monoprice desk mount for 2 lcd displays factory

I purchased this mount to stack monitors for my Digital Color grading suite. After purchasing a 3rd monitor for critical color evaluation, I found there simply wasn"t enough lateral space to accommodate the new 27 inch monitor with my other 24 and 25 inch monitors; I had to go up to be able to use all three on my current desk.

I suggest you purchase a small tube of Loctite screw thread locker (or use some fingernail polish in a pinch), back out the main screws that hold the collars that hold the VESA mounts to the pole and lock these screws down TIGHT before attempting assembly or they might loosen up and allow the monitor to swivel horizontally after mounting the monitors.

Also, since the metal parts look as if they are powder coated, the screw holes on some mating surfaces might be a bit difficult to get started, so before you are trying to balance a monitor and start a screw into a mating hole, run these screws in and out of them to clear out any manufacturing over spray in the threaded holes. Makes life easier...

If you are doing this by yourself, as I did, I found the easiest way to mount the bottom monitor to the poles were to attache the VESA mounts to the monitor, stand the monitor on its side, resting on the desktop and then bolt the VESA mount to the collar. You only then have to pivot the monitor to horizontal and then tighten the collar around the stand pipe. The top monitor should be assembled to the VESA plate, attached to the collar, roughly leveled and then lowered over the pole to the correct height. It"s tricky but it can be done by one person.

Be prepared to spend some time adjusting and re-adjusting the height, tilt and level of each monitor to get them just right, as they lock in place and are not adjustable when fully tightened. Also, be aware that if one of your monitors has a connection you use that sticks out the back of the monitor at a 90 degree angle in line directly under the VESA mount, you will have trouble tilting the monitor down. My uppermost monitor had such a cable and it took some finessing to get it in place with the stiff video cable sticking out and hitting the support pole, but I was able to make it work.

My only concern now is that I might have a stiff neck from looking up at the top monitor for long periods, but considering my other options (basically none), I"ll have to learn how to deal with it...

Excellent question. Inside the bracket to the inside edge of the disc is only 1/2". Obviously in your case that will not clear. The disc itself is almost 1-7/8" in diameter as well.

You could put the mounting bracket "backwards" and use the holes to screw it in to the desk, rather than being clamped. I did not need to do this, but that obviously would not be as secure, depending on how well the screws bit in to the desk.

I purchased this mount to stack monitors for my Digital Color grading suite. After purchasing a 3rd monitor for critical color evaluation, I found there simply wasn"t enough lateral space to accommodate the new 27 inch monitor with my other 24 and 25 inch monitors; I had to go up to be able to use all three on my current desk. The stand was quickly shipped, well packed and arrived with all parts. Assembly was fairly straightforward, if not somewhat fiddily. I suggest you purchase a small tube of Loctite screw thread locker (or use some fingernail polish in a pinch), back out the main screws that hold the collars that hold the VESA mounts to the pole and lock these screws down TIGHT before attempting assembly or they might loosen up and allow the monitor to swivel horizontally after mounting the monitors. Also, since the metal parts look as if they are powder coated, the screw holes on some mating surfaces might be a bit difficult to get started, so before you are trying to balance a monitor and start a screw into a mating hole, run these screws in and out of them to clear out any manufacturing over spray in the threaded holes. Makes life easier... If you are doing this by yourself, as I did, I found the easiest way to mount the bottom monitor to the poles were to attache the VESA mounts to the monitor, stand the monitor on its side, resting on the desktop and then bolt the VESA mount to the collar. You only then have to pivot the monitor to horizontal and then tighten the collar around the stand pipe. The top monitor should be assembled to the VESA plate, attached to the collar, roughly leveled and then lowered over the pole to the correct height. It"s tricky but it can be done by one person. Be prepared to spend some time adjusting and re-adjusting the height, tilt and level of each monitor to get them just right, as they lock in place and are not adjustable when fully tightened. Also, be aware that if one of your monitors has a connection you use that sticks out the back of the monitor at a 90 degree angle in line directly under the VESA mount, you will have trouble tilting the monitor down. My uppermost monitor had such a cable and it took some finessing to get it in place with the stiff video cable sticking out and hitting the support pole, but I was able to make it work. My only concern now is that I might have a stiff neck from looking up at the top monitor for long periods, but considering my other options (basically none), I"ll have to learn how to deal with it... All in all, I am quite happy with this stand and the price is more than fair.

I was going to write out my reasons for building a sit/stand before realizing that if you’re reading this article then you’ve probably already read up on the why in other, more interesting places.

In the right corner you can see my MBP in its vertical dock, taking up minimal space. The laptop is not actually powering the monitors, I recently built a Hackintosh desktop that is quite a bit more powerful. I may write an post on it later on.

This picture already shows my monitors mounted to the 3M desk mounts. I purchased two, but they have a single mount that you can place 2 monitors on. I decided to go with two separate mounts because I plan to purchase a 3rd monitor in the next few months.

This is what the arms look like behind the desk. The two monitor mounts are fully articulating. They can go up, down, around. The range of motion on them is quite nice and provides a great range of positioning. The work by using a counterweight system - you can actually move the 18lbs monitors around with a single finger, and they will stay where you want them to. I can also turn them into portrait mode.

They attach to the desk via a fairly powerful clamp that you can tighten. Once you tighten it, it is rock solid. I am completely confident in their ability to not drop my monitors, and not loosen their grip on my desk.

This is the Mount Factory arm, extended. It also has the Ergotron Quick Release LCD Bracket attached to it. The arm itself is VESA compatible - remember they are for monitors and other VESA-compatible items. I have attached the quick release bracket to it because I do not want the keyboard tray to be in the way when I am sitting down. It will make sense in a second.

