water damaged lcd screen fix manufacturer

Your LCD computer screen or any other LCD Display can get ruined due to water damage. If water in laptop screen is visible in the display or even you have a hint of suspicion that water has penetrated your screen then take action immediately because leaving moisture unattended in the laptop screen will surely cause permanent damage. If you remove the moisture quickly then your screen and the entire system have a chance to recover and return to normal display by resuming its operations.

When moisture is detected on your computer and specifically in the LCD screen then you need to unplug your power cord and shut down your computer. Your computer will short which may cause serious damage if the water creeps into the live circuit. Remove the battery completely from the laptop or remove all the cord connects from the monitor display after the power is turned off when you shut down your laptop. Then take a paper towel to blot the keyboard by absorbing water from the screen exterior. To prevent it from working into the computer remove as much water from the exterior as possible. Then place the laptop next to your fan so as to encourage evaporation while you prepare for the next step.

We recommend that you purchase a large bag of rice by adding rice to a storage bin, bucket, or any dry plastic container that is large enough to accommodate the computer with the rice combined. Then fill half of the bin to start by setting the entire laptop or the LCD monitor on the rice and add more rice until it is completely covered, then seal the container. Here the type of rice is not important as you can use any type of rice whichever is least expensive. The rice creates an ultra-dry environment by absorbing the water. The rice pulls away from the moisture by drying out your LCD screen’s water damage. This works for most of the electronic devices in which water has entered. We recommend that you leave the screen in the rice for full 24 hours. Then pull out the screen by wiping away any residue from the rice with a soft cloth to avoid any scratches on the screen.

By now ideally, the rice must have absorbed your laptop screen water cloud or other LCD water display issue. Then after cleaning the screen replace the battery or cords and reconnect the power. Then turn on the laptop unit to test the screen. You need to watch for any flickering or any odd behavior which indicates that water is still present. If the laptop screen is performing normally then it indicates that the water is removed. If the problem still persists then return it to the rice bin by leaving the unit submerged in dry rice for several days. This process works, however, it works slowly. You can also use the kitty litter method by absorbing the moisture in case the rice method fails. The litter method is used to grab moisture by holding it in clumps. In an extreme case, you need to buy silica gel packets like those found in shoeboxes which will also work for repairing LCD screens having water damage.

Here is theConclusion abouthow to remove water from lcd screen -We hope this blog will be useful for our laptop users who find it difficult to repairLCD Screen Water Damage.

Laptop screen water damage is a common problem. It can happen when you spill liquid or food on the laptop. It may also occur if you accidentally spill water on your laptop while it"s being used outdoors or in a wet room. If the damage isn"t quickly cleaned, it can lead to permanent loss of data and/or hardware failure.

There are many causes of laptop screen water damage,but most are preventable. The following tips will help keep your laptop safe from accidental spills and other water-related accidents:

If you accidentally spill something on your laptop screen, don"t panic. You can still salvage the plastic cover and get it clean with a little effort. Simply use your vacuum cleaner to suck up any water that has managed to penetrate the cover. If there is any liquid left behind, you can use a soft cloth or paper towel dampened in rubbing alcohol to wipe it away. Be sure not to use anything abrasive as this can scratch the screen.

You also need to be careful about blowing air directly at the screen if you want it to stay dry. Blowing air directly across the computer"s surface can create static electricity that causes damage over time. Instead, place some towels over areas of your laptop"s case where there may be liquid present and blow across them gently with a fan turned off or on low power (keep in mind that this will also help with dust).

The most common reason for water in monitor screenis a broken seal around the monitor. The seals are plastic or rubberized strips that keep dirt and dust from getting inside of your monitor. When these seals break, they can cause water to leak into your computer.

I recently dropped my LG G3 into some water. It worked fine with no incident for about 2 weeks, until I started getting black flickering lines across the screen. This was also joined with the screen fading to darkness and then the screen turning off altogether. This has worsened now and it is rare to get the screen working for more than 30 secs a day.

As it responds to my touch still, I assume it is the lcd screen that is broken and not the digitiser (although I"ll replace both if I repair it). My problem is, I don"t want to spend £80ish on a new screen, to find out it is actually water damage to the motherboard which would make the repair to expensive for me. Any suggestions to determine whether it is screen damage or motherboard? And whether it is worth the rish?

Once a phone has water damage — from small spills to a full liquid plunge — there’s often no easy fix. The first step should be to check if your smartphone’s Liquid Contact Indicator has been activated. Most models, including Apple, LG and Samsung, have small visible indicators to show whether water damage has occurred. Consider peace of mind for those inevitable accidents with Verizon’s Verizon Protect or  Total Mobile Protection. Not only is your phone covered if it gets water damage, you may be eligible for a full replacement that same day.

Due to its high cost, the logic board is the only part in the device that is not included in the liquid damage service. If the logic board has been irreversibly damaged, we will not be able to repair it and you will be refunded, minus the cost of return shipping if applicable.

