water in lcd screen brands

One of the most annoying phone problems is water getting inside your screen and damaging the electronics. But did you know that most phone screens aren’t completely waterproof? It’s not uncommon for your phone to get damp from an unexpected rain shower, or drop your phone in a sink, toilet, or pool.

But phone makers have been putting more and more technology into their phones to make them more durable and waterproof. The problem is that water under your phone screen can still cause problems.

If water has gotten under the phone’s screen, it’s a big problem. While phone manufacturers tend to make water-resistant phones (such as waterproof phones), they don’t make waterproof phones. That is, they still can be damaged by water. Some phones are resistant to random splashes or quick dunks in the water, while others are completely waterproof until a certain depth and for a specified time.

This article details what you can do if there’s water or moisture trapped underneath your phone’s screen.So, follow the steps or ways below & keep reading to find out more.

If you notice moisture or water droplets trapped underneath your phone’s screen then the first thing you should do is switch off your phone and remove it from any connected outlets. This is very important as doing this might just be the difference between a small repair and buying a brand-new phone.

If this is not done as soon as possible, there is a chance that it might short-circuit the internal system and fry the motherboard. As you may know, electricity and water do not interact well; this also might lead to the phone catching on fire, causing more damage and posing a significant threat.

Cutting the power of your phone—whether overnight or when you wake up—is an easy fix that can save you some frustration, and it won’t cost you anything.

The next thing you should do is to remove any and all removable components in your phone, such as the SIM tray, SD card tray, battery ( if it has a removable back ), etc. This will allow for more airflow into the internal parts of the phone;

If your phone develops a waterlogged problem, all may not be lost. Instead, you can salvage the situation by carefully taking all of the pieces off your phone and putting it back together. This is not as simple as it sounds, and certain phone models have additional steps to take.

If you notice any wetness around these areas, ensure you dry them off with a clean cloth. Next, you must leave your phone out to dry for at least a few hours, depending on how much moisture is inside the screen.

It’s critical that you carefully take all of the pieces off your phone, including the battery, because leaving any pieces attached can create additional problems. If you can, take advantage of a warranty repair that’s awesome. But most of the times, water damage repair isn’t covered by your warranty.

Removing moisture from your phone’s internal components isn’t as difficult as it may seem. We’ve all experienced that sinking feeling when we drop our phone in the toilet or sink, but there are ways to remove moisture safely. Removing moisture from your phone will help remove condensation that causes your phone to fog up.

If you frequently experience this problem, removing moisture regularly will help minimize it. Just dry your phone with rice or hair drier or silica gel.

You can try using a vacuum on your phone to get water droplets or moisture from the phone. Keep your hand on the cup to create a suction cup around the end of the hose and keep it near the battery port, SIM card slot, and the audio jack,, which will suck out the water under the screen.

Uncooked, dry rice is amazing for absorbing moisture and drying out your smartphone from the inside out. To do this, keep all the removable pieces you removed and bury the smartphone in enough rice to cover it from the top and bottom. After this, place your smartphone and the rice in an air-tight container to ensure that the rice absorbs moisture from the phone and not from the surrounding air in the room.

Leave the telephone inside the rice for at least a day or two before taking it out. You can also wrap the phone in a thin layer of water-absorbent cloth to prevent the rice grains from getting inside the SIM card slots. If you still notice a water spot on the phone screen, move on to the next method.

Another method you can try to draw out the moisture is using silica gel packs bundled inside some cereals and chewing gum packs. They are designed to absorb ambient moisture inside the container to prevent it from going bad. You can buy these packs online, which are quite useful in many situations like this.

These silica packs are similar to the packets you use to dry out damp clothes: the gel pack absorbs the moisture, helping everything that touches get dry quickly. Silica gel is a porous, absorbent material that’s commonly used in science experiments to absorb liquids, and phone users will be happy to know there’s a way to use this dry-aging technology to keep your phone charged.

