sainsmart 3.2 tft lcd display pinout pricelist

SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

There is built-in SD card slot in the shield, so we can use it to upload images. But the images need to be converted RAW format first.You can use the tool here. SD libraries need to be preinstalled for displaying the image.

SainSmart 3.2" TFT LCD Displayis a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

Reason: The hooks on the backight of ER-TFT032-3.1 is always complained by most customers for inconvenient assembly. So we cancel the hooks in the new version of ER-TFT032-3.2.That"s the only difference for these two versions.

ER-TFT032-3.2 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller and optional 4-wire resistive touch panel and 3.2 inch capactive touch panel with controller FT6236,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8/16-bit parallel,3/4-wire serial interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

※ Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

ER-TFT032-2 is 240x320 dots 3.2 " color tft lcd module display with ILI9320 controller and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 16-bit parallel interface. .FPC is soldering type,there is no need for zif connector.Lanscape mode is also available.

SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

3.2"" TFT LCD module with 40 IO, it is more than a LCD module and colleagues also includes an SD card slot, whether with touch function. (Here we are with touch screen function module)

Great display, nice size and response. If you plan on using an Arduino, please get the shield also. It will save you a ton of time and studying( the 40 pin connector on the back must be broken out in groups and resistors put in that dump to ground. )..

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

If you are looking to get into Arduino development or are wanting to expand your existing collection, this is the perfect item for you. You get a great value for your money:SainSmart Mega 2560 board (Arduino clone) ($33)SainSmart TFTP display with touch screen and full sized SD card slot ($25)SainSmart TFTP Display adaptor ($15)Short USB cableI spent $46 for this setup, so the value is obvious.The Mega 2560 clone worked perfectly, the display worked perfectly and the adapter board mated them properly. I had purchased a Seeed 3.2" display at Radio Shack for $49. It had many issues and I returned it and used the money to buy this setup. This display is much faster than the Seeed display and the drivers were very easy to locate and install. Just google "UTFT drivers henningkarlsen" and get all of the UTFT drivers. Henning has several more drivers on his site, go ahead and get them all. They are very easy to use and configure. To use the drivers with this particular board (they are "universal drivers") use this setting for the board type:UTFT myGLCD(ITDB32S,38,39,40,41); // the ITB32s and correct pins for Mega shieldSo in summary:Pros:1. Great value for the money2. Everything worked greatCons:1. Not a "real" Arduino. You"ll have to decide for yourself how important this is to you.The nice thing about SainSmart is that they admit that they are cloning the Arduino boards. Most of the boards available on Amazon are counterfeits and the sellers are not particularly upfront about this. These counterfeit boards exactly copy the Arduino boards, definitely graying the area between legitimacy and piracy. SainSmart clearly marks their boards as clones. I appreciate this honesty in a company, especially when there"s more money to be made by tricking buyers into purchasing counterfeit boards.I highly recommend this package for anyone wanting to get into Arduino development or wanting a touchscreen. The value is great. Now, I guess I need to hunt down a 7" TFTP display to continue this adventure.[9/19/13] Update:After digging into the touch screen, I found that the UTouch lib had some serious accuracy problems, even after trying to use the calibration utility provided with the library. I re-wrote the lib and now I find that the accuracy of the screen is very good. To re-write the lib, you need to take these factors into account:1. The reading of the x values for the screen at the extreme left and right edges.2. The reading of the y values for the screen at the extreme top and bottom edges.This is confused a bit by the fact that the screen is natively in portrait mode. Which is to say that the long side is the y-axis and the short-side is the x-axis. I wanted a landscape mode, so I swapped the coordinates in my driver.Once you know the x and y extremes for the touch screen, simply use the map function to map them to the actual screen coordinates. This gives you a pretty accurate x and y for the display.The other issue I had was with how the touch screen was sampled. The library code polls the touch screen several times per read and averages the results to get a more accurate reading. In the case of "EXTREME" accuracy, it polls 10 times. The problem with this is that if you lift your stylus during the polling, the last few reads are bogus and throw the entire read off. You can see this happening in the SainSmart demo video that they posted for this device. The symptoms are that pixels get set on the sample paint program way far away from where the stylus is. Not cool! The fix is to only sample the screen if the screen is detecting the stylus as being pressed. You can do this by checking the dataAvailable() before each read in the poll. If there is no data available, don"t do the read.I wish I had a more effective method of sharing this information with the Arduino community.

