bad tv lcd panel symptoms supplier

Since TV is used practically everyday for hours at a stretch, it is bound to have some issues over time. Some of these issues can be taken care of at home, while some serious issues may need help from a professional.

If you notice vertical lines on your TV screen, this is a serious issue and should not be neglected. This problem usually occurs if there’s a loose cable wiring, loose or faulty board or a damaged screen.

This is a common problem in TVs and is a sign that your TV panel is failing. But before you call an expert to check the TV, you could try following these steps and check if they work:

Turn off the TV and unplug the AC power cord (main lead). Keep it unplugged for 15 minutes and then switch on the TV to check if the issue has been resolved.

If it continues to show lines, you may mostly have to get the panel replaced and replacing the panel can be a costly affair, depending on the TV and its model. LED panels range anywhere between Rs 8,000 to Rs 85,000, while LCD panels range between Rs 6,000 to Rs 25,000.

Try increasing the volume to the fullest on your remote to check the sound. Ensure the TV input is correct, the TV is not on mute mode or no headphones are connected to the TV audio out jack on the side or front of your TV.

Also, check if all the cables connected into the back of your TV are proper and not loose. If there is still no sound, you will need to call a professional to open the TV and check the circuit board.

When the TV has speakers that work perfectly fine but it has no picture, there is mostly an issue with the back-lighting system or the power supply board, which will need to be replaced. In the case of an LCD TV, it works with the help of a backlight that is used to illuminate the picture on the screen. When the backlight begins to have problems, the screen turns blank.

To fix this issue, the backlight will have to be replaced by a TV expert. Another possible reason is that the backlight on the LCD TV which has a power inverter has failed. When this happens, you may need to replace the inverter or the capacitor.

This is again a common issue that most people complain about. While switching on the TV using the remote, if you notice that the light blinks but the screen is blank, this is an electric connection-related issue.

You could try disconnecting the power cord from the unit and wait for 10-15 minutes before you plug it back in. If this is just a simple electric connection problem, this should fix the issue. If the screen still doesn’t turn on, you will need to call a TV expert to resolve the problem.

There could be several reasons for a flickering TV screen, which is mostly a common issue with LED TVs.One of the major reasons for this is loose or defective cables that result in screen flicker.

Be it a panel issue or a major technical issue with the TV, resolving these problems is a costly affair. It’s best not to ignore any of these signs and call an authorized TV expert before the problem worsens.

Buying a television is a long-term investment, so do not compromise. Buy one with a minimum of 4K resolution because new technology like OLED and HDR is pretty much only on 4K TVs.

Choosing a TV size plays an important role. If the screen size is too big for your room, you may notice the loss of clarity. To measure the distance between the sofa and the TV. If the viewing distance between the sofa and your TV is between 5 – 10 feet, a 40 – 42 inch TV should be perfect for your room. If the distance is less than 5 feet, a 32 inch should work best.

Don’t just ask for a smart TV. Most TVs available today are smart TVs with easy access to Netflix and other online apps. So do not be tricked into buying one just because its a smart TV.

2. #Confirm whether the VAA is normal (normally about 17V). If abnormal, disconnect the RP32 to confirm whether it is caused by DC/DC loop or X-side COF: disconnect RP32, if the VAA is normal, the COF is bad, CO must be changed; COF can be Disconnect one by one to determine which NG disconnects RP32, VAA NG, try to change UP1; at the same time, confirm whether the continuity of the surrounding triode is OK.

4. #Press the LCD glass side of the panel, if the vertical lines disappear or reappear, it can be judged that the cause of poor contact, OM checking should be able to find the poor contact.

The above is the full text of LCD screen failure repair guide, we hope it is helpful to you. If you need to buy LCD and find a reliable LCD supplier, we suggest you to read our other great blog – How to find a reliable LCD supplier.

Founded in 2014, VISLCD is a professional LCD supplier. We provide LCD modules, touch LCD and customized LCD in various sizes with stable quality and competitive price. Welcome to contact us for any LCD demand, thank you.

The difference between a LED TV and a LCD TV is that they are both LCD TV’s except one has LED stripes and the other has CCFL Backlights- (Florescent Tubes). I used a Philips Magnavox Emerson LG TV when testing these repaird, but they should work on other TV brands that are similar. Before you do any Repair, check to see if you are still under warranty, or are covered by a recall of your TV!!

If your Plasma or LCD/LED or CCFL/LCD TV or monitor has stopped working, or is displaying one of the following symptoms, then it *may* need some new capacitors in the power supply board or a replacement board

-Upon three unsuccessful start up attempts the TV locks itself in protection mode and needs to be disconnected from AC for 30-40 seconds before power attempts can be restore-Display Locks after 10 minutes–

1) the front green LED of your TV comes and stays on for 20-30 seconds, then turns off for 1-2 seconds and then keeps cycling like that, but the display never comes;

2) the display comes on for a brief few seconds, then the TV shuts off; in some models the display may not even come on, but still the relay clicking on and off and the green power LED activation and shutdown can be easily observed.

A model number is needed to determine the unlock procedure, but most likely you will need a remote to unlock most TV’s. Below is a common lock procedure.