Now all you need to do is get a container and put your phone in with the SIM card tray removed and any other removable parts, along with a couple of packets of silica gel. After this, seal the container, so it doesn’t absorb moisture from the air.

If you still notice water under the phone screen or do not have access to silica gel packs or rice. Then, the only other thing you can try is to leave your phone by a window on a warm sunny day, or you can even use a desk lamp. These heat sources should eventually cause the eater or moisture trapped inside your phone to evaporate slowly.

However, this can take anywhere from a couple of days to almost a week, depending on how much water is trapped underneath your display. You also need to be careful about how much heat you’re exposing your phone to, as a lot of heat can damage the internal components of the phone.

After your phone has had ample time to dry out, try turning it back on, and it should power on if there hasn’t been any damage to the internals. You might notice certain mineral deposits or water marks where the water was underneath the screen. These can be cleaned out using isopropyl alcohol. Using isopropyl alcohol is important as it will not leave any residue and absorb any lingering moisture; it does not conduct electricity and dries very fast.

Despite seeming counterproductive, using isopropyl alcohol on the phone screen can be the solution as it does not conduct electricity. It will dry off any moisture and water when the phone is taken out to dry off.

That’s it for this article, folks; now you know what to do if you have screen damage from water or if there’s water inside the phone’s screen. Most of the time, the solutions mentioned here should be enough to draw out any moisture from the phone.

However, dunking your phone in rice after there’s been physical damage to the phone due to the water will not do anything. In such cases, you need to go to a service center to fix your phone.

Your LCD computer screen or any other LCD Display can get ruined due to water damage. If water in laptop screen is visible in the display or even you have a hint of suspicion that water has penetrated your screen then take action immediately because leaving moisture unattended in the laptop screen will surely cause permanent damage. If you remove the moisture quickly then your screen and the entire system have a chance to recover and return to normal display by resuming its operations.

When moisture is detected on your computer and specifically in the LCD screen then you need to unplug your power cord and shut down your computer. Your computer will short which may cause serious damage if the water creeps into the live circuit. Remove the battery completely from the laptop or remove all the cord connects from the monitor display after the power is turned off when you shut down your laptop. Then take a paper towel to blot the keyboard by absorbing water from the screen exterior. To prevent it from working into the computer remove as much water from the exterior as possible. Then place the laptop next to your fan so as to encourage evaporation while you prepare for the next step.

We recommend that you purchase a large bag of rice by adding rice to a storage bin, bucket, or any dry plastic container that is large enough to accommodate the computer with the rice combined. Then fill half of the bin to start by setting the entire laptop or the LCD monitor on the rice and add more rice until it is completely covered, then seal the container. Here the type of rice is not important as you can use any type of rice whichever is least expensive. The rice creates an ultra-dry environment by absorbing the water. The rice pulls away from the moisture by drying out your LCD screen’s water damage. This works for most of the electronic devices in which water has entered. We recommend that you leave the screen in the rice for full 24 hours. Then pull out the screen by wiping away any residue from the rice with a soft cloth to avoid any scratches on the screen.

By now ideally, the rice must have absorbed your laptop screen water cloud or other LCD water display issue. Then after cleaning the screen replace the battery or cords and reconnect the power. Then turn on the laptop unit to test the screen. You need to watch for any flickering or any odd behavior which indicates that water is still present. If the laptop screen is performing normally then it indicates that the water is removed. If the problem still persists then return it to the rice bin by leaving the unit submerged in dry rice for several days. This process works, however, it works slowly. You can also use the kitty litter method by absorbing the moisture in case the rice method fails. The litter method is used to grab moisture by holding it in clumps. In an extreme case, you need to buy silica gel packets like those found in shoeboxes which will also work for repairing LCD screens having water damage.

Here is theConclusion abouthow to remove water from lcd screen -We hope this blog will be useful for our laptop users who find it difficult to repairLCD Screen Water Damage.

