3.5 inch tft lcd monitor raspberry pi quotation

Important note: The screen will be white after power on if you didn"t install the special OS. because this 3.5inch screen output videos is based on SPI interface. other OS use HDMI output by default. Recommend to use mirror which already with SPI driver or install the SPI driver in the OS to totally light the screen.

To use the LCD with the Raspberry Pi official image, driver should be installed first. However, for the first testing, you may want to use our provided image directly.

Make sure the hardware connection is correct and connects fine. Make sure the image in TF card is burnt correctly. The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.

The touch screen LCD is ready with 320×480 resolution, 50 FPS (Frame per second). Resistive touch control is being supported by the Raspberry Pi OS or Raspbian (directly-pluggable). However, we will still need to install the driver for graphic display :)

However, there is a dedicated case/enclosure and a low-profile heatsink with a fan for this LCD to fit perfectly on the Raspberry Pi 4 Model B. The case has an opening for the LCD, and the low-profile heatsink with a fan keeps the Raspberry Pi 4 Model B protected and cool! You get a perfect console :) Don"t forget to remove the top lid/cover of the enclosure for the 3.5-inch LCD.

Note: The Raspberry Pi 4 Model B, 3.5-inch Enclosure, and the Low-Profile Heatsink with a fan are NOT INCLUDED in this product, please get them separately.

As we understand, Raspberry Pi 4 Model B delivers great performance and of course, more power will generate more heat as of all CPU :) So we need a way to install an additional heatsink to dissipate the extra heat. It will be better if we can have the option to add a cooling fan for active cooling. Well, this 3.5-inch touch screen LCD comes ready with the heatsink and cooling fan for you to use with the Raspberry Pi 4 Model B. it solves all the concerns.

The 3.5-inch touch screen uses the GPIO on the Raspberry Pi board, so it stretches out 2 pins as the power to supply the cooling fan on the low profile heatsink, and keep the Raspberry Pi board cool!

Note: The Raspberry Pi 4 Model B, 3.5-inch Enclosure, and the Low-Profile Heatsink with a fan are NOT INCLUDED in this product, please get them separately.

The Graphic driver is provided and can be downloaded for Raspberry Pi OS/Raspbian. It also supports Ubuntu and Kali Linux. Do follow the steps here: http://www.lcdwiki.com/MHS-3.5inch_RPi_Display

Note: Please use the recommended system for the touch screen. If another system is used, it may not have the touch function or may not work. You need to configure it yourself. Because there are many systems that the Raspberry Pi can use, we can’t make every system compatible with the touch screen.

This small 3.5 inch touch screen Raspberry Pi Display module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi and an ideal alternative solution for HDMI monitors. The screen also comes with a stylus to interact with the small screen.

While googling for any info about lcd controller I came across this page: http://heikki.virekunnas.fi/2015/raspberry-pi-tft/, author managed to get from manufacturer patch file for kernel sources and tested it with 4.1.y - on which lcd worked. But still LCD replace HDMI, but I want to use this screen as additional for user interaction, while the bigger on HDMI as presentation monitor.

Since, fbtft has been merged with rpi kernel, so the fb drivers (including ili9341.c) was moved to fbtft_device driver (so the author of page can"t compile latest kernel with driver+patch).

So something about hardware, which I reverse engineered by the "hard way" - "grab multimeter and run through all LCD FPC pins and shift register pins"

Now I noticed there is "9486L" which can suggest that LCD screen is controlled by ILI9486L, I found this LCD on taobao too but I can"t contact seller.

I"m pretty sure about D/C (Pin 37 on LCD) and Reset (Pin 19 on LCD) pins by looking into driver code, but I can"t identify other signals (WR/RD/CS/etc...)

[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0x2938b030 smsc95xx.macaddr=B8:27:EB:38:B0:30 bcm2708_fb.fbswap=1 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait

- Controller is not ILI9341/ILI9325 - those are for smaller displays (320x240, etc...), I guess this might be ILI9486/9488 because they are for 480x320 displays. But when I compared init with DS it does not fit right so LCD can have a clone of ILI9486/9488 ...

- Module use only SPI interface and two CE signals (CE0 for touch controller, CE1 for LCD shift registers - compared to others lcd modules, in KeDei module this is swapped),

All the accessories listed below tier pricing need to pay.We won"t deliver until you select. Power adaptor should be 5V/2000mA in output and center pin for positive voltage and the outer shield for negative voltage .The temperature for controller RTD2660 would increase during working.That"s normal phenomenon,not quality problem.

ER-TFTV070A1-3 is 800x480 dots 7" color tft lcd module display with small HDMI signal driver board and superior display quality,super wide view angle. It"s optional for optional 4-wire resistive touch panel with USB driver board and cable, optional capacitive touch panel with USB controller board and cable, optional remote control,It can be used in any embedded systems,car,industrial device,security and hand-held equipment which requires display in high quality and colorful video.It"s also ideal for Raspberry PI by HDMI.

It is the cutest display for the Raspberry Pi. It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay. It"s designed to fit nicely not only to the Pi Model A or B but also works perfectly fine with the Model B+/2B/3B/4B.

*When working with Raspberry Pi 4, for the system image of Raspberry Pi after 2021-10-30, for example on Bullseye, please modify "dtoverlay = vc4-kms-v3d" to "dtoverlay = vc4-fkms-v3d" in the config file, otherwise it may fail to start. But on Buster, please comment out "dtoverlay = vc4-fkms-V3D" by adding #.

This 3.5-inch touch screen is the same size as the standard Raspberry Pi model B/B+, and well mates with the Raspberry Pi boards. With its touch screen and split audio from the HDMI input, it is ideal for portable devices and multimedia projects, and it is a replacement for a heavy and bulky HDMI monitor, keyboard and mice.

3.5-inch TFT LCD display with casedesigned for Raspberry Pi. The display with a resolution of 320x480 px is equipped with a resistive touch screen. Supports 125MHz SPI signal inputs with a refresh rate of up to 60fps when running Raspberry Pi - higher than most similar products, making it ideal for playing games and videos. The included acrylic case is adapted to the screen and the Raspberry Pi 4B/3B/B+, with easy access to all ports.

This small 3.5-inch touch screen module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi. The screen also comes with a stylus to interact with the small screen.