3.2 ips tft lcd display 480x320 in stock

This TFT 3.5 Inch LCD display support 480x320 pixel resolutions. The display uses the ILI9481 graphics controller. The module includes the 5V-3.3V power conversion circuit and no additional level conversion circuitry is required. This Module can be inserted directly into the Arduino Mega2560 Board.

This 262K color 320 x 480 resolutions LCD module uses a thin-film-transistor liquid crystal display (TFT LCD) to improve image qualities. With controller HX8357B included in the screen, it supports a 16-wires Data Bus Interface. This module also includes a 5V-3.3V power conversion circuit and a level conversion circuit. 100% compatible with Mega2560, it can be directly inserted into the Mega 2560 Board. Additionally, it comes with SD card socket and SPI flash circuit. Definitely a powerful module for your projects!

Model No.NX3224T028Display TypeNX3224T024_011R (R: Resistive touchscreen)Operating Voltage (VDC)4.75 ~ 7Max. Operating Current (mA)90Display Layout Size (L x W x H) mm 74.4 42.9 5.8Net weight (gm)25Touch TypeResistiveColors65K (65536)Recommended Power Supply5V, 500mA, DCWorking Temperature...

LCD TYPE :TFT LCD INTERFACE: 24-bit parallel TOUCH SCREEN INTERFACE: 4 wires, capacitive TOUCH CONTROLLER: GT911 BACKLIGHT: LED DISPLAY SIZE (MM): 154.08 (W) × 85.92 (H) DOT PITCH (MM): 0.0642 (W) × 0.1790 (H) ASPECT RATIO: 8 : 5 RESOLUTION: 800 * 480 (Pixel) POWER CONSUMPTION: TBD BACKLIGHT CURRENT: TBD OPERATING TEMP. (℃): TBD

LCD TYPE TFTINTERFACE RGB/LVDSTOUCH CONTROLLER FT5406TOUCH PANEL TYPE Capacitive (5 multi-touch)BACKLIGHT LEDDISPLAY SIZE (MM) 222.72(W)×125.28(H)DOT PITCH (MM) 0.2175(W)×0.2088(H)ASPECT RATIO 16 : 9RESOLUTION 1024 × 3(RGB) x 600 (Pixel)POWER CONSUMPTION TBDBACKLIGHT CURRENT TBDOPERATING TEMP. (℃) 0 ~ +70

Operating voltage: 3.3V/5V (Please ensure that the power supply voltage and logic voltage are consistent, otherwise it will not work properly) Interface: SPI LCD type: IPS Controller: ST7789 Resolution: 135(H)RGB x 240(V) Display area: 14.864（H）x 24.912（V）mm Pixel size: 0.1101（H）x 0.1035（V）mm Dimension: 35(H) x 32(V) mm

Operating voltage: 3.3V/5V Interface: SPI LCD type: IPS Controller: GC9A01 Resolution: 240 (H)RGB x 240(V) Display size: Φ32.4mm Pixel size: 0.135（H）x 0.135（V）mm Dimension: 40.4 × 37.5(mm) Φ37.5(mm)

Working voltage: 3.3V/5V (please ensure that the power supply voltage and logic voltage are consistent, otherwise it will not work properly) Communication interface: SPI Screen Type: IPS Control chip: ST7789V3 Resolution: 172(H)RGB x 320(V) Display size: 17.39 x 32.35 mm Pixel pitch: 0.0337(H) x 0.1011(V) mm Product size: 22.0 × 38.5 mm

Operating voltage: 3.3V/5V(Please ensure that the power supply voltage and logic voltage are consistent, otherwise it will not work properly) Interface: SPI LCD type: IPS Controller: ST7789 Resolution: 240(H)RGB x 240(V) Display area: 27.72（H）x 27.72（V）mm Pixel size: 0.1155（H）x 0.1155（V）mm Dimension: 50 x 35(mm)

Operating voltage: 3.3V/5V (When using 5V power supply, the logic voltage is 5V; When using 3.3V power supply, the logic voltage is 3.3V) Interface: SPI LCD Type: TFT Controller: IL9341 Resolution: 240(V) x 320(H)RGB Display Size: 36.72（H）x 48.96（V）mm Pixel Size: 0.153（H）x 0.153（V）mm Dimension: 70.5 x 43.3(mm)