Laptop screen water damage is a common problem. It can happen when you spill liquid or food on the laptop. It may also occur if you accidentally spill water on your laptop while it"s being used outdoors or in a wet room. If the damage isn"t quickly cleaned, it can lead to permanent loss of data and/or hardware failure.

There are many causes of laptop screen water damage,but most are preventable. The following tips will help keep your laptop safe from accidental spills and other water-related accidents:

Avoid spilling liquids directly onto the keyboard. Instead, try to clean off any spills immediately with a cloth or paper towel before they cause damage.

If you accidentally spill something on your laptop screen, don"t panic. You can still salvage the plastic cover and get it clean with a little effort. Simply use your vacuum cleaner to suck up any water that has managed to penetrate the cover. If there is any liquid left behind, you can use a soft cloth or paper towel dampened in rubbing alcohol to wipe it away. Be sure not to use anything abrasive as this can scratch the screen.

You also need to be careful about blowing air directly at the screen if you want it to stay dry. Blowing air directly across the computer"s surface can create static electricity that causes damage over time. Instead, place some towels over areas of your laptop"s case where there may be liquid present and blow across them gently with a fan turned off or on low power (keep in mind that this will also help with dust).

The most common reason for water in monitor screenis a broken seal around the monitor. The seals are plastic or rubberized strips that keep dirt and dust from getting inside of your monitor. When these seals break, they can cause water to leak into your computer.

2. Unscrew the screws holding down one side of the case and remove it completely from your computer case (or take off all screws holding down both sides).

3. Remove any cables connecting other parts of your computer system (such as hard drives) to make sure they aren"t plugged into anything that may be causing a problem (e.g., AC adapter for power supply or USB cable for DVD drive).

Maybe the apartment above yours has sprung a water leak. Or perhaps your teen tripped in the living room, spilling soda all over the TV. Either way, now your TV is wet, and it’s not working like it used to. Learn what to do if your TV got wet and how to know when it’s time to shop for a new one.

A small spill or minimal condensation on your TV may not cause irreparable damage as long as the water doesn’t reach the primary power sources. But even just a small amount of water on the circuit board can lead to permanent TV damage and short-circuiting.

Start by unplugging the TV. Then, wipe up the water with a non-abrasive cloth to avoid scratching your screen. Give your TV plenty of time to dry, and ensure that every drop of water has been wiped up so that it doesn’t soak into your television.

If your TV has sustained heavy water damage, it’s likely beyond repair, and you may need to replace or upgrade your television. However, any attempted repairs should be done by a professional.

Allow your TV to fully dry and have it inspected by a certified technician. A professional will be better equipped when determining the extent of the damage. Taking your television apart yourself could put you at risk of serious injury and may void the warranty. It’s always best to check your TV manufacturer’s warranty information before having any repair work done.

If you have a water-damaged TV screen, you’ll likely know pretty quickly once you’ve turned it on. A water-damaged LCD screen is usually not repairable, as water can settle between the layers of the liquid crystal display and can be very difficult to dry. In this situation, consider replacing your water-damaged TV with a new one.

Your TV’s remote control may be a little more forgiving of water damage than your television. If you’ve spilled water on your remote, quickly remove the battery cover and batteries. Then, use a soft, non-abrasive cloth to wipe all the water off the remote. If the water spill was minimal and doesn’t appear to have gotten inside, wiping it and setting it out to dry should be enough.

If there was a big spill or the remote was submerged in water, it likely has internal water damage, making it less likely to continue working. Remove the battery cover and batteries, wipe the remote down, and place the remote in a zip-top bag filled with dry rice. Let the remote sit for 1-2 days before removing.

Replacing a water-damaged TV remote may not be as big of a deal with tons of universal and replacement remotes available. But a water-damaged TV is a different story!

Luckily, Rent-A-Center makes it easy to bring home a new TV that can even outperform your old one! Rent-to-own today’s top TV brands like Samsung and LG, select the perfect sized TV for your space, and bring your new TV home same-day! Visit a Rent-A-Center location near you, and browse your local selection today!