In this guide we’re going to show you how you can use the 1.8 TFT display with the Arduino. You’ll learn how to wire the display, write text, draw shapes and display images on the screen.

The 1.8 TFT is a colorful display with 128 x 160 color pixels. The display can load images from an SD card – it has an SD card slot at the back. The following figure shows the screen front and back view.

This module uses SPI communication – see the wiring below . To control the display we’ll use the TFT library, which is already included with Arduino IDE 1.0.5 and later.

The TFT display communicates with the Arduino via SPI communication, so you need to include the SPI library on your code. We also use the TFT library to write and draw on the display.

In which “Hello, World!” is the text you want to display and the (x, y) coordinate is the location where you want to start display text on the screen.

The 1.8 TFT display can load images from the SD card. To read from the SD card you use the SD library, already included in the Arduino IDE software. Follow the next steps to display an image on the display:

Note: some people find issues with this display when trying to read from the SD card. We don’t know why that happens. In fact, we tested a couple of times and it worked well, and then, when we were about to record to show you the final result, the display didn’t recognized the SD card anymore – we’re not sure if it’s a problem with the SD card holder that doesn’t establish a proper connection with the SD card. However, we are sure these instructions work, because we’ve tested them.

In this guide we’ve shown you how to use the 1.8 TFT display with the Arduino: display text, draw shapes and display images. You can easily add a nice visual interface to your projects using this display.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touchscreen.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touchscreen.

This TFT screen is really big (3.2" diagonal), bright (6 white LEDs) and colorful! 240x320 pixels with individual RGB pixel control, which offers a much higher resolution than a 128x64 black and white display. As an added bonus, this screen is already equipped with a resistive touch screen, so you can detect finger pressure anywhere on the screen.

This display has an integrated controller with RAM buffer, so the microcontroller does virtually no work. The display can be used in two modes: 8 bit and SPI. For 8-bit mode, you will need 8 lines of digital data and 4 or 5 lines of digital control to read and write on the screen (12 lines in total). SPI mode requires only 5 pins in total (SPI input data, output data, clock, selection and d/c) but is slower than 8-bit mode. In addition, 4 pins are required for the touch screen (2 digital, 2 analog) or you can purchase and use our resistive touch screen controller (not included) to use I2C or SPI.

We have integrated this screen on an easy to use card, with SPI connections on one side and 8 bits on the other. Both are 3-5V compatible with high-speed level switches, so you can use them with any microcontroller. If you choose SPI mode, you can also use the built-in MicroSD card to display images. (microSD card not included, but any will work)

I haven"t used that particular LCD, but there appears to be a comprehensive library supporting it (and many other LCD driver chips) at: Electronics - Henning Karlsen

As regards pin-out the library lets you choose whatever pin out you like for the control lines, but if using parallel mode (8 or 16 bit) there are fixed pin assignments documented in the download. You could try asking seller for the pinout of module, or see if its marked on the actual device.

I have used other LCD modules from eBay and its usual to have to do a little detective work to hook it all up - worth checking on the internet if anyone else has working things out for you and documented it.

※ Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

ER-TFT032-2 is 240x320 dots 3.2 " color tft lcd module display with ILI9320 controller and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 16-bit parallel interface. .FPC is soldering type,there is no need for zif connector.Lanscape mode is also available.

This 3.2 inch lcd screen adopts ILI9341 driver chip, and it is with 2x20P male headers interface, namely total 40 pins, so it supports mega 2560 board, but not compatible with uno r3, nano and esp32 board.

This 3.2 inch display works at 3.3V. If you use it with mega 2560, please insert TFT 3.2 LCD expansion shield, not directly connect board with the 3.2 inch screen. Otherwise, it"ll be burned.

As an option, you can order this TFT pre-assembled onto a breakout/carrier board. The board allows easy prototyping through its 0.1" headers. You can also include the carrier board in your end product to simplify construction and assembly. The carrier board contains a constant-current switching LED driver. The PCB is sized to fit neatly within the outline of the display.

This kit consists of a CFAF240320A-032T TFT LCD module mounted on a carrier board. The carrier board supports a current driver for the LED backlight of the display. It is also available under Additional Options on the website page for CFAF240320A-032T.

