flash firmware onto a v56 lcd panel driver board quotation

By continuing to use AliExpress you accept our use of cookies (view more on our Privacy Policy). You can adjust your Cookie Preferences at the bottom of this page.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

You can basically use any universal LCD controller board. I use a V56 or a V53 LCD controller board. You can flash its firmware via a USB flash drive. However, if you’re planning on using a PIR-sensor then you’ll also have to add a relay because it won’t go into standby mode. Instead it will complain about “No Signal”.

One like this is very cheap and can be configured by a set of jumpers. Drawback is it only has a VGA port. So you’ll need an additional VGA-to-HDMI-adapter. However, the cheapest will do.

Note: Since the driver board model is updated frequently, the appearance and chip will be different, please refer to the actual received. If you mind this, please buy carefully.

1. This product is compatible with most models. Customers only need to confirm that the LCD screen is compatible with the following resolutions, without repeating the inquiry model. (Firmware burns the corresponding resolution)

2. This product needs to burn the firmware by yourself before it can be used. If you don"t know how to burn the firmware, unfortunately, it is recommended not to buy. Thank you for your understanding.

3. This kit comes with a 1ch 6bit 30pins screen cable by default. If it is not compatible with your screen, please purchase a matching screen cable separately.

4. Be sure to use the correct power supply. If the current is too low/too high, it will fail to boot, or even burn out the chip and damage the motherboard.

Burning method: to record the screen program in the USB flash disk, USB flash disk inserted into board, plug in the keypad, electricity; About after a few seconds, press the keypad lights start alternating red and green flash, flash lights began to write programs (please do not power), light in the slow flash first, after a slow flash flash, will speed up the quick flash, long after the last until the lights stop flashing light is the program written, electricity burn with USB flash disk to complete the program.

Not only USB interface can be used to upgrade programs, but also can use to play video, basically formats are supported. You can also set a boot display pictures or LOGO

UpdateModel:T.SK105A.03 (Update from November, 2020) The specific model is mainly based on the received model, pay attention to burning the corresponding model firmware.

Not only USB interface can be used to upgrade programs, but also can use to play video/music/photo, basically, formats are supported. You can also set a boot display pictures or LOGO and Mirror Enable.

IT KEEPS flashing and NEVER STOP. it"s normal, just wait about 1 minute, it means upgrade has finished. then power off and pull off the u-disk. (Note that write programs do not power outages, crashing won"t be able to use)

A2: Download this software and re-upgrade. If your 105 chip is unable to be upgraded, you can change the upgrade name to "UTS6710_sos" to force the upgrade. >>>http://myosuploads3.banggood.com/products/20210202/20210202043110UTS6710.rar<<<

Note: Since the driver board model is updated frequently, the appearance and chip will be different, please refer to the actual received. If you mind this, please buy carefully.

1. This product is compatible with most models. Customers only need to confirm that the LCD screen is compatible with the following resolutions, without repeating the inquiry model. (Firmware burns the corresponding resolution)

2. This product needs to burn the firmware by yourself before it can be used. If you don"t know how to burn the firmware, unfortunately, it is recommended not to buy. Thank you for your understanding.

3. This kit comes with a 1ch 6bit 30pins screen cable by default. If it is not compatible with your screen, please purchase a matching screen cable separately.

4. Be sure to use the correct power supply. If the current is too low/too high, it will fail to boot, or even burn out the chip and damage the motherboard.

Burning method: to record the screen program in the USB flash disk, USB flash disk inserted into board, plug in the keypad, electricity; About after a few seconds, press the keypad lights start alternating red and green flash, flash lights began to write programs (please do not power), light in the slow flash first, after a slow flash flash, will speed up the quick flash, long after the last until the lights stop flashing light is the program written, electricity burn with USB flash disk to complete the program.

Not only USB interface can be used to upgrade programs, but also can use to play video, basically formats are supported. You can also set a boot display pictures or LOGO

UpdateModel:T.SK105A.03 (Update from November, 2020) The specific model is mainly based on the received model, pay attention to burning the corresponding model firmware.

Not only USB interface can be used to upgrade programs, but also can use to play video/music/photo, basically, formats are supported. You can also set a boot display pictures or LOGO and Mirror Enable.

IT KEEPS flashing and NEVER STOP. it"s normal, just wait about 1 minute, it means upgrade has finished. then power off and pull off the u-disk. (Note that write programs do not power outages, crashing won"t be able to use)

A2: Download this software and re-upgrade. If your 105 chip is unable to be upgraded, you can change the upgrade name to "UTS6710_sos" to force the upgrade. >>>http://myosuploads3.banggood.com/products/20210202/20210202043110UTS6710.rar<<<

CNDis the best choice for LCD / LED main board solutions, and Open frame Touch Monitor Solutions, Android board Solutions, with over 12 years professional experiences both in hardware and software design, we provide one-stand services for both hardware and software. and CND has gained very good reputation during cooperation with biggest clients from financial , rail transit, and industrial etc.Quality is our culture, Time is gold, Service is our soul, to be with us your business is safe, your money is safechoose CND, choose a mutual win-win partner.

