how to replace lcd screen on canon camera factory

The 2nd ribbon on the LEFT is a bit trickier, but not hard. There is a grey slot that is locking the larger ribbon in place. You need to pry that grey slot/level open so that you can take out the ribbon. Important detail!

There also should be instructions regarding how to replace the screen. For example, if you have just an LCD (and not a backlight to go with it), then you need to remove the LCD from the backlight.

If your order came with a backlight, then you need to take the little silver case that all the screws screw into, and remove it from the backlight, and install it onto your new LCD/Backlight. Should have pictures for that.

If either your screen is damaged or you cannot see an image on the screen of your Canon PowerShot SX60 HS then use this guide to replace the LCD screen.

A very common camera repair performed today, no matter the type or manufacturer, is the replacement of the LCD (Liquid Crystal Display) screen. At the outset of this walkthrough a few things must be stressed; a disclaimer if you will. Trying to replace an LCD without proper knowledge and experience can be very difficult and sometimes hazardous. Pulling electronics apart and seeing how they work can be fun for some, but it can easily result in further damage and far more costly repairs. Nine times out of ten, when an LCD is being replaced, it is physically broken due to damage that was likely caused by some sort of trauma (from dropping etc).

Cameras are very tightly packed little pieces of technology and generally the LCD is attached to and/or part of a lot of other integral components. Because of this, there is a high probability that there are other things broken that only a trained professional can diagnose/fix easily. Also, having spare parts on hand doesn’t make economic sense for your average consumer because the costs of replacement parts for cameras are not in proportion to their selling price.

Furthermore, camera repair facilities have the necessary testing, calibration and adjustment equipment to get cameras fully operational. Bottom line, if one does attempt this at home, there is very little to no margin for error. Keep in mind this is a general walkthrough NOT a repair guide, I take no responsibility for any damage to property or personal harm that may occur from anyone making use of this information. With that said…

The first things first, parts and tools are necessary to doing this job right. Obviously the part needed is a replacement LCD. It has to be for that particular make and model; this ensures the connections align and it fits properly. The essential tools for “most” LCD replacements are:

And now for the show, replacing the LCD! Please keep in mind this is a general many camera models are more complex and will require additional disassembly in order to remove and replace the LCD.

Location and unscrewing of all housing screws to remove the necessary housing cover(s).It is easy to strip out the tiny screw heads; many manufacturers “glue” the screws in place. If the LCD was damaged due to impact, the housing may have shifted, making the screws problematic to remove.

Proprietary screws can also be a problematic; the screwdriver may have to be special ordered from the manufacturer. Screws may also be hidden behind stickers or panels.

There is a very real risk of shock from this point on. DO NOT TOUCH ANY CIRCUITRY. The flash capacitor circuit on some models is located nearby and will give a painfull serious jolt if one is not careful.

The screws securing the LCD to the rest of the camera are now removed. These are fairly easy to find but there may be additional clips or seals to watch out for.

Connecting components (generally wires or FPC’s) that run from the LCD to the rest of the camera are disconnected using the appropriate set of tweezers.

The new LCD has a protective plastic sheet that is removed before installation. Touching it with bare hands must be avoided, potential damage could be done. It’s also in bad form to get any oils on the nice new LCD screen.

The Battery and memory card are replaced and the camera is powered on. This only tests if the LCD was installed correctly. If the camera/LCD is not working there are countless other things that could be going wrong and are evaluated. As mentioned in the beginning, there is a high possibility that something else is broken and/or needed to be calibrated/adjusted. Further testing of the entire camera must be done to ensure the camera is fully operational.

Just to stress again, trying these kinds of repairs at home, can be a great hobby for some, shouldn’t be taken lightly. Professional photographers always have a backup camera in case of any type of equipment malfunction; it’s not a bad idea.

Kevin Gornto is a Factory Trained and Authorized Technician at C.R.I.S. Camera Services, a digital camera repair company located in Chandler, AZ. Kevin has an electronics degree that provided him with his advanced hardware knowledge and digital imaging expertise. He also enjoys writing about his technical experience and is a major contributor for the company’s camera repair blog; focused on care, maintenance and repair tips for digital cameras and imaging equipment.