SainSmart 3.2" TFT LCD Displayis a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

3.2 Inch TFT LCD with 262K color 480x 320 resolutions.The controller of this LCD module , it supports 16-wires DataBus interface.Moreover, this module includes the 5V-3.3V power conversion circuit and Level conversion circuit, This Module can Directly inserted into the Arduino Mega2560 Board ,it also includes the SD card socket and SPI FLASH circuit

Support Arduino Mega2560 Directly inserted
With Full-angle IPS TFT panel
OnBorad level conversion chip for 5V/3.3V MCU
Compatible with 3.3/5V operation voltage level
Compatible with Arduino-Series development Board.
(Please notice:This Screen is not touch screen)
Provided 12-examples with Arduino ,3-examples with STM32
With SD Card Socket
With SPI FLASH circuit

Arduino mega + 3.2" tft case. there are 2 different case bottoms, 1 without a hole and 1 with. both cases have a cutout for powering the Mega from a USB.

ER-TFTM032-3 is 240x320 pixels 3.2"tft lcd module display with ili9341 controller,adaptor board,optional touch panel,memory chip or card,font chip.Souce from EastRising/buydisplay.com

This is an update to the FreeTouchDeck case by Dustin Watts that holds a 3.2" TFT display since I bought a different size than Dustin used. I modified the Top_for_TFT_with_Headers.stl file. I"ve also uploaded the Fusion 360 file.... I use hot glue to...

Simplified model of a 3.5 inch LCD for Raspberry Pi. ...I used the usb connectors from this model: Raspberry Pi 3 Model B Reference Design Solidworks CAD Raspberry-Pi Raspberrypi Rpi

I needed an accurate model of the 2.8" TFT shield for the Arduino. ...It was a bit of a challenge as these are not manufactured to the tightest tolerances so I added some standard deviation to the model so that it should fit most use cases.- Pinheader...

Models from MSP2202 (2.2") and MSP3218 (3.2") TFT display modules (or similar), which might be handy for a placeholder in designs, for example enclosures. Please compare MSP2202 and MSP3218 datasheets with your displays to confirm that there are no...

adjustable angle mount for Sainsmart 12864 LCD case on 20x20 profile You can use the Display as a remote device.http://www.thingiverse.com/thing:327209 is perfect for using. Thanks. ...

After my first attempt to mount the 3.2" MKS TFT display instead of the Creality display in the original Creality CR10 electronics box (https://www.thingiverse.com/thing:3440802), I found the option "BABYSTEPS" could not be selected using the TFT...

Here you will find a simple frame for the 3.2 "TFT touch screen ILI9341. This frame is designed for gluing on a plastic box. Details of the display can be seen in the attached pictures. ... The display holds four M3x6 screws on the frame.

A small mountable holder for a fasttech LCD module. Mounting pins are a little tight but can be snapped off if not needed. Mount holes are designed for assorted leg or spacer designs. Holes are 5mm dia, 34mm apart and hole centre 5.5mm from edge if...

"lcd hinge" is for behind the lcd. "base hinge" fits into the duo case pins and takes the lcd hinge shaft My hinge snapped when I tried to jam the shaft into it, blue pvc pipe glue visible on assembled photos.. ...does the job.

Case for the ESP32 D1 mini and a TFT 3.2 inch (ILI9341). I designed this to connect a ham radio transceiver FT-817 or FT-818 to the display. The USB port of the ESP32 will later only be used for programming, while the cable on the back is connected...

ER-TFTM043A2-3 is 4.3" tft lcd module display with capacitive touch panel,serial and parallel interface,RA8875 controller,microsd card slot,font ic,flash chip.Souce from EastRising/buydisplay.com

ER-TFTM043-3 is 4.3" tft lcd module display with serial,spi,i2c and parallel interface,RA8875 controller,microsd card slot,font ic,flash chip.Souce from EastRising/buydisplay.com

ER-TFTM043-4 is 4.3" lcd touch screen module display tft with ssd1963 controller board, mcu 6800,8080 parallel interface,micro sd card slot,font,flash chip.Souce from EastRising/buydisplay.com

ER-TFTM043A2-7R is 4.3"800x480 tft lcd display with RA8875 controller board, optional touch panel,serial/parallel interface,micro sd card slot,font,flash chip.Souce from EastRising/buydisplay.com

ER-TFTM040-1 is 4"(3.97") tft lcd display with NT35510 controller,breadkout board,optional resisitive touch panel,memory chip or card,font chip.Souce from EastRising/buydisplay.com

ER-TFTM024-3 is 2.4"tft lcd touch shield qvga 320x240 dots,ili9341 controller,available for touch panel controller,sd card slot,font chip,flash,serial+parallel.Souce from EastRising/buydisplay.com