Absolutely. Although salt water is corrosive and can be very damaging to electronic devices, we can still attempt to repair it. Our success rate on salt water damage is lower than that of a device that has been dropped in other liquid, but there is still a good chance that it can be repaired. If we cannot repair it, we will refund you the repair cost, minus the cost of return shipping if applicable.

First and foremost, do not attempt to turn the device on as that can cause a serious short circuit. Next, send the device in for our liquid damage service as soon as possible. The sooner we receive a liquid damaged device, the higher the chance we can repair it.

It is possible that a device can begin working normally on its own after liquid damage, but it is very uncommon. It is more likely that corrosion and residue deposits will begin to form on the logic board making the repair process more difficult. We recommend sending the device in as soon as possible, even if it is still wet. The sooner we receive a liquid damaged device, the higher the chance we can repairing it.

Probably. Even if only one function is not working, it could be caused by a variety of things. When a device has been liquid damaged, standard rules do not apply. This why we offer a liquid damage service specially tailored for liquid damaged devices.

If we are unable to repair your liquid damaged device for any reason, your payments will be refunded, minus the cost of return shipping if applicable, and your device will be returned. If your device could not be repaired and you do not want the device back or do not wish to pay for return shipping, please let us know and we will recycle the device at our repair facility.

Maybe the apartment above yours has sprung a water leak. Or perhaps your teen tripped in the living room, spilling soda all over the TV. Either way, now your TV is wet, and it’s not working like it used to. Learn what to do if your TV got wet and how to know when it’s time to shop for a new one.

A small spill or minimal condensation on your TV may not cause irreparable damage as long as the water doesn’t reach the primary power sources. But even just a small amount of water on the circuit board can lead to permanent TV damage and short-circuiting.

Start by unplugging the TV. Then, wipe up the water with a non-abrasive cloth to avoid scratching your screen. Give your TV plenty of time to dry, and ensure that every drop of water has been wiped up so that it doesn’t soak into your television.

If your TV has sustained heavy water damage, it’s likely beyond repair, and you may need to replace or upgrade your television. However, any attempted repairs should be done by a professional.

If you have a water-damaged TV screen, you’ll likely know pretty quickly once you’ve turned it on. A water-damaged LCD screen is usually not repairable, as water can settle between the layers of the liquid crystal display and can be very difficult to dry. In this situation, consider replacing your water-damaged TV with a new one.

Your TV’s remote control may be a little more forgiving of water damage than your television. If you’ve spilled water on your remote, quickly remove the battery cover and batteries. Then, use a soft, non-abrasive cloth to wipe all the water off the remote. If the water spill was minimal and doesn’t appear to have gotten inside, wiping it and setting it out to dry should be enough.

If there was a big spill or the remote was submerged in water, it likely has internal water damage, making it less likely to continue working. Remove the battery cover and batteries, wipe the remote down, and place the remote in a zip-top bag filled with dry rice. Let the remote sit for 1-2 days before removing.

Replacing a water-damaged TV remote may not be as big of a deal with tons of universal and replacement remotes available. But a water-damaged TV is a different story!

Whether it fell out of your pocket while standing on a dock or got left out in the rain, it’s obvious that cell phones and water don’t mix. And while some new phones are marketed as being “water-resistant”, it is still a smart idea to keep your phone away from water whenever possible. There are a number of different issues that can arise if your phone has been subjected to water damage, from blurry photos and muffled audio to being unable to charge to not functioning altogether. While you might think that the only solution to these issues is to get an entirely new phone, there is a chance that your phone can be repaired.

If your cell phone has taken a swim or you suspect it has come into contact with water at some point, there are a few different things you can do to determine whether it has sustained any water damage. Many phone manufacturers keep water damage in mind when they design their phones and often place a liquid contact/damage indicator strip located inside the SIM card tray. This provides an easy way to check for water damage but often means that if the strip indicates that it’s been in contact with water, you will be ineligible for a manufacturer warranty.

While some encounters with water may leave your phone completely fried, sometimes all that is required is a single part repair, such as a battery, screen or speaker. Because each device reacts differently to water damage, we offer free estimates, so you can find out exactly what the cost of repairing your phone would be before any repairs begin. It’s important to bring your phone in for repair as soon as possible to avoid the water causing any major damage.

When it comes to drying out a water-logged phone, patience is key. The first thing you’ll want to do is remove it from the liquid immediately. Next, you’re going to want to turn it off and leave it off. This is going to help prevent any liquid inside the phone from interacting with any running electronic components. It’s important that you don’t continue to use your phone after it’s sustained any water damage. After turning your phone off, you’re going to want to pull off the case and if possible, remove the battery, SIM card and microSD card.

You might have heard that burying your phone in rice can help absorb some of the water, but this method isn’t very effective. Instead, silica gel from packets you often receive with new items such as shoes is much more effective. Leave your phone in the silica gel for 24-48 hours or until it’s fully dry before you try to turn it on.