I have successfully changed my LCD Screen on my PowerShot S400! With the help of this forum, I learned of the Canon Parts Center and phone number (732-521-7230). I couldn’t believe the price of $33.02 plus $5.00 s/h. (LCD screen part number WG2-5243-000…they don’t use the numbers printed on the screen itself) They sent it from NJ to CA in about a week. I was very reluctant to even take on such a project as replacing the LCD, but after researching locally for repair options, and getting a range of $230 to $300 to fix a $499 S400, I said “what the heck�. I would rather buy a brand new camera, than fix one for over half the price. (One local store said the LCD screen alone cost $195…what a con / rip). I must admit, I did first take apart the camera initially to see what was inside and if it would be way over my head (before even learning of the Canon Part Center).

First, make an investment in a GOOD set of precision screwdrivers (sandblasted tips for a good grip). I went out and bought a 12-piece set of Sears Craftsman Micro-Tech Precision Screwdrivers ($19.99) … you only need one of the Phillip’s head and one of the slotted, but I will probably need the rest at some time, plus the set has a lifetime warranty. Sears sells smaller sets or individual screwdrivers.

First remove all of the outer screws, KEEP TRACK OF WHAT SCREWS GO WHERE, THEY ARE DIFFERENT LENGTHS!!! The outer case / covers comes apart in two pieces surprisingly easily, and the knobs, buttons, switches, etc. stay intact in the outer cases. The hardest part is “prying� the old LCD Screen out of the frame / holder. I would strongly recommend buying the new LCD Screen first, so you know what is being replaced and what is the frame that the screen snaps in to versus what is the LCD screen. Use a small slotted screwdriver to “pop� out the screen from the holder. Pry / twist the screwdriver from between the LCD and the back area behind the LCD. Work around the two ends of the LCD (short sides). If you use the magnify glass, you can see small dimples of metal that press against the LCD to hold it in place under pressure.

Remove the bottom metal plate (one screw next to the tripod hole)….wiggle this plate free…a part of this plate slides under the battery door hinge area.

Remove the screw under the flash to release the copper / plastic shield covering the entire PC board in order to get to the connector. Unplug the flexible connector from the PC board…carefully just pull it out. When you pull out the flexible connector, it causes a clip to pop up, releasing the connector. Don’t worry, this “clip� is hinged and will not fly out. It is a little tricky putting the new connector back in. It does not just plug in. Slide the connector in the slot, and then push down on the hinged clip to push down and hold the connector…it will click closed.

Re-assemble the covers, compact flash door, etc. Be careful of the spring that the compact flash door uses. One of the great things about working with a precision piece of equipment such as the Canon S400, is that it goes back together exactly as it was taken apart, if it doesn’t, you haven’t aligned / done something right…don’t force anything.

Disclaimer: I think I have listed the most important steps. Some of the instructions may not make any sense until you open up the camera to see the parts I am talking about. These steps were successful in repairing my camera, but I knew that only the LCD screen was damaged, and nothing else. I am somewhat mechanically inclined. You need a steady hand (drug addicts should not attempt this repair). If you can change a battery in a watch, you should be able to do this. Take your time; get a clean work area with good lighting. It took about an hour to do this job….less time than writing this letter.

I was motivated to write this letter to “give back to Society�. After being lied to and almost ripped off by the camera repair shops, I felt a civic duty. Here is some advice that is absolutely priceless. This whole broken LCD disaster could have been avoided for 59 cents. I had a $20 soft nylon case for the camera. I LOVE this camera because of the small size and excellent quality. My philosophy in making any purchase (no matter the price), is that it has to be used. Big and bulky cameras are too inconvenient to dash around with. I broke my camera because I forgot it was in my pocket and slammed my car door against it (I know…how stupid). A very good and knowledgeable sales guy warned me about that….people forget they have it in their pocket and run into things. For 59 cents, go to Target, buy a hard plastic soap box, used to traveling (they come in some puke colors). The S400 fits PERFECTLY in it. Cut a little slot for the hand strap to come out of and you are good to go. The saddest part of this story is that I purchased a second new S400 right after I broke the first one…then repaired the broken one. Now I have two perfectly functioning S400’s.

