling color: the image buffer part of the window filled with a certain color, generally as a window whitewashing function, often used for time display, whitewashing on a second

Display time: in the image buffer,use (Xstart Ystart) as the left vertex, display time,you can choose Ascii visual character font, font foreground color, font background color.

DEV_Config.cpp(.h): It is the hardware interface definition, which encapsulates the read and write pin levels, SPI transmission data, and pin initialization;

image.cpp(.h): is the image data, which can convert any BMP image into a 16-bit true color image array through Img2Lcd (downloadable in the development data).

The hardware interface is defined in the two files DEV_Config.cpp(.h), and functions such as read and write pin level, delay, and SPI transmission are encapsulated.

For the screen, if you need to draw pictures, display Chinese and English characters, display pictures, etc., you can use the upper application to do, and we provide some basic functions here about some graphics processing in the directory GUI_Paint.c(.h)

Display time: in the image buffer,use (Xstart Ystart) as the left vertex, display time,you can choose Ascii visual character font, font foreground color, font background color.

This is a single-chip controller/driver for 262K-color, graphic type TFT-LCD.  It consists of 396 source line and 162 gate line driving circuits. This chip is capable of connecting directly to an external microprocessor, and accepts Serial Peripheral Interface (SPI), 8-bit/9-bit/16-bit/18-bit parallel interface.

The Graphic LCD screen is a backlit TFT LCD screen with headers. You can draw text, images, and shapes to the screen with the GLCD library. There is an onboard micro-SD card slot on the back of the screen that can, among other things, store bitmap images for the screen to display.

The screen"s headers are designed to fit into the socket on the front of Esplora, but it is compatible with any AVR-based (Uno, Leonardo), Datasheet You can use this module with Esplora.

In this guide we’re going to show you how you can use the 1.8 TFT display with the Arduino. You’ll learn how to wire the display, write text, draw shapes and display images on the screen.

The 1.8 TFT is a colorful display with 128 x 160 color pixels. The display can load images from an SD card – it has an SD card slot at the back. The following figure shows the screen front and back view.

This module uses SPI communication – see the wiring below . To control the display we’ll use the TFT library, which is already included with Arduino IDE 1.0.5 and later.

The TFT display communicates with the Arduino via SPI communication, so you need to include the SPI library on your code. We also use the TFT library to write and draw on the display.

In which “Hello, World!” is the text you want to display and the (x, y) coordinate is the location where you want to start display text on the screen.

The 1.8 TFT display can load images from the SD card. To read from the SD card you use the SD library, already included in the Arduino IDE software. Follow the next steps to display an image on the display:

Note: some people find issues with this display when trying to read from the SD card. We don’t know why that happens. In fact, we tested a couple of times and it worked well, and then, when we were about to record to show you the final result, the display didn’t recognized the SD card anymore – we’re not sure if it’s a problem with the SD card holder that doesn’t establish a proper connection with the SD card. However, we are sure these instructions work, because we’ve tested them.

In this guide we’ve shown you how to use the 1.8 TFT display with the Arduino: display text, draw shapes and display images. You can easily add a nice visual interface to your projects using this display.

This lovely little display breakout is the best way to add a small, colorful, and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.8″ display has 128×160 color pixels. Unlike the low-cost Nokia 6110 and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 18-bit color (262,144 shades!). And the 4.6 cm (1.8 “) SPI 128×160 TFT LCD Display Module will always come with the same driver chip so there are no worries that your code will not work from one to the other. The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. It features a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card.