3.2 inch ili9341 tft lcd datasheet price

Reason: The hooks on the backight of ER-TFT032-3.1 is always complained by most customers for inconvenient assembly. So we cancel the hooks in the new version of ER-TFT032-3.2.That"s the only difference for these two versions.

ER-TFT032-3.2 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller and optional 4-wire resistive touch panel and 3.2 inch capactive touch panel with controller FT6236,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8/16-bit parallel,3/4-wire serial interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

967 3.2 inch tft lcd module display products are offered for sale by suppliers on Alibaba.com, of which lcd modules accounts for 83%, segment displays accounts for 1%.

A wide variety of 3.2 inch tft lcd module display options are available to you, You can also choose from datasheet, 3.2 inch tft lcd module display,as well as from tft, ips, and standard 3.2 inch tft lcd module display,

It has 40 pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project. The Screen include a controller ILI9341, it"s a support 8/16 bit data interface , easy to drive by many MCU like arduino families? STM32, AVR and 8051. It is designed with a touch controller in it . The touch IC is XPT2046 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

262K color320*2403.2 inchWide viewing angleILI9341 : 320 TFT Driver X 240 RGBIntegrated Power, Gate and Source Driver With RAMXPT2046-WIRE TOUCH,WIRE TOUCH, UP TO 125kHz CONVERSION RATE, SERIAL INTERFACEVoltage type : 5v or 3v voltage input voltage?input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.Note: the factory TFT module, are the 5 v power supply. By default.Carrying on board SD holder, its work to SPI mode.By the use of Stylus we can write anything on Display.

This is a multicolored TFT display with touchscreen and on-board SD card socket. It is based on the ILI9341controller, with a 16 bit parallel port data bus and a 4 bit control interface. This 3.2” TFT LCD touch shield is compatible with Arduino Mega and it also works with the Chipkit MAX32 board since it can operate at both 3.3 V to 5 V.

This TFT display is 3.2" diagonal with a bright 4 white-LED backlight with a resolution of 320x240. It has way more resolution than a black and white 128x64 display. As a bonus, this display comes with a resistive touchscreen attached to it already, so you can use the stylus on the screen.