On other cameras, I have just pried up the old glass/protector and replaced it with a rear glass that I bought on Amazon for less than $10.00. I haven"t been able to find one for the R on Amazon or eBay. I called Canon Parts and all they could find was replacing the entire assembly which costs $135.00.

I checked our part catalogue and the LCD assembly is the only part, no cover screen, as far as we know. This is the case with a number of newer LCDs because they fill the space between screen and cover with a glue / filler to reduce the glare that an air space would have.

Whether you can or not is mostly a question about whether you"re comfortable doing some minor disassembly, plugging and unplugging flexes, etc. This tear down https://www.lensrentals.com/blog/2018/10/teardown-of-the-canon-eos-r-mirrorless-camera/ will probably give you enough information to decide your comfort level.

Bottom line is you"ll have to remove the back panel which isn"t hard if you"ve done any camera disassembly. If you haven"t done any camera disassembly, I"d vote not worth the risk.

I have previously activated the auto-shutdown feature to put the camera in sleep mode after about 5 mins of inactivity. So this should kick in after 5 mins, no?

When I checked the camera the next day, the battery was completely dead. It could mean either of two things: either the camera was on all night in video mode until the battery died (this could mean I did turn the auto shutdown feature off and I simply forgot), or I did actually set it up to record video all night and left it like that.

The battery that died was a third-party chinese battery. It died as it was in the camera. The next day I cherged the same battery and re-inserted it. The result was that screen in the picture above. I do have other batteries and I did try the original canon battery that came with the camera. At first it didn"t work but then it actually did turn on normally with the canon battery. But now, even with the canon battery, the display still remains scrambled and functionality is thrown out the window.

I"ve tried all combos - put the battery in while the power switch was on; put the battery in with power switch off; removed sd card, pwr sw off, insert battery, then pwr sw on; the combos go on. It doesn"t matter whether the power switch is on or off, the top lcd turns on like this as soon as I close the battery lid.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Yes we receive many cameras in the post every day. We recommend you pack your camera with at least 2 inches of padding around all sides, and use a tracked and insured courier service such as Royal Mail Special Delivery, or UPS.

We can arrange a courier collection or a pre-paid delivery label to make shipping easier. Just fill out our online repair form and select the option you prefer.

Estimates give you the most information before we start work on your canon camera, however they do add time to your repair. You can choose not to have an estimate in which case the camera goes straight to a technician for repair, you can also set a price limit for us to proceed up to so we can carry on quickly with minor repairs or give you an estimate before going ahead with more expensive work.

Our technicians can carry out warranty repairs in house on 1D, 5D, 6D, 7D and 90D cameras. Warranty repairs on other models can be sent directly to Canon or we can send the cameras to Canon on your behalf.

Do you sell spare parts for Canon?We can supply user replaceable spare parts for Canon cameras such as missing screws, rubber grips, battery doors and flash stands.

Spare parts which can only be fitted by dismantling the cameras, and which require thorough testing afterwards will not be supplied. These parts, such as bayonets, shutter assemblies and circuit boards, should be fitted by a trained technician who can safely dismantle and reassemble your Canon camera. Our technicians have all the technology supplied by Canon and years of repair experience to make sure each repair meets the Canon standard.

With repairs it is best and most economical to pinpoint the issue to one piece of kit, or to a combination of a Canon body and lens that is causing the problem. To give all your kit a check over we recommend using our Focus calibration service which has fixed rates and gives you a report on each body and lens.

Due to how easy it is for dust to get into the body of Canon cameras when you change lenses or even when you use a zoom lens, we cannot guarantee our sensor cleaning.