DRIVER CHIP 1306INTERFACE 3-wire SPI, 4-wire SPI, I2CRESOLUTION 128*64DISPLAY SIZE 0.96inchCOLORS 1/4 yellow section, 3/4 blue sectionVISIBLE ANGLE >160°OPERATING TEMP. (℃) -20~70STORAGE TEMP. (℃) -30~80OPERATING VOLTAGE 3.3V / 5VAPPLICABILITY Hardware platforms such as Raspberry Pi/Jetson Nano/Arduino/STM32

2.8-inch IPS screen with a hardware resolution of 480 × 640. Onboard dual touch circuit, touch can be driven via USB(drive-free) touch interface or I2C interface of Raspberry Pi, 5-point touch, toughened glass capacitive touch panel, hardness up to 6H Use with Raspberry Pi, it supports Raspberry Pi OS / Ubuntu / Kali / Retropie and WIN10 IoT. Use with...

3.5inch IPS screen, 480 x 320 hardware resolution, which can be set by the software (up to 1920x1080). Resistive touch control. Compatible and Direct-connect with any revision of Raspberry Pi. (If you are using a Raspberry Pi Zero / Zero 2 W, an additional HDMI cable is required.) Supports Raspberry Pi OS / Ubuntu / Kali and Retropie systems. Also works...

4inch IPS screen, with a hardware resolution of 480 × 800. Resistive touch control. Compatible with and can be directly connected to any version of Raspberry Pi. (If you are using a Raspberry Pi Zero / Zero 2 W, an additional HDMI cable is required.) Supports Raspberry Pi OS / Ubuntu / Kali and Retropie systems. Also works as a computer monitor, in this...

4-inch IPS screen, hardware resolution is 720 × 720. 5-point capacitive touch, tempered glass panel, hardness up to 6H. When used with Raspberry Pi, it supports Raspberry Pi OS / Ubuntu / Kali and Retropie. Ubuntu is supported when used with Jetson Nano. When used as a computer monitor, it supports Windows 11/10/8.1/8/7. Onboard dual touch circuit,...

4.3inch IPS screen, 800 x 480 hardware resolution. 5-point capacitive touch control, tempered glass panel, hardness up to 6H. When working with Raspberry Pi, it supports Raspberry Pi OS / Ubuntu / Kali and Retropie systems. When working as a computer monitor, it supports Windows 11/10/8.1/8/7, five-point touch. Multi-languages OSD menu, for power...

Contrast600:1Display Color16.7M (6bits + Hi-FRC)Operating Voltage (VDC)12Max. Operating Current (mA)2A MAXDisplay Size (inch)10.1HDMI PortHDMI 1.1Interface TypeDigitalLuminance350 cd/m2Number of Wiring40 Pin LVDSPanel TypeTFTPhysical Resolution1280 x 800

Driver : HX8347D Touch Controller : XPT2046 LCD Type : IPS Communication Interface : SPI Display Colors : RGB, 65K colors Resolution : 320 x 240 Backlight : LED Display Size (mm) : 57.6mm 43.2mm Touch Type : 4-wire Resistive Power Supply Voltage : 5V Logic Level : 3.3V

Lcd Type: TFT Lcd Interface: SPI Touch Screen Type: Resistive Touch Screen Controller: XPT2046 Colors: 65536 Backlight: LED Resolution: 320*480 (Pixel) Aspect Ratio: 8:5

If using the UTFT library from RinkyDink electronics, open up their initlcd.h file. In the section for Memory Access Control (lines 85-86 in version I have), change the write to:

ER-TFT032-2 is 240x320 dots 3.2 " color tft lcd module display with ILI9320 controller and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 16-bit parallel interface. .FPC is soldering type,there is no need for zif connector.Lanscape mode is also available.

For smaller projects, LCD and ePaper displays are a fun way to add a visual element to your projects. With simple code and wiring, they’re great for projects that require text, menus and navigation.

This display can be mounted on an Arduino Mega or Due. It has a fairly high resolution of 320*480 pixels and is also quite large with 3.2 inch LCD size.

Note: The appearance of this display may differ slightly because our supplier may supply a slightly different version where the circuit board size is different. However, this is mostly similar and are controlled in the same way.