Choose On to disable all the buttons on the front of the TV. FPA Lock On will appear on the TV screen each time you press buttons on the front of the TV. You can still operate the TV with the remote control. You can still use the POWER button on the front of the TV, but only to turn off the TV (not on). Set FPA Lock to Off to cancel this feature so you can use the buttons on the front of the TV again.

3. Press and hold each of the remaining buttons on the TV, one at a time, for about five seconds, and then release. DO NOT use the buttons on the remote control - only use the buttons on the TV itself.

6. The TV should start automatically scanning for active channels from your input signal source. Make sure you have a good signal (antenna or cable or satellite).

If the TV still does not display anything, try the menu button on the TV and see if you can access the menu. If not, try using the remote control’s menu button.

If the TV is still locked and will not respond to any commands from the front panel control buttons or the remote control unit, it is apparently locked in a failure or diagnostic mode, and would probably have to be diagnosed and repaired by a reputable TV repair facility. Good luck.

If it is a thin vertical line that appears on certain video resolution/image then it is normal and is indicated in the users manual under troubleshooting. If the line is almost half the screen, it could be a problem with the cable connection between the LCD panel and logic board, or the LCD panel itself. Try reseating the cable first if it’ll solve the problem. I’ve done similar issue in the past. Reseating the cable worked for a couple of months till eventually the LCD panel is the problem. Replacing the LCD panel is quite costly and impractical.

If the lines are there all the time or intermittent but in the same location it is an indication of a bad panel. The panel driver can also be the cause of this symptom.

If the lines/bars are across the OSD Menu, and all the video signal inputs also same result, that means the TV LCD Panel is defective Most of the time this symptom is caused by a bad LCD Panel 95%. You can try refitting LVDS Cable or replacing Main Board capacitors or replacing Main Board—5%

Bad news unfortunately, their are two possible causes for what you have described, one would be a fault with the picture drive pcb ( Power Control Board ), and the other is physical damage to the LCD cell matrix, (screen).

There’s videos on how to fix this. It has to do with putting foam, in between panel frame and screen, which applies pressure to solder joints, which then completes the circuit- Contact my10cents, for better explanation.

Big Black Bar on bottom of TV Screen– If the bar that appears in the bottom is showing the energy saving logo, HDMI, Dolby surround and pc mode capabilities look into your remote.

Is the OSD menu affected as well? If yes then possibility could be the LCD Panel or the t-con board. Since you have replaced the t-con board then possibility is the LCD panel. There could be also a possibility of mainboard where upgrading the firmware could restore the picture. If the OSD menu is not affected then the LCD panel is good.

If the lines are across the OSD menu then chances is very high the LCD panel is the cause of the problem otherwise it can be due to bad T-con board or even Mainboard. Have you tested on the OSD menu to see if the lines are really across the menu?

White Lines– There are several possibilities that can cause white lines on an lcd screen. One would be high temperature on the logic board. Logic board drives the LCD panel and when it overheats can cause this display problem. One solution would be to clean the vent holes around the TV. One possibility that I have experienced myself servicing is a bloated capacitor on the power supply board. The worst possibility is a defective LCD panel, which is costly to repair, and sometime more practical to buy a new TV set.

Do you get blue screen when using x-box or DVD, VCR? Have you tried to reset cable box if you have one? Reset TV. Check all cable connections? Try these first.

Do you use the Set top box for cable channels? If yes then try connecting through HDMI and see if you can see the TV. Also do you get blue screen when using x-box or DVD, VCR?

What made you decide to change the mainboard? I ask because if the MENU does not appear, then this indicates a problem elsewhere within the TV. Also, did you check for any swollen, or bulged capacitors on the power supply board?

There are several problems that could cause this problem. It could be the connection from the T-Con board to the panel, try wiggling these cables around and see if the picture comes up even for a second. The Mainboard or it’s cables are not the issue in my opinion. The isdsue is either going to be a bad capacitor, faulty output from the power supply to the T-Con board, a bad connection from T-Con to panel, or the T Con or the panel itself are faulty.

Basic things you can do is to check the connections. If you have a cable box, check the video connections. And while doing that, unplug the TV and the cable box from the AC outlet for it to reset. These are the most likely cause of a blue screen

Most of the new TVs display a blue screen when theres no signal for it to lock on. Try unplugging it for about 5-10 minutes and see if that clears up the problem. Why? Because they have microprocessors in em (computer chips) and just as like with any other operating system, they can hang up or crash. This isnt an uncommon problem with todays TV sets. Unplugging it for awhile resets the microprocessor (in other words, it causes it to re-boot when you plug it in again).-

It could be the connection from the T-Con board to the panel, try wiggling these cables around and see if the picture comes up even for a second. The Mainboard or it’s cables are not the issue in my opinion. This is due to either a bad capacitor, faulty output from the power supply to the T-Con board, a bad connection from T-Con to panel, or the T Con or the panel itself are fault. Also, it’s possible the A/V receiver’s Video On feature was turned off by an electrical surge or something else.Turn the Video feature back to On and suddenly that bad blue screen was gone.