Canon automatic sensor cleaning is an option within the camera that shakes the CMOS sensor to dislodge dust. Stubborn spots of oil, sticky particles such as pollen and fingerprints do not shake off the CMOS sensor so easily and professional cleaning is recommended.

Yes we are proud to be part of the CPS service scheme. We offer priority repair turnaround to CPS Gold and CPS Platinum and CPS Silver customers. We can help CPS Platinum and Gold customers get loan equipment from Canon CPS if the repair will take longer than the target times of 2-3 days (Platinum) 3-4 days Gold.

Yes we can repair Canon cameras purchased from grey market retailers. However the cost of warranty repairs cannot be claimed back from Canon UK so the repair will be chargeable.

Yes. If the cover has come off of your mode dial we can replace it in 24 hours. If the mode dial is damaged or impacted we may need to replace the camera top cover. If this is the case we will provide a thorough estimate of the work required.

At Fixation we specialise in professional photographic repairs. We know that many professional photographers rely on Canon cameras to make their living. We do not use fixed prices, our technicians create a fresh assessment for each repair so that you only pay for what is wrong with your camera. We make sure that your Canon camera is serviced and repaired quickly, affordably and reliably.

I"ve replaced mine for $10 with a ebay screen from China. That was for a old point and shoot camera. I"ve also noted that prices were much higher for modern DSLR"s. As long as you have proper tools, JIS screwdrivers, not phillips, its just a simple job but requires cleanliness and patience.

Summary: Are you frustrated with your camera taking black pictures? Are the photos coming out dark or shadowy in spite of ample light during the shoot? It is probably because of wrong exposure. This post explains why camera photos turn out black and helps you with the 13 workable solutions to fix the issue.

You love to shoot amazing pictures with your digital camera. But suddenly the camera starts taking black pictures. Photos appear too dark. Indoor photos are black despite the ambient light. And you wonder why?

Photography is not just a creative pursuit but a skill mastered with practice. Nevertheless, you don’t need to wrap your head around this problem. Camera recording black or dark photos is a common issue. And can be easily fixed using the below methods: Set aperture, shutter speed, and ISO to prevent dark pictures

Your camera would do the best job when it receives the good amount of light. A combination of right aperture, shutter speed, and ISO settings is a key to perfect photos. When the 3 elements are not set to the correct level, your camera will produce underexposed, dark, or black photos.

In addition, the camera pictures can turn out black because of shooting on low battery or with a dirty lens. In case the LCD screen shows a black screen instead of a photo, the problem could be with the LCD backlighting.

To fix black pictures issue, first check the camera settings. If you are shooting in Manual Mode, fix the aperture, shutter speed, and ISO settings. Alternatively, you can try your camera’s default Auto mode or shoot in RAW.

If your camera is taking black pictures, work upon the aperture, shutter speed, and ISO settings. But to obtain the correct settings that bring the perfect exposure in the photos, it’s essential first to understand these 3 camera elements.

Aperture is a hole through which light enters your camera. The bigger the aperture more the light reaches into the camera sensor. It is measured in a focal ratio such as f/4.0, f/5.0, f/8.0, etc. The larger the focal-number, smaller is the aperture, i.e., lesser light passes the camera sensors. So aperture should be more to stop the camera from taking dark photos.

Shutter speed is the duration for which the shutter is opened. It is measured in a fraction of a second such as 1/10, 1/40, etc. Less shutter speed lets more light into the camera. Hence, when taking pictures at night, keep the shutter speed low. Further, shutter speed also affects the picture sharpness in motion photography. You can follow the common rule — to set the shutter speed as per the focal length of your camera lens. For example, if the camera focal length is 65 mm, set the shutter speed to 1/65.

ISO is the sensitivity of your camera sensor to light. Lower ISO results in darker photos. Conversely, you can brighten a picture by increasing the ISO number. ISO value usually starts from 100 and can go up to 6400, depending upon your camera. When shooting in less light, keep the camera ISO value higher to prevent the camera taking black pictures. Try to set it to at least 200. Further, depending upon light conditions, you may need to raise it to 1600 or above.