If the picture responds to input but displays a messy image, such as jumbled multicolored squares, the AV (audio visual) board may be damaged. This is usually a rectangular circuit board located near the audio and visual cables. Replace obviously damaged parts using a soldering iron, or order a replacement board and carefully install it to the same screws and ribbon cables.

Check input cables for damage, or try other cables of the same type. If necessary, inspect the circuit board they are attached to and re-solder damaged connections.

The warehouse will check the device condition when we receive it. If it’s damaged, you may receive a reduced trade-in value or be required to pay a fee on your bill statement. (Prepaid customers will have the defective device shipped back instead.)

When inspecting a screen, remove any screen protectors and cases first. Tilt the device under good lighting conditions and inspect it at multiple angles. Screen damage includes hairline cracks that are difficult to see.

Mobile devices have a Liquid Damage Indicator (LDI) to show if the device has contacted any liquids. The indicator is white when it"s new, and it turns pink or red when it contacts water.

Wearables like Apple & Samsung watches often don"t have visible LDIs. Check for moisture under the display screen, as well as corrosion, discoloration, and fuzzy growth on the charging connection.

If the device does not fully turn on and load the home screen or if it cannot stay on without being connected to a charger, it"s considered not able to turn on.

No matter how careful you are, accidents happen. Screen damage and liquid damage are not covered under the warranty, so T-Mobile can"t exchange devices with this damage. But, we don’t want you to be stuck with a broken phone, so you have two options to replace or repair your damaged device:

You"re working on your computer one day when, suddenly, the screen goes black. You panic for a moment before realizing that it"s just your LCD screen that"s broken - not the whole computer. Phew! But now you"re left with a broken LCD screen and don"t know how to fix it. A damaged LCD screen can be a big problem.

There are a few easy steps you can follow to fix a broken LCD screen. First, identify the source of the damage. You will need to replace the entire screen if the LCD screen is cracked, shattered, or otherwise broken. However, if the damage is limited to a few dead pixels, you may be able to repair the screen without replacing it. Once you have identified the source of the damage, you can begin to take steps to fix it.

You can try a few things to fix a broken LCD screen. One of the first things you should do is check for any physical damage. If you see any cracks or other damage, you"ll need to replace the LCD panel.

If there"s no physical damage, you should next check your computer"s display settings. Sometimes, a broken LCD screen can be caused by incorrect display settings. Try changing the resolution or refresh rate and see if that fixes the problem.

If your computer"s display settings are fine, there"s a good chance the LCD panel is faulty. In this case, you"ll need to replace the LCD panel. You can buy a new LCD panel from a computer store or online.

Replacing an LCD panel is not difficult, but it"s important to follow the instructions carefully. If you"re not comfortable replacing the LCD panel yourself, you can take your computer to a repair shop and have them do it for you. Once you"ve replaced the LCD panel, your computer should be working properly again.

One of the most common causes of a broken LCD screen is physical damage. This can occur if the screen is dropped or hit by a hard object. Physical damage can also occur if the phone is bent, putting pressure on the screen and causing it to crack.

Another common cause of a broken LCD screen is a manufacturing defect. Sometimes, the glass that makes up the LCD screen may be too thin or not properly tempered, making it more susceptible to breaking. Additionally, the adhesive used to attach the LCD screen to the phone may not be strong enough, which can also cause the screen to break.

Temperature changes can also cause an LCD screen to break. If the phone"s temperature gets too cold, the glass may become brittle and more likely to break. Conversely, if the phone"s temperature gets too hot, this can cause the adhesive to loosen and the LCD screen to come detached from the phone.

Another factor that can cause an LCD screen to break is pressure changes. A sudden change in pressure, such as when a plane takes off or lands, can put stress on the LCD screen and cause it to crack. Additionally, if the phone is subjected to high-pressure levels, such as when it is squeezed in a tight pocket, this can also cause the LCD screen to break.

Finally, water damage is another common cause of a broken LCD screen. If water gets inside the phone, it can corrode the circuitry and damage the LCD screen. Additionally, water between the LCD screen and the touch sensor can cause bubbles to form under the screen.

Most people think that they cannot fix their own LCD screens, but they actually can. In fact, many people who have fixed their own LCD screens have gone on to become professional techs.

There are several ways to fix a broken LCD screen. One way is to use a screwdriver and some screws. Another way is to use a soldering iron and solder. Yet another way is to use a hammer and nails.

The soldering iron is a tool that is used to melt solder onto wires and then reattach them together. It works well for repairing broken screens on computers, TVs, and phones. You"ll need to use a soldering iron that is rated at least 600 watts and preferably 1,000 watts. A good soldering iron should have a temperature range between 200 degrees Fahrenheit and 400 degrees Fahrenheit. If you don"t know how to work with a soldering iron, you can watch some YouTube videos to learn.

