3.2 tft lcd shield in stock

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (3.2" diagonal) bright (5 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6206 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

※ Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

ER-TFT032-2 is 240x320 dots 3.2 " color tft lcd module display with ILI9320 controller and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 16-bit parallel interface. .FPC is soldering type,there is no need for zif connector.Lanscape mode is also available.

This 3.2 inch lcd screen adopts ILI9341 driver chip, and it is with 2x20P male headers interface, namely total 40 pins, so it supports mega 2560 board, but not compatible with uno r3, nano and esp32 board.

This 3.2 inch display works at 3.3V. If you use it with mega 2560, please insert TFT 3.2 LCD expansion shield, not directly connect board with the 3.2 inch screen. Otherwise, it"ll be burned.

This lcd expansion board is necessary for the 3.2" TFT lcd module to work with Mega 2560 development board, because the 3.2" TFT LCD works at 3.3V, if connect it with mega2560, the lcd maybe burned.

You can display bitmap images stored on the microSD card on the display. The shield is plug-and-play, assembled and ready to go. It uses a few I/O pins, which are:

Begin by carefully starting the rear connector of the TFT shield onto the Arduino Mega. Go slowly and ensure that all pins are inserted correctly and are straight.

In order to use 3.2″ TFT lcd  Shield , We must have the libraries. So you can download  (UTFT Library) and (URTouch Library) install the library by extracting that zipped file in the library folder as shown below.

Fully assembled 3.2inch display with 320x240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID-C1. 2x13 tall female header is already soldered on the PCB.

?MultiFunctional? Tft01 Lcd 16 Can Support The Current Mode, Since There Is Sufficient Mega2560 Io, While Using Only A Touch Screen Interface Or Sd Card Interface, Like In The Case Of Face 328S Will Not Exist.

?CHARACTERISTICS? TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard board, designed section TFT Shield, can be directly plugged into the board that use TFT01 LCD module.

?Good Effects? Tft01Lcd Supports 8-Bit Mode, Can Use Sd Card Interface And Touch Screen Interface At The Same Time, Adopts Ic Voltage Division, Makes The Tft Display More Stable.

?Widely Applicable? This Lcd Tft01 Mega Shield V2.2 Is Fit For 3.2 Inch Tft Lcd Module; The Tft01 Mega Shield Supports 16-Bit Mode; Because Of Mega Board Have Enough Pins For Using Sd Card And Touch Function At The Same Ti

3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and multifunctional module for your project. The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins. It is the version of product only with touch screen and touch controller.

Fully assembled 3.2inch display with 320×240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID-C4 / N2 / N2+ / C1 / C1+ / C0.

Fully assembled 3.2inch display with 320x240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID. 2x13 tall female header is already soldered on the PCB.