Unfortunately it could be power related or component related....all modern TV sets are modular in design...which basically means each panel does a set job...and if a component blows...then the engineer "swaps " that module ...because it is easier than trying to detect and replace very tiny components.

My guess it is the video board which is sometimes separate but usually on the main board.I assume you have dried ...cleaned and reseated ALL the connections....and looked around the board for signs of burnt areas, or browning....

A tv engineer would be my next thought ..but if you are adept at fixing things ..Take the model number ...and search eBay and Amazon for the main logic board....they are usually inexpensive...

Have a desk fan blow directly at it for 7 days. Then, buy some tools, and then open the lcd screen to see if it"s completely dry. If not, repeat the process, but this time, don"t buy tools because you already have.

Get a sponge from your kitchen(of course you have one) and buy some tools to open lcd screen. Then, open the lcd screen, and then you have to try to use the sponge, soak as much water as you can. Try not to touch the battery, or else you"ll get electrocuted and that can hurt your skin tremendously. If needed, repeat the process, but this time you don"t have to buy tools because you have.

For this suggestion, get a 1000 Watt hairdryer. If you have a lot of water on the lcd, and they won"t get away(it"s mostly sticky stuff with little water), use high heat, at 212 F, to evaporate the water. But then the sticky stuff will still be left behind. Get a can of water, and try to put just the right amount of water to rinse the glue off(It"s hard, too little will leave glue, too much will need to repeat the process again). Then try to examine the motherboard with a see-through lens, which can see through objects. This can lead to overheating. Make sure the CPU is under 100 F.

Open the screen in the computer, set your dehumidifier to at least 122 F. Make sure the dehumidifier points directly to the screen. This will soak the water out, but this can overheat the CPU, so make sure the CPU temperature is 100 F or less. If it hides really close to getting in the screen, set the dehumidifier very close, around 6 inches away or less, but that could burn your monitor.

Yesterday I accidentally spilled some water over my 22 inch LCD Dell Monitor’s Screen and after 15 minutes I saw small black portion at the mid bottom of my screen and it keeps on expanding.

When it comes to taking care of your computer monitor, you want to make sure you are using the right cleaning products and techniques. One commonly asked question is whether it is possible to clean a monitor with water and a coffee filter. While these items can be used to wipe away dirt and dust, it is important to understand the risks and how to use them safely to protect your monitor from damage. This article will discuss the potential benefits and drawbacks of using water and a coffee filter to clean your monitor, as well as the importance of following manufacturer instructions when cleaning your monitor.

If you have simple dustings, use compressed air (the same stuff you use to knock dust out of your case fans), followed by a quick dry wipe down. Microfiber cloths are your best friend when it comes to cleaning.

Surface PC monitors with rubbing alcohol to moisten a microfiber cloth. It is best to use wet towels rather than dripping wet towels. Wipe the moistened cloth in one direction from top to bottom, as directed. The surface should be allowed to dry completely before plugging it back in.

Because coffee filters are lint-free and do not scratch your LCD TV screen, they are the best tool for keeping it clean. After turning off your TV, gently wipe the dry coffee filter across the screen with a sweeping motion to remove any dust from it.

TV screens, in short, act as honey pots for dust, dirt, and finger streaks. A delicate screen is now present on LCD, LED, PLASMA, and OLED TVs. With the advances in technology over the last few decades, it is possible that they will no longer be able to tolerate the hard-to-clean methods used to create CRT glass television screens from the 1960s to the early 2000s. Vaseline, as well as other petroleum jelly brands, may be effective in this case. A scratch on your LCD screen can be a sign that you need to get an lcd scratch repair kit. If your screen is not flat, a dedicated multi-purpose screen cleaner or wipe is ideal.