Electrical tape is useful for covering up loose wires and making sure that they stay put where you want them. Screwdrivers are helpful for loosening screws and removing damaged parts. Make sure you get screwdrivers that fit the size of the screws you"re using. Socket wrenches are helpful for tightening nuts and bolts. You may not always find socket wrenches lying around, so make sure you bring along a set of these tools if you plan on doing any DIY projects.

If you aren"t comfortable taking your LCD screen apart, there"s no need to worry. There are plenty of places that offer LCD screen repair services. Just be sure to find a reputable place that has experience with the type of device you have.

You may also want to consider buying a new LCD screen. While this will obviously be more expensive than getting the screen repaired, it will save you the hassle of dealing with the repair process yourself. Plus, you"ll have a brand-new screen that should work just fine.

A screen protector is one of the best ways to prevent damage to your LCD screen. A screen protector is a thin piece of plastic that covers your screen and helps to protect it from scratches, fingerprints, and other types of damage. There are many different screen protectors available on the market, so be sure to choose one specifically designed for LCD screens.

Another way to prevent damage to your LCD screen is to avoid using sharp objects. This includes things like pens, pencils, and keys. If you must use a sharp object on your screen, be sure to use a soft cloth or another protective layer between the object and the screen.

It"s also important to clean your LCD screen regularly to prevent damage. Dust, dirt, and other debris can build up on your screen and cause scratches or other types of damage. Use a soft, dry cloth to wipe down your screen on a regular basis gently. Avoid using harsh chemicals or abrasive cleaners as these can damage the surface of your screen.

When you"re not using your LCD screen, be sure to handle it carefully to prevent damage. Avoid dropping or banging your screen, as this can cause cracks or other types of damage. Also, be careful when transporting your screen, as rough handling can damage it.

LCD screens are delicate and can be easily damaged. If your LCD screen is damaged, you can consider a few different options to fix it. You can try to repair the screen yourself, take it to a professional for repair, or buy a new LCD screen. Be sure to take care of your LCD screen properly to prevent future damage.

Please contact us for computer monitor repair services if you have any questions about LCD screen repair or replacement. We would be happy to assist you.

I’m trying to replace the optical layers of my old Dell Inspiron 5100 from an old lcd screen. The question is. in which order should the optical layers be positioned??

When I was fixing my screen I just removed all layers from the old screen and transferred them in the same order into the new screen. I didn’t pay attention how the layers were positioned.

I have a Tecra S3 which is only a year old, just out of warranty. The display just started to have problems mainly with the color red. Little red dots appeared everywhere and the color red had blotches of crappiness in it. Toshiba told me my warranty was over, I figured I’d try to fix it myself. I determined the problem comes from a weak plug in the display

I have a Toshiba M100 which is otherwise in great shape but has a problem with the LCD. If you look directly at the screen you can see dark grey spots scattered around the screen. To me this looks like mould or some sort of dirt and it’s definitely on the inside of the screen. So basically, the LCD is dirty on the inside!

To make the story worse, a friend of mine also bought the same laptop from the same source (private seller, used laptop, no warranty) and it also has the same spots. When I was buying the laptop I figured the screen was just plain dirty and I could wipe it off. But it turns out it’s not and the spots are driving me nuts.

Do you know whether or not it would be possible to open the screen and clean the LCD panel? I figure it’s the top glass layer but then again, I could be wrong.

I have a Sony Vaio FRV25. I was having fan problems, opened up the laptop, replaced fan. The screen is now black. I tried an external monitor and nothing happens.

Question: Can one replace only the flexible shiny front plastic cover which protects the Toshiba LCD screen? Mine has a little scratch where the cover bravely protected the LCD from a falling tool. It’s not the end of the world, but if I can replace this easily and economically I’d like to do it. If I could I’d replace it with a protective cover that was not so reflective.

Any ideas ?? i read in one of your posts that you fixed a laptop which wouldnt start because of a lose cable .. do you think this is a similar problem ? or is the motheboard DEAD ?

I have a 15.4” WXGA High-Definition BrightView Widescreen laptop that has a bright white spot that is very notable, what causes this problem? And is it fixable?

Just to say a big ‘thankyou’! Your site gave me the confidence to open my screen cover and swap the broken LCD with a working one…which saved a fortune. Keep up the good work and thanks again.

i read in one of your posts that you fixed a laptop which wouldn’t start because of a lose cable .. do you think this is a similar problem ? or is the motherboard DEAD ?

my daughter accidently knocked my e1505 off my desk now i have a three inch portion of my screen that is white with pink,green and yellow lines running through it,any suggestions

I replaced a cracked screen on an HP Pavilion dv8000. I followed your instructions, but I only get horizontal lines on my new screen. Any ideas what I might have done wrong?

i have a toshiba satellite p105 17”. i tried a massage method to remove a stuck pixel but instead of that when the laptop is turned off there is a circle on the screen which is like a blur bubble. when the notebook is turned on the circle is visible only on black background.i havent put much pressure so to cause damage.

