adafruit 128x128 tft display made in china

This lovely little display breakout is the best way to add a small, colorful and bright display on to your project. Since the display size is 1.44-inch and since TFT display has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

You don"t dismantle anything. Just look at the pcb side of your display. There will be some visible chips and some printed information e.g. model number.

The TFT display is a kind of liquid crystal LCD that is connected to each pixel using a transistor, and it features low current consumption, high-quality, high-resolution and backlight. This 1.44-inch full color LCD has a narrow PCB display. The resolution is 128×128 pixels, and it has a four-wire SPI interface and a white backlight.

@877dev TBH, I haven"t used this in ~2 years, so without trawling through the recent commits, I"m not sure where it"s at. The alteration was in the .cpp file, and it was to do with the initialisation of the display. There"s various displays on the market, each with possible subtle alignment differences and sometimes colloquially referred to by the colour of the tab of the removable protective film.

What"s going on is the display manufacturers are combining smaller TFT panels with larger driver chips, so when you init the display driver, you need to clip the driver"s display ram with a width, height, row and column offset. The same clipping is used to draw things like lines and rectangles.

There"s nothing stopping you from writing to the entire display ram, however, on smaller TFTs, you just won"t see some pixels and when you try to do high level operations like lines and graphics, they would be relative to the display ram size, not actual TFT pixels.

This lovely little display breakout is the best way to add a small, colorful and bright display on to your project. Since the display size is 1.44-inch and since TFT display has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

LiquidCrystal fork for displays based on HD44780. Uses the IOAbstraction library to work with i2c, PCF8574, MCP23017, Shift registers, Arduino pins and ports interchangably.

The most powerful and popular available library for using 7/14/16 segment display, supporting daisy chaining so you can control mass amounts from your Arduino!

A simple library to display numbers, text and animation on 4 and 6 digit 7-segment TM1637 based display modules. Offers non-blocking animations and scrolling!

Monochrome LCD, OLED and eInk Library. Display controller: SSD1305, SSD1306, SSD1309, SSD1312, SSD1316, SSD1318, SSD1320, SSD1322, SSD1325, SSD1327, SSD1329, SSD1606, SSD1607, SH1106, SH1107, SH1108, SH1122, T6963, RA8835, LC7981, PCD8544, PCF8812, HX1230, UC1601, UC1604, UC1608, UC1610, UC1611, UC1617, UC1638, UC1701, ST7511, ST7528, ST7565, ST7567, ST7571, ST7586, ST7588, ST75160, ST75256, ST75320, NT7534, ST7920, IST3020, IST3088, IST7920, LD7032, KS0108, KS0713, HD44102, T7932, SED1520, SBN1661, IL3820, MAX7219, GP1287, GP1247, GU800. Interfaces: I2C, SPI, Parallel.

True color TFT and OLED library, Up to 18 Bit color depth. Supported display controller: ST7735, ILI9163, ILI9325, ILI9341, ILI9486,LD50T6160, PCF8833, SEPS225, SSD1331, SSD1351, HX8352C.