Having said this, a very high ISO can result in grainy photos. Thus, use camera ISO to brighten photos only when low shutter speed and bigger aperture are causing blur or noise in pictures.

In a nutshell, adjust these 3 photography aspects to an optimal level so that the maximum light enters the camera. And you get a bright photo without noise, blur, or grains.

As an amateur photographer, you may not want to fidget with the multiple settings in your camera. Instead, take advantage of the camera Auto, also called Program Mode. The automatic mode in the camera auto selects the aperture and shutter speed settings to generate the best possible light exposure in your photo.

Professional photographers commonly denounce the Auto Mode in contrast to Manual Mode. But modern cameras built-in Auto mode is improved and better. Mostly you can obtain a well-exposed photo without the annoying darkness.

In order to use Exposure Compensation, first select any of the camera mode such as Program Mode (P), Aperture Priority (A/ Av), Shutter Priority (S) or other scenic modes present in your camera. Remember, Exposure Compensation doesn’t work in Manual (M) mode. Once you select the camera mode, adjust the exposure value compensation to remove darkness from your photos.

The Exposure Value Compensation is indicated with (+/-) sign. Check for the sign over your digital camera. It should be typically available on a button or a dial, depending on your camera model. If you set the exposure value towards negative, the camera will take darker photos,whereas moving it to the positive sign, the pictures will get brighter.

Lighten up pictures by using the fill flash. The technique is best used to remove the darkness or shadowed areas from pictures when recording at night, dim light, or on extremely sunny day.

Typically, fill flash is used when the background is brighter than the subject in your frame. Like when your subject is in front of a sun-dappled river or a snowy mountain. Using the technique, you can remove the dark cast over your photo’s subject and brighten up the overall picture.

However, be careful when adding light to the shadowed areas of your photo. Too much light or flash too close to the subject can muddle your images. Maintain a balance between the ambient exposure (the existing light) and your flash light. Professionals prefer to control the exposure manually using both camera’s exposure settings and flash settings.

Turn off your digital camera. Remove the battery for a few minutes and reinsert it. Make sure the camera battery is fully charged and properly inserted.

Cameras have options to record photos in JPEG and RAW. Choose to shoot in RAW format if you are getting dark JPEG pictures. The RAW file types capture all image data recorded by your camera sensor. The RAW format photos are of high quality and brighter compared to the compressed JPEG files.

You can also use the ‘Clean Image sensor’ option present in your camera. The feature removes the dust that sticks to camera sensors during exchange or change of lenses. You can find the sensor cleaning option in the menu of your digital camera.

If photos are black on camera LCD screen but appear fine on computer, it is possible that your LCD backlight is dead. Besides, to be rest assured that camera taking black pictures is actually an LCD display issue you can do the following checks: Make sure the digital camera powered on when viewing the photo.

If your camera LCD display still shows black and you can’t see any picture, contact the manufacturer for repair. If the camera is in warranty, they should replace the LCD display.

If the pictures continue to come out black, try by resetting your digital camera to default settings. The reset option may vary with camera model. For instance, Canon variants usually have ‘Clear all camera settings’ options whereas to reset Nikon DSLR, navigate to ‘Reset Shooting Options’ from the camera menu.

Histogram helps to assess the picture exposure settings on your camera LCD. It is a graphical representation of the brightness levels in the picture. You can quickly find if the photo is underexposed and change the camera settings accordingly.

If you see a tall spike on the left in the histogram, it indicates the photo is underexposedor dark. Whereas if the picture is overexposed, the spike will appear on the far right.

Do you already have dark or underexposed pictures and can’t reshoot them? Fix dark pictures using an advanced photo editor. Adobe Photoshop, Lightroom, Movavi, and others have multiple options to fix the brightness and contrast in your pictures. You can add hue/saturation adjustment layer, use filters or other features to enhance the image and minimize the dark cast.

