lcd screen bubbles quotation

The big bubble is adjacent to the edge and might indicate air leaking in, but not the small bubbles. An autoclave will not help with the small bubbles, and the big bubble will need re-gluing, which is rather complicated

Pressing will not help, as at least one upper layer glued to the LCD is hard. Repairing is a time-consuming job that requires separating and replacing however many layers are glued to the LCD screen, and damage can easily happen.

Most repairmen will prefer just replacing the screen, as the above can take hours and a mistake may be fatal to the LCD. You might be able to find a cheap replacement screen on Alibaba or similar.

You know the dealership is trying to say that my car which is still under bumper to bumper warranty mind you is not qualified for a replacement because this is considered cosmetic. Let me explain as to why this isn�t cosmetic. During the manufacturing process the laminate that was used was not put on properly which is why you are seeing people with these issues. I�ve seen cars that are 10 years old with screen that have had 0 issues! This is a 3 1/2 year old car! Could have been the quality of laminate a bad batch of glue either way this will eventually get worse and obstruct you�re view of the screen. They should be replacing them without question! This isn�t something I have done to it. It happened because it�s a manufacture defect! Interestingly enough people seemed to be having luck getting them replaced by BMW at a certain point. Until they realized they messed up and decided to cut the cost of replacing them and calling it a �cosmetic� issue therefore avoiding having to replace it in their shady bumper to bumper warranty. The dealership had the audacity to offer me 50% off the screen! Only 1800 dollars LMAO! Awesome BMW Long Beach! I have reached out to BMW NA we will see how this goes. It�s not about the cost of the screen it�s about doing the right thing. Companies are constantly doing things like this and I�m getting sick of it!

Just recently I"ve noticed a very sticky liquid leaking out of one corner of the screen. There are now bright and dark patches on the screen near where it"s leaking. As well as round the screen the sticky stuff gets onto the base of the laptop where I rest my hands to type. lt"s really hard to clean off and I"m worried it may be toxic.

One of the most important ways you can ensure the highest payment for your broken LCDs is to ensure they are safely packed before shipping. Please remember: the total value in each shipment is determined by the number of good LCD screens and spare parts, not just in the number LCD screens shipped. Typically, your LCD screens are already broken in some way.

Manufactures do not design the LCD screens to withstand the elements once removed from a handset. Pressure points, dust, dirt, moisture and the chances of electronic static discharge are greatly increased once removed.

Consider a safe storage area for your LCD screens the moment they’re removed from the mobile device. Placing the defective LCD screen back into a bubble bag or storage sleeve is considered best practice.

1. Place LCD screens Face to Face with flex cables positioned in the same direction. This protects the LCDs as well as provides more space within your shipment.

3. Stack 5 pairs to complete a set of 10 total LCD screens. As mentioned above, these 10 total screens are face to face and back to back. Packing more than 10 to a set increases chances of breakage; any less wastes unnecessary packing space.

4. Secure each set of 10 LCD screens in bubble wrap or other protective material. Taping the bubbles sets is recommended. You want the wrapping to be tight enough so the LCD screens do not shift around, but not tight to the point where pressure might damage the screens.

NOTE: If you do not have bubble wrap, using a rubber band to secure sets of 10 screens along with multiple layers of newspaper is better than not wrapping at all.

5. Place sets of screens in the packing box. Use a layer of bubbles, crinkled newspaper, or other material to line the bottom of the box. It’s best to line the sides of the box once you have a few sets in the box along with more crinkled newspaper on top.

It’s highly recommended that each box contains no more than 350-400 LCD or exceeds 35lbs in weight. Also make sure you do not exceed the weight limit of the box.

To solve the problem with repairing and refurbishing the cellphone screens, many OCA Bubble Removal Machines are coming up on the cellphone repair market. It is a good helper to assist you in fixing cellphones perfectly in a short time, and it is so easy for you to operate with higher safety factor. However, you should finish all steps with lamination of the glass and LCD screen before you use a machine to remove the bubbles which remain on the cellphone screens.

You can see that most people are not able to live without a smartphone in their daily life. You know, the smartphone can do many things in our life. Like pay for the bills, take photos, make free video calls with anyone around the world, shop online and do business with people in the globe, etc. The smartphone is very useful, and it is very small so that we can take it conveniently. However, if you drop the cellphone on the ground carelessly, it may leave a crack on the glass of the phone. So you have to change the entire screen or get a new phone, you know it would spend much money and time to change the screen or get a new phone just because the cellphone leaves a grave impact on the phone. You would think it isn’t worth to do it.

To solve the problem with the repair of cellphone screen, many LCD laminating machines and bubble remover machines are extensively coming up in the cellphone repair or refurbish market. The machines can help people to repair the screen at a low price and help the repair stores or phone repair industry to get tremendous profitable.

These machines have gained increased popularity due to how easy and profitable they are. The machine is used to remove bubbles that form on the cellphone’s screens after OCA and LCD lamination.

During the process of refurbishing the cellphones’ screens, repairers would like to use a laminating machine that typically leaves room for some bubbles on the phone’s screen. These bubbles are usually too tiny to be seen with our naked eyes. However, the final stage of refurbishment causes these tiny bubbles to move to each other, forming a visible bubble on the screen.

The machine is designed to sniff out any invisible bubble and conduct an automatic cleansing after lamination. This machine provides a lasting OCA bubble problem solution to ensure that any bubble, no matter visible and invisible, lurking underneath the screen of the phone is wiped out, thus, helping you get that perfect look at first try.

Thus, you have to learn how to laminate OCA and LCD screen first before bubble removing. This is because bubble removing is the step just after lamination.

The most important things are that you should finish all steps with the glass or LCD screen lamination at first, and then use bubble remover to remove bubbles.