3.5 tft lcd arduino mega in stock

This TFT 3.5 Inch LCD display support 480x320 pixel resolutions. The display uses the ILI9481 graphics controller. The module includes the 5V-3.3V power conversion circuit and no additional level conversion circuitry is required. This Module can be inserted directly into the Arduino Mega2560 Board.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (3.5" diagonal) bright (6 white-LED backlight) and colorful (18-bit 262,000 different shades)! 320x480 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6236 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.

The pin32 (SDO) of 3.5 display module is also used by touch panel or SD card SPI interface, so we must cut off this pin to avoid conflict with the touch panel or SD card.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560).

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

This is a 3.5-inch 320 * 480 resolution TFT color screen. It supports working boards such as Arduino uno and Arduino mega2560 and Arduino due. Also supports STM32, 51 and other conventional microcontrollers.

When using this screen, you do not need any wiring operations, just plug onto your arduino board, we will provide the corresponding Arduino library files, the development code is open source, you can use arduino and this screen to build some applications.The backlight always on, can not control the backlight, backlight is connect to 3.3V.

This 3.5 inch TFT LCD Display is the larger version of the 2.4″ display designed specifically for Arduino Mega. This Arduino shield contains a 16 bit color TFT screen with a large 3.5″ display and is designed to fit directly into the standard headers of an Arduino Mega requiring no additional interface hardware. It support a relatively high resolution of 480 x 320 pixels.

i read that the screen consumes a lot of power and i observed that arduino is more hot than it should, so i dont know if there is something i can do about it or it will damage it long term. i guess the best solution is to bypass the power pin and use external power supply with enough current available.

Now, I have bought 3.5" TFT LCD display for my Arduino Mega 2560 R3 to try whether I could run the screen or not, and it is not working now! I am so depressed and angry for these two"s misbehaviors. I have already checked website and a lot of Arduino IDE code examples and libraries such as UTFT.h, UTouch.h, UTFT_MEGA, UTFT_CTE, TFTLCD. I tried these and I can not run my 3.5" screen. Where am I faulty? There is something below the screen shield: www.mcufriend.com and 3.5" TFTLCD for Arduino 2560. Are there any basic code or have anyone tried to run Mcufriend"s displays correctly?

This 3.5-inch TFT LCD shield plugs directly onto an Arduino Uno and Mega 2560. It also comes with an SD card holder that is usually used to store the images you want to display.

It3.5 Inch TFTfeaturedArduino LCD Display Module,Compatible with Arduino Mega 2560. Direct connection can be made on Arduino.Arduino Mega Lcd Displaycan be used asNOTE:This screen has no touch feature.Form Color: Black

This display can be mounted on an Arduino Mega or Due. It has a fairly high resolution of 320*480 pixels and is also quite large with 3.5 inch LCD size.

This 3.5 inch TFT LCD is based on the ILI9481 LCD driver and gives a very sharp/nice picture quality and works amazing well with Arduino Uno and Arduino Mega Microcontrollers. Unfortunately this display is not a touchscreen display, however it makes it up with the included MicroSD Card Slot. No soldering, no wiring, no fuss just plug and play!