I think I have the same problem as Savvas, tried to do something with probably bad pixels on my Toshiba Satellie A105 which I thought was a dirt at first. I did not do it to hard, but may be it suck water inside and now it has a large blur on the screen, when it is on it is not visible, mostly not even turned on black screen. what bothers me more, is the fact that I have two shiny spots on the screen, pretty visible and it is not dirt (as I have found out), they were there before. Can these be fixed? Can I try to repair at least the shiny spots within manufacturers warranty?

I’ve been striping and repairing laptops since 97′ in Toronto, Canada. I know that it has been pointed out with a big disclaimer, but I think for the average user or “tinkerer’ it would be LCD Suicide to disassemble the LCD layers on a spotty screen !!.

I’m very curious to know what kind of environment you did this in. I.E. Was it a clean room /box or were you just sitting at your desk ? I’m also going to hazard a guess that although you and I may have LCDs lying around in many “stages of broken” very few other people do !!

I’m not saying this guide is for everybody :). If you are not careful enough and have no experience fixing laptops, you can damage the LCD. That was my first time when I took the laptop screen apart. I had to reassemble it three times until I was satisfied. It was really hard to get rid of dust between layers.

I have a dell Latitude D600 and am having a problem with the lcd. When there are large black areas on the screen it kind of blinks black and red in that area. Also, there are very fine vertical lines throughout the whole screen. Dark blues have the blinking redish problem also. Also there is a slight double image of some elements on the screen such as the submit comment button below, I see a pink outline to the right of it. It does look normal sometimes, but a majority of the time it has these problems. Any suggestions? Thanks

Test the laptop with an external screen and see how the external video is displayed. If you have the same bad video on the external screen, there is a problem with the video card.

If you can see the whole desktop, including all icons and taskbar (the image on the screen appears to be compressed vertically), it’s possible it’s just a software related issue. Play with the screen resolution, test if the display works fine in Safe Mode. Try reinstalling the video driver.

Thank you very much for detailing your disassembly with photos. I’ve recently gotten a fully functioning Inspiron 5100 with good external display but the LCD is completely dark. I am considering replacing the backlight or inverter myself and you’ve helped a lot with your pictures. I have the display panel removed but cannot tell one part from another. For instance I wondered if the backlight was behind the top edge or the bottom edge and was the inverter the circuit board in the middle of my display of the one that has the caution tape on it running across the top of the panel.

Is it a thin vertical line about 1-2 pixels wide running across the entire screen? If yes, then there is not much you can do to fix it. It’s a screen problem and you’ll have to replace the screen (or get used to this line).

Post-op I’m convinced the backlight is fine and therefore the inverter is at fault. For roughly $30 I hope to aquire a replacement. This will be a reasonable cost for the fix.

I see that, on your pictures (and in my own laptop) there is that white tape with specific instructions not to touch it. However, it would appear that you are, in fact, touching it when you’re displaying where to remove the screws on the side of the screen.

I believe they put “Do not touch” instructions because there are data cables connecting the circuit board with the LCD and they are located right under the white tape. I think nothing terrible is going to happen if you accidentally touch the tape, but do not push on it because you can damage the data cables.

Secondly, I formatted the C:\ drive and now am trying to install XP…but it keeps turning the screen off after 3-4 minutes…and I have to restart the computer so that the screen comes back again…is there a cure to this? ANY help is appreciated.

If the laptop starts with normal video but after some time the backlight goes off (you still can see an image on the screen) then most likely it’s just a faulty screen inverter. If the screen goes off and there is no backlight or image, then it’s not an inverter issue.

hi, ive justknackered my sceen with water damage, its stillworkingbut a can see a water mark esspecially on awhite background.i don’t fancy taking the screen apart because i have important work on my comp anddon’t wannabreak it. it seems to have subsided, (only damaged it a coupl of hours ago!) what are the chances of it evapourating and evrything bing hunky dory again?

Probably a better chance of that than of you improving your spelling skills. If it was distilled water (pure H2O), you might have a chance of it coming clean. The impurities are what makes a mark and tap water (or bottled) has a bunch of them like trace minerals, microscopic solids, etc. If it was still wet, you might be able to remove the bezel, detached the screws/clips that hold the screen in place, and “drain” it out by taking the screen, holding it vertically, and gently tapping it against a hard surface to possibly spread out or move the water out of the screen. Kind of a long shot, but there’s not much you can do when you don’t want to go to the source of the damage. There’s an active market on ebay for used screens.

Followed the article on LCD screen repair. Found it excellent. Cleaned the glass layer with Walmart glasses cleaner (70% isopropyl alcohol might also work) and used latex gloves without talc to avoid fingerprints, have not taken a screen appart before but dissassembled an old broken one to get the back sheets and learn the pitfalls . The silver back layer does not seem to clean and needs to be replaced if the water damage is on this layer..

i dropped my work laptop in puddle on friday and its wasnt drying out – so followed ur and hp manual instructions to take screen apart dried various bits of lcd screen 90% sure they all back correctly as they only fit in one way and now have vertical lines across screen n no picture hooked it up to external monior and it worked ok. ple\se tell me i haven’t messed it up! and theres something i can try to put it right so that i odnt have to crawl back in to work n get b******ed

Thanks very helpfull, I also tryied to fix my LCD screen for the first time. I got a replacment on ebay for a LCD 15″ dell insiron Model 5100 but the cable connections are diffrent from LCD to mother board as my old one . Any idea where I can get a cable?