It is critical to maintain your TV in good condition, but it is also critical to use the proper cleaning products in order not to damage your expensive electronics. If you’re cleaning your TV, make sure you have a soft, dry microfiber cloth or an electrostatic duster like a Swiffer or a GH Seal. A pre-moistened wipe designed specifically for electronics will remove the stubborn residue if you find a stubborn residue. If you use a baby wipe, the residue left behind on an LED TV screen can be permanently damaged. Finally, to remove dust that may have accumulated in the vents, clean the TV’s buttons and back. This will ensure that your television stays looking good and functioning properly.

If you want to clean the frame or screen of your TV in general, a soft, clean, lint-free, dry cloth is recommended. Microfiber cloths are the best. It is never a good idea to use window cleaner, soap, scouring powder, or any other solvents containing alcohol, benzene, ammonia, or paint thinner.

It is not recommended to use white vinegar to clean a TV screen, despite its ability to clean a television. It is a corrosive liquid that can scratch the delicate surface of a television screen. Damage to the anti-reflective and anti-glare coating, for example, can cause irreversible damage to the image. Caviness is another concern because vinegar can cause streaks and discolored patches on the surface. Vinegar can permanently etch the surface of the screen, resulting in a foggy, distorted image. You should avoid using vinegar while cleaning your TV screen as a result. Instead, clean the floor with a dry microfiber cloth or a soft cloth dampened with distilled water to remove dust and dirt. It is possible to remove tough stains with a few drops of mild detergent and warm water. You should always use a clean cloth after cleaning your screen, and avoid using chemicals or abrasive materials. It is critical to invest the time necessary to ensure that your TV screen is in good condition for many years to come.

If you still have streaks or stains on the microfiber cloth, wash it with distilled water and wring it out until it is almost dry. Wipe the cloth across the screen vigorously in broad motion with very little pressure until you reach the bottom of the screen.

If you want to clean your monitor, make sure you’re using a soft microfiber cloth and distilled or still water. Mineral deposits on the surface of the screen can occur in other types of water.

Cleaning fluids specifically designed for computer monitors are available on the market. The most common method for cleaning monitors is to use distilled water, which can also be combined with white vinegar to remove stubborn stains. Keep paper towels, rags, old T-shirts, and any other commonly used cleaning tools away from your home. There are gentle cleaning fluids designed specifically for monitors, but distilled water works well as well as the others. Tap water contains minerals and other substances that can damage the screen or cause streaks to appear. Water should be liberally sprayed with white vinegar to deal with the most stubborn of grime. It is critical to avoid spilling it on your laptop.

In terms of cleaning LCD screens, there are several steps you should take to ensure their safety and proper maintenance. Remove any dust from the screen with a microfiber cloth before beginning. If you have fingerprints or are experiencing smudges, spray 70% isopropyl alcohol onto a cloth, or use a pre-moistened alcohol wipe or a Clorox Disinfecting Wipe to clean non-porous surfaces, such as the screen, without bleach. If stains persist, you can gently clean the screen with distilled water and lightly dampen the cloth. To avoid wetting the screen, spray the cleaning solution on the cloth and wipe it clean of any excess liquid. Windex should only be used as a cleaner if your laptop’s screen is glass. It is never a good idea to direct-paint a computer display, as this may lead to oversaturating of the pixels or component failures if water leaks into the set’s inner workings.

It is critical to unplug your device before turning it off. Once the dust has been removed, you can start cleaning your screen with a microfiber cloth. It is safe to use 70% isopropyl alcohol, or spray it onto a cloth or a pre-moistened alcohol wipe, to clean non-porous surfaces such as screens without using bleach, and it does not harm your skin.

If your monitor becomes covered in grime, your productivity and health will suffer. There are several steps you must take to keep your LCD screens clean and happy. We’ll show you how to clean laptop screen frames without scratching or damaging them. Finally, we discover which commercial cleaning kits are well worth the money and effort you put into them. The best way to clean car windshields is with glass cleaner spray, but it will melt LCD monitors’ coatings. Pinchers and cotton swabs can be used to clean the crevices around buttons and other difficult-to-reach places. As a result, you should never use tap water to clean your home because mineral deposits may accumulate.