This is the back of the keyboard tray. The quick release bracket is the black item. The big gray plate is the Monoprice adapter. I did it this way because the keyboard tray is quite large and I wanted to have more grip across a larger surface area. Nothing fancy to attach, just some short screws.

From behind you can see how high the monitors and keyboard are raised. For reference, I am 6’0” and everything is at a fairly comfortable level for me. Remember that the monitor arms cannot go any higher, so if you are much taller than me you should keep this in mind. 3M may sell some longer poles so you can adjust them even higher. Check with them!

If you go with all the same parts I did, and only have one monitor it will cost a total of $226.65. If you go with two monitor mounts it goes up to $383.64.

Of course, it will not be nearly as fancy, but it works and it really only takes about 60 seconds to go from a sitting desk to a standing desk with this setup.

While this whole project may not have cost a ton of money, there are some minor drawbacks you should be aware of. Height-limited - If you are exceedingly tall, you will have to hunt for pole extensions. Again, I am 6’0” and it works for me. Anyone shorter will also be fine.

Keyboard tray is slightly wobbly - You can tighten the screw on the keyboard mount so the tray does not move forward and backward (ie, pitch). However, I do not believe the mount has screws for tightening against the roll axis. When I type, the keyboard shows a slight wobble. It is not enough to actually annoy me, or interfere with my work, but if you are extremely picky and sensitive to this things it may bother you. I would expect most people to not notice after the first few minutes of use.

Dual PC monitor setups aren"t necessarily a thing of the past, but ultrawide monitors are arguably the zeitgeist when it comes to efficient multi-tasking, increased productivity, and immersive gaming experiences. And while there are a number of options on the market, none may be as affordable (and effective) as Monoprice"s Single Monitor Adjustable Tilting, Rotating Ultrawide Monitor Mount.

The Monoprice Single Monitor Adjustable Tilting, Rotating Ultrawide Monitor Mount is designed to support today"s big and ultrawide displays up to 49" in size. And with a weight capacity of up to 33 pounds, it"s able to accommodate even the heaviest of monitors.

I was super excited to finally get to mount my LG 43" monitor on my desk, rather than using the factory stand. Desk real estate is always at a premium, so getting the monitor up and out of the way was a huge plus.

The monitor mount came well-packaged and included all the necessary hardware for installation. It was also very easy to install, taking me less than 10-minutes from start to finish.

Made of powder‑coated aluminum and steel construction, the mount feels like it"s built to last, with the heavy-duty hardware being perfect for any setup. It includes secure edge-clamp or through-hole mounting options (for a 1/4" hole) so you can find the right fit no matter what your needs are.

Once installed, the monitor mount is very sturdy and does an excellent job of holding the monitor in place, even when I adjust the monitor"s angle or position.

The monitor"s mounting head can rotate 90 degrees. With medium-sized displays, you may tilt the screen an additional 15 degrees to a maximum of 45 degrees in either direction for landscape or portrait orientation. To be clear, those additional angles can only be achieved with smaller mounts, like the 27" Acer Predator XB3 Gaming Monitor (which attached to the mount effortlessly).

Monoprice"s Ultrawide Monitor Mount has a number of nice quality-of-life features that help make it an attractive option, especially at its wildly affordable price point.

The built-in cable management system not only reduces visual clutter by bundling your cables together, but also hides them inside the vertical support. This prevents cords from becoming tangled and helps to keep your desk looking neat and organized.

A VESA mount is also included, allowing for use with other VESA-compatible monitors, and it"s worth restating just how durable and well-made this mount is.

Finally, and probably most notably, the price of the mount stands out when compared to similar options on the market. At just $39.99, it"s a fraction of the cost of other monitor ultrawide mounts, making it an excellent value.

If you"re looking for an affordable, reliable, and sturdy monitor mount that supports ultrawide monitors up to 49", the Monoprice Single Monitor Adjustable Tilting, Rotating Ultrawide Monitor Mount should definitely be at the top of your list. It"s easy to install, includes all the necessary hardware, and has a number of nice quality-of-life features that help make it an attractive option.

A product sample was provided to GamingPizza for this review. The Monoprice Single Monitor Adjustable Tilting, Rotating Ultrawide Monitor Mount is available on Amazon for $39.99, as well as on the official Monoprice website.

FeaturesFull Motion:Adjustments are easy to make thanks to the counterbalanced gas-spring arms. Effortlessly raise, lower, pull, push, and adjust your monitors with gas-spring assistance for the perfect working position and most comfortable viewing angle. Extra arm segments provide more adjustability and positioning options.

The Fully Jarvis Monitor Arm can support monitors up to 32 inches and about 20 pounds, with a wide range of motion and a solid build quality. Although there are nearly identical monitor arms that cost less, such as the Monoprice Workstream 15526, the Fully Jarvis was easier to set up, sturdier, and smoother to operate in our tests. It also adds three color options and a much longer warranty (15 years versus other companies’ 10- or even one-year warranties), so it’s an arm you can expect to support your screen for years to come.

If you have a 34-inch monitor or one that weighs up to 25 pounds, the Ergotron LX Desk Monitor Arm will work just as well. The LX has nearly identical side-to-side ranges, tilt, and pan and rotation capabilities as the Fully Jarvis—but its max height range is a few inches lower. If you’re over 6 feet tall, the Ergotron LX Tall Pole would be a better option for you. The Ergotron LX is nearly identical to the AmazonBasics Single Monitor Stand, but Ergotron’s warranty is 10 years, far longer than Amazon’s one-year coverage. We think paying for a longer guarantee is smarter than prioritizing short-term savings—a monitor arm should last you many years, and the company that makes it should stand behind it.