flash firmware onto a v56 lcd panel driver board pricelist

By continuing to use AliExpress you accept our use of cookies (view more on our Privacy Policy). You can adjust your Cookie Preferences at the bottom of this page.

This model is universal Controller 3663 gives the opportunity to build on the base of the laptop or monitor matrix full multimedia TV C T-2 tuner on board without depriving themselves of the opportunity of using it as a monitor.

Controller 3663 has on board analog-to-digital Touraine Rafael R842 with support for T-2, DVB-T, DVB-C, ATV, by just saying support for more digital signal cable, teletext and radio TV. As main chip has allowed not only to exploit the full potential of the TV chip, but not deprived of the possibility of reproducing a photo, video, audio files from a USB drive. All the innovations introduced in this model is made possible by the use of a more powerful master chip.

Suitable for Europe, Africa, The five Central Asian countries, the Middle East, Russia, Thailand, Myanmar, Kenya, Portugal, Malta, Uganda and other countries or regions.

OSD Language: Russian, English, Czech, France, Magyar, Polski, Dansk, Espanol, Hrvatski, Nederlands, Deutsch, Italliano, Norsk, Portugues, Suomi, Svenska, Arabic, etc. (more pls check the video)

2.After turn on the power ,the light of the 7key button will be Red then flash red and blue.after about 1 minute, the light stop flashing ,it means upgrade has finished.(Note that write programs do not power outages, crashing won"t be able to use)

This controller was tested and works well with aerial TV, receiving well digital broadcasting (MPEG4) and analog using a piece of wire as antenna. That prove of good sensitivity of TV tuner. With dedicated antena, picture quality is excellent.

For those who want to play more with controller, please notice that in order to enter into "service menu" mode - first press on remote control "input" button and then press the code 2 5 8 0 .

Newer boards 3663 are not compatible with 7 key keyboards, so needs to exchange wires in socket to be compatible or buy ready made 7key-board for 3663.

Programming is very simple, we must choose proper .bin file and copy it to USB pen-drive at root directory, plug pen-drive into USB, then plug power cord, status LED will made some flashes, first slower and at end faster, and software upgrade is done, you will see picture on LCD screen.

Attention: Sometimes, when playing with firmware, if there be power cut/brake during programming and flash will not finish programming, than the board become dead.

After all done, use the remote control to turn on the tv (after burning the firmware, the mainbaord is on standby, need the remote control to turn on the tv)

LCD panels of broken laptops or old TVs can easily be turned into multifunctional displays. You can give them analog and digital inputs and media player capabilities with a cheap universal controller board. As long as the panel itself is functional, you can use the V56 controller board to drive both the screen and the backlight. Reuse LCD screens as media players, video monitors or computer displays and save them from the garbage dump!

The easiest way to repurpose your LCD panel is by using a V56 controller kit that comes with all the parts that you need. I tested the V56 Universal LCD TV Controller Driver Board from Banggood It supports most LVDS panels with resolutions up to 1920 x 1080 pixels.  It comes with the following parts:

First of all, remove the LCD screen from its housing. In my case, it was an old laptop screen, so I detached the lid from the laptop and removed the plastic housing from the screen.

According to the specifications you looked up in the previous step, you need to set the voltage jumper on the controller board. There are 3 options: 3.3 volts, 5 volts and 12 volts. Make sure you set the right voltage, or else the magic smoke might escape!

Look for the file that matches your screen’s model number and resolution. If the model is not listed, then choose the “general” type for that resolution

The power LED should be blinking BLUE for a couple of times while it’s loading the new firmware. If it doesn’t upload the firmware, you should try renaming the file from “LAMV45R.bin” to “LAMV56.bin” (remove the R)