Ethic alcohol or rubbing alcohol are not suitable for cleaning computer monitor screens. Instead, we’ve made a fantastic DIY screen cleaner recipe using diluted vinegar that you can make at home. This recipe will also work for cleaning dirty eyeglasses if you are looking for a simple and easy way to do so. When you scratch your monitor on a regular basis, it may appear dull; however, if it scratches significantly, it may appear damaged. Using petroleum jelly to remove small scratches is an effective way to do so. If you use petroleum jelly on your scuff marks, you will be permanently discoloring them. When you’re finished with your monitors, they’ll look great in showrooms.

A gentle abrasive in baking soda helps to remove small scratches without causing too much damage to the surrounding surface. Before using this fix on large areas, it is critical to test it on a small area. Our guide will walk you through the most effective methods for cleaning your computer monitor’s screen to make it look brand new once more.

You should never use Windex to clean a monitor. The material is made of glass, but it can be harsh for delicate computer screens. Furthermore, eyeglass cleaners should be avoided because they will not disinfect the screen. When cleaning the screen, use a dry cloth that will remove particles and germs. It is also important to note that window cleaners, household cleaners, aerosol sprays, solvents, ammonia, abrasive cleaners, or cleaners containing hydrogen peroxide should not be used on the screen. Furthermore, do not use the cleaning product directly on the screen, as it may cause damage. As a result, using a dry cloth to clean a monitor is the simplest method.

However, because tap water contains minerals and other substances that can harm the screen or leave streaks on it, it’s best to use filtered or distilled water instead. If the water becomes extremely stubborn, apply a pinch of white vinegar.

The differences between a computer monitor and how it should be cleaned do not have to be stark. If you’re a regular user of the monitor, you’ll be able to keep it clean on a regular basis. If the monitor is not turned on, it is possible to cause an electrical shock. Furthermore, a black screen makes it easier to see dust and scratches. Before you can clean your laptop or monitor, make sure that it is completely turned off. Meg MacDonald’s poem, The Spruce Smudges should be removed. A non-glass-coated screen (LED, LCD) can only be touched with a small amount of force. Wipe only the areas that have been stained with gentle pressure.

A computer monitor can be easily contaminated with fingerprints, dust, and dirt. To begin, clean it with a microfiber cloth that has been thoroughly wiped down. If you need to remove fingerprints and smudges, use 70% isopropyl alcohol on a cloth or a pre-moistened alcohol wipe or Clorox Disinfecting Wipe, both of which are excellent options for non-porous surfaces. If your screen needs something strong, you can combine 1 cup distilled water and 4 cup white vinegar in a spray bottle, but distilled water is the best and safest cleaner. If you need to clean your computer monitor, never use bleach.

JUMP! ®, JUMP on Demand®, and Trade-In devices with damage will be assessed at a lower value or require a fee. See your program terms & conditions for details.

The warehouse will check the device condition when we receive it. If it’s damaged, you may receive a reduced trade-in value or be required to pay a fee on your bill statement. (Prepaid customers will have the defective device shipped back instead.)

When inspecting a screen, remove any screen protectors and cases first. Tilt the device under good lighting conditions and inspect it at multiple angles. Screen damage includes hairline cracks that are difficult to see.

Mobile devices have a Liquid Damage Indicator (LDI) to show if the device has contacted any liquids. The indicator is white when it"s new, and it turns pink or red when it contacts water.

Wearables like Apple & Samsung watches often don"t have visible LDIs. Check for moisture under the display screen, as well as corrosion, discoloration, and fuzzy growth on the charging connection.

If the device does not fully turn on and load the home screen or if it cannot stay on without being connected to a charger, it"s considered not able to turn on.