I need a screen for my Dell Latitude C640. I dropped it and the screen broke. Do you know where I can find one real cheap. The computer works fine. I live in Richmond, Va. Right now it is hooked up to a regular monitor.

Probably the cheapest one you’ll find here. I just searched for “Latitude C640 screen” and found two LCDs, one for $85 and another one for $65. I think this cheap enough.

Hi! I have successfully transferred LCD screen from Inspiron 6000 to Inspiron 6400 but I had to take along inverter and video cable. I really like this particular screen and I wonder if it likely to be compatible with other brand laptops? I plan to upgrade to a santa rosa laptop and don’t want to limit my choices to Inspiron 1520. Thanks!

I ony Vaio FRV37 with possible moisture damage around the outer edge. I never had to clean the screen so I’m not sure if it is moisture. The damage- some spots with dark uneven middles that fade out then go dark at the outer edges – some are at least 1/2 inch in diameter. The extensive damage from right side across the top to left side and are darker at inside edge and lighter closer to bezel. All spots are very noticable on white background. I cannot find any examples of screen damage to compare. I need to know is this indeed water spots or LCD damage so I can fix it or replace it. I do have another undamage screen as replace but only as a last resort. Thanks for writing such an informative article.

My dughters Inspiron 6000 has the black screen problem with (very) faint image. How can I tell if it’s the backlight or inverter which is bad and can the backlight be changed on this model without the horror story above ? Thanks for any help you can give, a local repair shop is quoting £180 for a fix !

Another problem I have is that one of the sreens just does not work, that is to say the backlight is fine, but no image. I am sure that the inverter and the cable to the screen is OK, as they work properly with another screen.

Take a look at the example 2. Does it look like your screen. If it does, most likely you have a faulty screen. You’ll have to replace the screen in this case.

I dropped my laptop about couple of months ago. the top corner of frame is cracked. i turned on computer a thin line bluish/white vertical from two inches from the edge. it ran ok. its starting to get larger due to opening and closing the laptop. it is a hp new model. when i hold the screen tight the line does get thiner. please help

If the LCD screen lights up and you can see an image on it, even though the image is completely garbled or distorted, the problem is not related to the screen inverter. When the inverter goes bad the LCD will not light up at all.

You’ll have to test your laptop with an external monitor connected to the laptop VGA port. Set the laptop to output video on the external screen. If both internal and external screens display the same bad image, most likely you have a problem with the video card. If this defect appears only on the laptop LCD but no on the external screen (external screen works fine), then most likely your laptop has a defective screen.

I have an HP zd7249. My screen is not functioning properly. When the computer is on, the screen is dark, but I can see that a light, which I assume is the backlight, is actually lit. From what I have read here, that would indicate that the CCFL and the inverter would be fine. I should also note that I have connected the laptop to an external monitor, and I get a perfect image. What do you think my problem is?

I’m using a Dell XPS M140. About 8 months ago I replaced the LCD screen. Currently when the laptop is running off the battery the screen will stay lit for about two mintues and then go dark. You can still see the image in the background. When running off the AC cord the LCD will remain lit. I was wondering if this is something that I did incorrectly upon install or if I have an off setting somewhere. Thanks.

I was running from my car to front door wile it was storming and some rain drops somehow got in the lcd screen. I have a Compaq Presario V300 made by HP and it is basically new and is a great system. As soon as I got inside and noticed the damage, I looked up on google “I got water in my laptop screen”. This was the first site and it worked great!!!! I read through and followed all directions (my lcd is connected to the laptop a little different though). It worked perfectly and I was able to get all the rain water out before it was able to dry and stain. I recommend this to anyone with the same problem. Just like the directions say, be very careful though! THANK-YOU THANK-YOU THANK-YOU ! ! ! ! ! ! ! !

When the computer is on, the screen is dark, but I can see that a light, which I assume is the backlight, is actually lit…I should also note that I have connected the laptop to an external monitor, and I get a perfect image.

Could be a connection issue between the motherboard and the screen. First, I would try reseating the video cable connector on the motherboard, it’s easier to access this one. Second, I would check the connection between the video cable and the LCD screen. To access this one, you’ll have to open up the display assembly and take a look on the back side of the screen. Make sure the video cable is plugged in correctly, all the way inside the socket.

a few weeks ago a family member left my laptop in a postion where no air could come out of the ventilators. when i discovered this my laptop was really hot. Now my laptop will begin to heat up and won’t cool down unless i shut it off. Also, my computer screen doesn’t look right. It’s hard to see, especially on darker backgrounds. how can i fix this?