If no technique works and the camera continues to take black or dark photos, contact your camera authorized service center. You can also email or call the manufacturer’s support service on its website.

If a perfectly shot photo appears completely black on your computer, it could be due to corruption. Image files stored in hard drive, SSD, camera memory card etc., can get corrupt due to virus infection, improper file transfer, bad sectors in drive and other reasons. The corrupt photos may appear black, grainy, color damaged, etc. However, you can repair them using photo repair software.

Photo repair tools don’t work like image editing software. They don’t fix overexposed, underexposed or other flaws in pictures caused due to wrong camera settings or poor light arrangements during shoot. Instead, they repair corrupt file header and data to bring back your photos in original form.

It’s annoying when your camera takes black photos. But now, with the given 13 ways in this post, you can easily fix the camera taking black or dark pictures problem.

Nishat Paiker is an expert technical writer and editor with over 8 years of experience. She has deep knowledge about data recovery and loves to explore new technology and DIY tools. Nishat has keen interest in photography. You will often find her giving photography tips and hacks.

Understanding how to repair a digital camera screen will keep your leading digital camera in good standing even in the worst-case scenario. While equipment maintenance is the best way to prevent problems, repair and replacement are two unavoidable realities. You’ll eventually run into malfunctions as your equipment ages.

It is never recommended to replace a digital camera screen yourself because the camera’s internal components are sensitive and you can easily interfere with the camera modes.

Learning how to repair a digital camera screen, or at least understanding the theory behind it, helps photographers immeasurably. Basic maintenance should be performed regularly so that your screen stays in good shape. If an issue does pop up, make sure you understand basic troubleshooting. Alternatively, if you’re just curious about focusing, you might like our info article on how to use a horizontal split focusing screen on a digital camera.

Problems with your digital camera screen can ruin your digital photos. After all, the biggest reason people love the digital camera experience is viewing photos in real-time while shooting, and the ability to connect to other devices such as the iPhone and share quality photos. There are a few issues that could be at play.

If your digital camera screen won’t turn on, there is an immediate issue to be resolved. The LCD screen could lack power from a battery issue, for example. No matter what, it’s time to take your camera to a professional to diagnose the problem. This, unfortunately, has nothing to do with the gamma in your digital camera, as that’s a separate matter altogether.

Accidental damage happens all the time to your lens. Lens and sensor damage is unavoidable since you constantly switch them out and expose sensitive parts to the open air. Make sure that your lens isn’t the reason your screen doesn’t seem to be working correctly. That said, if it is an issue, you’ll need to know how to repair a digital camera and lens.

Lastly, you’ll want to keep an eye on the camera whenever it’s out of its protective casing. Sometimes damage to property happens when you’re out and about. It doesn’t have to be done maliciously. Just knocking over a camera on accident can be enough for internal components to pop out of place.

If you’ve concluded that your problem is from a faulty LCD display, it’s time to reach out to a professional or the brand. Your destination for tech repair should hinge on the star rating the company has earned. Always go through a reputable repair shop to avoid further damage. If you’re set on trying to repair or replace an LCD screen display yourself, make sure you have the right repair tools for the job.

Quite a few things can go wrong and call for common camera repair services. Here are a few of them:You must replace defunct batteries with fresh batteries

Luckily, troubleshooting isn’t super complicated, and there are tons of answers in product info if you still have your owner’s manual. If not, head over to the brand website for more troubleshooting information.

You should always be following repair guides when attempting to fix anything yourself. Repair guides will give you a list of repair tools needed for the job.

There’s no way around it: contacting a digital camera repair company is always your best bet. While you can get the repair tools yourself, you risk dealing with further damage to your camera’s internal components. Sometimes cameras are beyond repair, as well, and a digital camera repair company is better suited to tell if you just need a new camera.

STAT: The statistic depicts the wholesale sales of digital camera accessories in the United States from 2018 to 2022. In 2019, digital camera accessories wholesale sales in the United States were estimated to amount to 83 million U.S. dollars. (source)