No matter how careful you are, accidents happen. Screen damage and liquid damage are not covered under the warranty, so T-Mobile can"t exchange devices with this damage. But, we don’t want you to be stuck with a broken phone, so you have two options to replace or repair your damaged device:

Before visiting a T-Mobile Store, please file a claim with Assurant, our Protection and Repair vendor. This will expedite your repair process and minimize your time in the store. Below are two convenient ways to file a claim.

Once the claim is filed, be sure to schedule an Assurant Repair appointment at one of our T-Mobile Device Service Locations via the text message or confirmation email sent from Assurant.

DIGITAL CALIPER- Can measure inside, outside, depth and step measurements up to 6 inches/150mm with a resolution of 0.0005" (0.01mm), accuracy of 0.001" (0.02mm)

This remote LCD reader can be wired to most any brand industry standard encoder output meter. Tapping on the gold target sends a signal to the meter to display the current reading. The meter reading displays for 10 seconds, then the meter serial number displays for 10 seconds, then it goes blank until tapped again. This display can be used with most 3-wired encoded output meters using AWWA protocol UI-1203 (Sensus Protocol)

Wire is not included. If your encoder does not have a wire lead, you will need to add 3 conductor cable. We have extra cable available in other listings, or call us for custom lengths.

We may have more of this item in stock than shown. Please contact us if you need more units. This item may be ordered when out of stock and we will fill your backorder when restocked (usually 10-14 days).

Once you have found the correct part number, see HP Consumer Notebook PCs - Ordering HP certified replacement parts. Use the instructions in this document to order a replacement part.

Whether it fell out of your pocket while standing on a dock or got left out in the rain, it’s obvious that cell phones and water don’t mix. And while some new phones are marketed as being “water-resistant”, it is still a smart idea to keep your phone away from water whenever possible. There are a number of different issues that can arise if your phone has been subjected to water damage, from blurry photos and muffled audio to being unable to charge to not functioning altogether. While you might think that the only solution to these issues is to get an entirely new phone, there is a chance that your phone can be repaired.

If your cell phone has taken a swim or you suspect it has come into contact with water at some point, there are a few different things you can do to determine whether it has sustained any water damage. Many phone manufacturers keep water damage in mind when they design their phones and often place a liquid contact/damage indicator strip located inside the SIM card tray. This provides an easy way to check for water damage but often means that if the strip indicates that it’s been in contact with water, you will be ineligible for a manufacturer warranty.

While some encounters with water may leave your phone completely fried, sometimes all that is required is a single part repair, such as a battery, screen or speaker. Because each device reacts differently to water damage, we offer free estimates, so you can find out exactly what the cost of repairing your phone would be before any repairs begin. It’s important to bring your phone in for repair as soon as possible to avoid the water causing any major damage.

When it comes to drying out a water-logged phone, patience is key. The first thing you’ll want to do is remove it from the liquid immediately. Next, you’re going to want to turn it off and leave it off. This is going to help prevent any liquid inside the phone from interacting with any running electronic components. It’s important that you don’t continue to use your phone after it’s sustained any water damage. After turning your phone off, you’re going to want to pull off the case and if possible, remove the battery, SIM card and microSD card.

You might have heard that burying your phone in rice can help absorb some of the water, but this method isn’t very effective. Instead, silica gel from packets you often receive with new items such as shoes is much more effective. Leave your phone in the silica gel for 24-48 hours or until it’s fully dry before you try to turn it on.

In some cases, giving your phone some time to fully dry out can be enough to solve the problem and get it working. If this isn’t the case and you start experiencing issues with certain features, such as your speakers, charging ports or camera, your phone might need some repair. That’s where Repair Express comes in! There’s no way for us to determine exactly what kind of repairs, which is why we offer free estimates. If our initial diagnostic review of your phone reveals that modular parts might need to be replaced, we will let you know before any additional expenses are incurred. Ourexperienced team of technicians put all our repairs through rigorous testing to ensure that when you receive your phone back, it is good as new!

While it can be a pain to have to hand over your phone for repairs, at Repair Express, we have the experience and expertise to get repair jobs done right and get your phone back to you as soon as possible.