My DV1000 screen went dark (with faint images of the screen) 2 weeks ago – I ordered a new inverter (from invertercentral.com) that was supposedly compatible with my DV. Replaced the inverter and found out that the old one didn’t have the exact same number as the new one.

Now my laptop will begin to heat up and won’t cool down unless i shut it off. Also, my computer screen doesn’t look right. It’s hard to see, especially on darker backgrounds.

I have question about removing all the films fron an Inspiron 6000 LCD screen and replacing them. First, is there anywhere I can get new film sheets? Second, when I put everything back together, is there a schematic on the placement of the film sheets and/or does anyone know what order they are supposed to be in? This is a used laptop that I aquired and someone has already taken the LCD completely apart. All the parts are there and there are no visible scratches or anything like that but I notice that the clear plexiglass panel is thicker on one edge than the other. I am going to assume that that is because it sits on the backlight but I really want to know before I start in on this. I have the film sheets (Background?) laid out like they came to me but if I could find a schematic showing which one goes in first, second, etc. I would be in heaven.

It’s possible that the video cable got pulled from the connector on the back of the LCD screen and is not making a good connection with the screen. Reseating this connection might help, I would try it first.

Yes, I believe these transparent layers has to be placed in the order they were removed. If someone has already taken the LCD screen completely apart and didn’t assemble it back the way it should be, probably your are screwed. I think you’ll have to find a new screen.

Hi, I have a problem with my laptop, recently I turned on my laptop and the screen stays plain white, I could hear the sound of windows started, but it stays white, if I remove the power cable, the screen will start dimming, on the other hand, I tried to test the LCD screen on my brothers Identical laptop and it WORKED wonderfully, when tried to put it back to mine, it’s WHITE! this is frustraiting! anybody please help me..

Your LCD screen works fine with another laptop, so there is nothing wrong with the screen. Apparently, you have a problem either with the video cable or the motherboard/video card.

The lid catch on my Compaq Evo N600C is broken; I have obtained a damaged N600C screen with a good catch system. However, I cannot discover how to separate the screen form the bezel so I can remove the catch system. I have removed all screws I can see, but the top left and left side will still not separate.

Sometimes HP glues the LCD bezel to the screen with double-sided sticky tape. In cases like this I usually insert a piece of plastic (guitar pick, credit card, library card, etc…) between the bezel and the screen and move it alone the side to separate both parts. Be careful with the screen.

I took it apart and found the problem. On the left side of the LCD (screen facing you, back behind you), it has some flexible circuits that connect with the white tape. When one part doesn’t touch the white tape, the image is dark (or has vertical lines). Applying pressure connects the circuit to the tape.

This flexible circuit has a lot of very small connectors. I’m afraid you cannot fix it at home. Maybe you can put a piece of eraser between the screen and the screen top cover, so it always apply pressure on the screen? It’s just a wild suggestion but it might work.

I have a Dell Inspiron 6000 with a wsxga+ lcd that is cracked and displays weird colors when turned on. I have tried it with an external monitor so I know the video card still works. Here’s the question: my buddy has a screen from a Dell Inspiron 1520 with the same resolution and he is willing to let me have it cheap. How can I find out if it is compatible? I don’t want to bother him and have him ship cross-country if it won’t work. I have conflicting answers from others who say it will work no problem and also that it won’t work because of the inverter. I’ve searched everywhere I could think of to no avail. Since you sound extremely knowledgeable, What do you think? Any help would be greatly appreciated. Thanks.

I doused my Inspiron 6000 with water and had water between the laminaire of the LCD. I tried all the stuff recommended by others, but in the end I did the exact same thing you did, except I cut the sealing tape and applied new when done. Mine is now as good as new.

A couple of tips. You need the right tools, and patience. Dont try to get along without a good quality 0 and 00 phillips, aluminum foil tape and mylar tape. To clean the various layers I used eyeglass cleaner wipes, and changed them often. The alcohol in them kills any organisms, and they are lint free. The LCD itself is relatively simple, and more durable than everyone seems to let on. Take your time and roll the layers over as you clean them so you dont mess up the order. An ice tray will allow you to sort the screws. Make sure the LCD is properly supported all the way across its surface on a book and soft cloth, and dont do this when tired or upset. By the way I cleaned the LCD panel too, and it caused no damage whatsoever. Good luck to all. JimA

I have a toshiba portege a100 12.1 inch laptop with a cracked lcd. Is it possible to use the lcd from an m100 12.1 inch and transplant it into the a100?

I had a sploshy screen on the bottom right corner of my Laptop, due to spilling fluids on the laptop, it showed up as super bright patches on the LCD.

Both the cable connectors are the same. 20 pins. However, I have not purchased the screen from the m100 as I do not know if it will fit. The A100 has 2 circuit boards attached to the screen and the M100 screen only has 1. I am asking so as to know if if should purchase the M100 screen online from auction.