LCD panels of broken laptops or old TVs can easily be turned into multifunctional displays. You can give them analog and digital inputs and media player capabilities with a cheap universal controller board. As long as the panel itself is functional, you can use the V56 controller board to drive both the screen and the backlight. Reuse LCD screens as media players, video monitors or computer displays and save them from the garbage dump!

The easiest way to repurpose your LCD panel is by using a V56 controller kit that comes with all the parts that you need. I tested the V56 Universal LCD TV Controller Driver Board from Banggood It supports most LVDS panels with resolutions up to 1920 x 1080 pixels.  It comes with the following parts:

First of all, remove the LCD screen from its housing. In my case, it was an old laptop screen, so I detached the lid from the laptop and removed the plastic housing from the screen.

According to the specifications you looked up in the previous step, you need to set the voltage jumper on the controller board. There are 3 options: 3.3 volts, 5 volts and 12 volts. Make sure you set the right voltage, or else the magic smoke might escape!

Look for the file that matches your screen’s model number and resolution. If the model is not listed, then choose the “general” type for that resolution

The power LED should be blinking BLUE for a couple of times while it’s loading the new firmware. If it doesn’t upload the firmware, you should try renaming the file from “LAMV45R.bin” to “LAMV56.bin” (remove the R)

Burning method: to record the screen program in the USB flash disk, USB flash disk inserted into board, plug in the keypad, electricity; About after a few seconds, press the keypad lights start alternating red and green flash, flash lights began to write programs (please do not power), light in the slow flash first, after a slow flash flash, will speed up the quick flash, long after the last until the lights stop flashing light is the program written, electricity burn with USB flash disk to complete the program.

Not only USB interface can be used to upgrade programs, but also can use to play video, basically formats are supported. You can also set a boot display pictures or LOGO

3. Connected to the keypad, electricity again, until you see by the indicator lights on the keypad after flashing in red and green, until after the indicator light flashing, unplug the power, then pull out USB Flash disk, afresh power on.(Note that write programs do not power outages, crashing won"t be able to use)

When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.

Step 2: Downlosd the file and open, find your screen resolution and screen model number.copy it to your U disc.(If you can’t find your screen model numer in the folder, you can copy anyone to try, if not suitable ,try another one)

After all done, use the remote control to turn on the tv (after burning the firmware, the mainbaord is on standby, need the remote control to turn on the tv)

However, this "new" V56, there is no support for most popular laptop"s screens, like for example: 1280x800_SI6L, 1600x900_DO6L , 1920x1080_DO6L and many more etc. etc. Anyway, there is way to made them work, for example for screen 1280x800_SI6L use firmware "1280x800" and "SI8L" and then, if still not working, in "Service Menu" change LVDS MAP value, that way screen works well as SI6L . The same can be done for other resolutions and LVDS signal types, as described

There are also signals that some new V56 controllers, rejects LAMV56.bin file and do not want to program it. In such case, add letter "R" in file name, like that - LAMV56R.bin, such file will be programmed well. This character "R" add for first time reprogramming only, after successful first time controller reprogram, you can use regular LAMV56.bin files without "R" for next screens.

So, always consider and think twice, before buy any board, choose seller fully supporting latest firmware files for his board, if he is not - simply DO NOT buy, because you will have useless piece of junk.

Programming is very simple, we must choose proper .bin file and copy it to USB pen-drive at root directory, plug pen-drive into USB, then plug power cord, status LED will made some flashes, first slower and at end faster, and software upgrade is done, you will see picture on LCD screen.

Attention: Sometimes, when playing with firmware, if there be power cut/brake during programming and flash will not finish programming, than the board become dead.

desertcart is the best online shopping platform where you can buy C&C Products V56 Universal LCD TV Controller Driver Board PC/VGA/HDMI/USB Interface from renowned brand(s). desertcart delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

desertcart ships the C&C Products V56 Universal LCD TV Controller Driver Board PC/VGA/HDMI/USB Interface to and more cities in Angola. Get unlimited free shipping in 164+ countries with desertcart Plus membership. We can deliver the C&C Products V56 Universal LCD TV Controller Driver Board PC/VGA/HDMI/USB Interface speedily without the hassle of shipping, customs or duties.

desertcart buys C&C Products V56 Universal LCD TV Controller Driver Board PC/VGA/HDMI/USB Interface directly from the authorized agents and verifies the authenticity of all the products. We have a dedicated team who specialize in quality control and efficient delivery. We also provide a free 14 days return policy along with 24/7 customer support experience.

Yes, it is absolutely safe to buy C&C Products V56 Universal LCD TV Controller Driver Board PC/VGA/HDMI/USB Interface from desertcart, which is a 100% legitimate site operating in 164 countries. Since 2014, desertcart has been delivering a wide range of products to customers and fulfilling their desires. You will find several positive reviews by desertcart customers on portals like Trustpilot, etc. The website uses an HTTPS system to safeguard all customers and protect financial details and transactions done online. The company uses the latest upgraded technologies and software systems to ensure a fair and safe shopping experience for all customers. Your details are highly secure and guarded by the company using encryption and other latest softwares and technologies.