Hi i have a dell D600 latitude and the front cover is very badly scratched when you removed the lcd could you have easily removed the front lid cover as i want to change mine to a nice new lid/cover but i dont know how to go about it is it easy to change the fron cover can you advise on how i could do this please many thanks

I don’t know if the screen from M100 will work on A100. I’ve tried to research online but it looks like both screens have different part numbers and they might require different video cables. If I would be you, I would search for the original A100 screen replacement. Find the part number on the back of the LCD screen and search by the part number. It will help you to avoid unnecessary waist of money.

I have a cracked screen on my dell d410. I was able to replace the lcd, but when i booted up, the screen showed white. Is there something wrong with the inverter or video cable?

Test the laptop with the cracked screen again and see if you can get image. If you get it with the old (cracked) screen but not with the new one, probably your new LCD is bad and you’ll have to replace it.

Thank you so much for your detailed instructions on taking about the lcd..Dell didn’t send any instruction with the replacement and this was my first time attempting this…I was able to follow the instructions without wrecking anything….and now my user is happy happy happy!!!! Thanks again~!

Disregard the blurry picture. That’s my lack of photography skills. Instead, please tell me what’s making any LCD I connect to this laptop display images (including BIOS screen) 4 times. Despite the bad photography, the 4 images are perfect representations of the 1 image that is supposed to be seen on the display, i.e. no blurriness or dimness. External monitors show the 1 image perfectly.

this might be the wrong place, but you guys seem to know about this stuff, but … is it possible to rip the lcd off a dead laptop and with some messing about, get it to act as a standalone lcd vga monitor ?

I want to use my D600 screen on my Dell 610 (D610 screen has 3 cracks over it, that’s why I want to change screens). Every thing looks the same when I take it apart, except one thing. The cable from my D600 has more wires connected to the screen. The socket itself looks the same, so I can move the cable from D600 to D610 or vice versa. But when I boot the D610 with the D600 screen, I have tiny colourful strips all across the screen. It doesn’t matter witch cable I use, same result. The screen cables has a tag, the D600 has CSSWJ.Wanshih REV.3A 04/03/15 DD0JM1LC0000 and the D610 CSFFOL.Foxconn REV.3A 06/01/03 DDJM5BLC107. Can I do anything to make this work?

i spilled a small amount of diet coke on it towards the left side of the keypad. now when i try to turn it on all the lights come on for about 5-8 seconds then they turn off and no activity on the screen.

Can anyone tell me how to fix this or what to look for when i take it apart?Look for corrosion on the motherboard. Apparently the motherboard has been damaged by coke.

When the laptop is switched on the LCD shows a dark gray light (for less than a second) and then turns black. Earlier it used to flicker and come back but one day it just went black and is same since then.

Now, assuming that I am correct in the above assumption, it could be the video cable or the LCD screen/circuit itself. I have removed and replugged the video cable but nothing happens. Is there a way I can guarantee a faulty video cable without trying another one? (i suspect the answer to be no)

Now the final question, I am willing to buy a new LCD screen for my notebook and its available on ebay (and a few other sites). But is it possible that its not the fault of the screen at all? Could it be the circuit on the motherboard between the video card and the LCD connector on the motherboard that is breaking the signal? I ask because if this is the case then even buying a new screen wouldn’t help.

I have tried my screen on another laptop (Inspiron e1405) which has a different video cable connector to the motherboard. But I managed to attach my LCD (of Inspiron 2200) to e1405 using its video cable and the LCD works fine (I used my inveter only).

I recently revived a friends laptop that had been his daughters. The display is splotchy. He is not interested in spending $100 for a replacement LCD panel. It displays text OK. Thats enough for him. The colors are muddled. I do not think it is bad pixels, as during the Dell diagnostics routine, it displays solid colors perfectly. It does not display red well when mixed with other colors. The colors are perfect when displayed on an external CRT monitor.

Just a quick ?. I do not want to throw good money after bad. I bought ny daughter a Dell Inspiron 2200 about 3 years ago. She used it about 20 hours watching dvds. About 2 weeks after the 1 year warranty, the screen went dark. If you have light shining on it at the right angle, you can see and read what is on the screen. Obviously, it works fine with a monitor.

Your instructions on how to replace the layers was quite informative. However, could you please advise if this solution is applicable to a lcd with different colored vertical lines on the screen at startup and windows?

Thank you for so detailed instructions . I have read trough all posts but don’t find neccessary answer. How do You think- changing LCD layers will help to remove white spots? Now I san “see” through monitor and see all support points behind LCD as white cloudy spots. I have Dell Latitude D600. Thank You

The whole process took a total of 30-minutes to effect repairs on a severely crack LCD Panel on a Gateway MX6124. I Can not Thank These People Enough For Helping Explain What I thought was an ardious task being made simply for a layperson.

While creating this guide, I had to disassemble/assemble the screen a few times. It wasn’t as easy as it looks in the instructions above.