Repair/Solution: Change the cable box to a fixed resolution. OR have the customer install the latest TV firmware which can be located at your TV Brand Customer Support

Your power board needs serious help–If you want to repair you have to replace Switching Mosfets, disc capacitors and of course the main fuse, Rectifier Diodes and most of the time the transformer–Costly–Easier to replace Power Board–There is a chance the strike come through the cable line, so it’s possible the Main Board needs repair–That’s a small chance though, but I thought I’d let you know–Replacing power board should repair your TV. During a lightning storm, electrical power surges is induced to the transmission line eventually end to our household appliances. Our TV sets, computers are the most susceptible. For the TV set, the basic cure is to leave the TV unplug from the AC outlet for it to discharge and reset

5. wait another 30 seconds and some type of picture should appear—If that does not work–Unplug TV for 10 minutes and then hold power button on TV for 60 seconds–Plug in and turn on.

Unplug TV– On TV, hold the power button down while pushing and holding each button for a few seconds. After going through all buttons, (on TV) then plug TV back in and it should power up–

When the TV, has no Picture or Sound. Led turns from red to (Blue or Green). It means the Main Board has sent out the start up signal to the PSU (Power Supply) Board.

Now we need to know if PSU Board has all the correct output voltages. This means checking the secondary side output voltages of Power Board. Probable causes are the Power Supply, the T-Con board, Main Board or the LCD panel itself has failed.

No Picture/Sound The person who looked at my TV, stated that the high voltage power supply needs to be replaced. He explained that I have a low voltage supply which is why the power button is lit once pressed, and a high voltage supply which needs to be replaced.

You will have to go into the TV and check for capacitors or burn marks or cracked solder around the pins–Main board could be IC’s, or regulators–Panel–Disconnect panel and see if your TV stay’s on—

The flashing green light indicates a fault on the power board inside your TV. This will be due to a faulty component like a capacitor or voltage regulator. Faulty electrolytic capacitors on the power board are the most common cause of this problem. These capacitors will often leak and stop working as the TV set gets older,but could also be caused by the Main Board or the inverter board. (LCD TV ONLY) So we will have to take a look inside and maybe do some circuit testing and a visual of your boards-

In a dark room take a flashlight and at an angle shine it on the screen and see if you can see any movement. If you can see movement or see your menu then its backlight failure. If totally black screen with sound then its T-Con board. So if you see movement on a led screen, then it’s your LEDs inside the panel. If on a LCD TV you see movement and lamps are not turning on, replace inverter. If with a LCD TV your lamps turn on, with no picture replace T-Con Board.

Plasma is the most durable in terms of panel failure. LED/LCD is terrible for panel failure. (But every model gets bad apples. Samsung LED/LCD panels die frequently. LG panels are a lot more reliable.) Overall I’d say plasma is more reliable, and even if it fails, in most cases plasma is repairable, LED/LCD is expensive to repair and often difficult to troubleshoot.

A blurry image on a high-definition LCD TV is typically the result of a mismatch between the TVs resolution capabilities and the resolution of the signal that is coming from connected devices, such as a DVD player or satellite TV receiver. Typically, blurry pictures result when a peripheral device connects to the TV through non HD cables and jacks.

If your TV isn’t working properly, there are still a few things to consider before you give up on it. Generally, you’ll have a few warning signs that things are not exactly right.

Of course, sometimes, the TV is beyond repair and you should replace it instead. If the screen is broken or the TV doesn’t turn on no matter what you do (or if the sound stopped working completely), it’s time to check out a new set.

The difference is that stuck pixels usually happen because of a problem with a transistor; they often have different colours and are usually just simply out of place. If it is a dead pixel, then the TV should be sent for repairs, as, unfortunately, the issue is a difficult one to fix.

If the colours on your screen appear distorted, then your TV might be malfunctioning. Traditionally, this issue tends to occur gradually, meaning that you might not notice any difference at first. This is due to the common factor that one colour tends to weaken at a time; therefore, no obvious changes happen overnight.

If your screen starts to display bars and lines, this tends to indicate that there is an issue with a connector. This can occur when something magnetic has been placed near the TV and, in turn could mess with the picture quite considerably, even potentially de-magnetising the screen.

The issue can be due to cables that have become loose inside the screen as well, which is an easy fix, although it may require a professional because the TV may have to be opened.

You may be able to do something about this by adjusting the levels of brightness and contrast on your TV and playing different types of content to see if the problem goes away. You can also enable your TV’s Pixel Shift feature; when this feature is turned on, images on the screen move a bit to vary the pixels used. Pixel Shift is often included in modern sets and might clean out the phantom image.

This issue could occur if the signal received is a digitised standard (480p), as there’s a discrepancy between the resolution and the display. It’s also worth noting that the digital signal your TV receives can be affected by weather conditions as well, so the image can appear fuzzy and glitchy.

However, the good news is that, when this happens to modern televisions, there is a high chance of it being fixed, so you can still enjoy your TV for a long time.

If the TV is on but the picture is faded on some areas of the screen, it’ll be difficult for you to actually enjoy the content. You may try to ignore the stain-like mark but there is no denying that this will impact your experience. Faded spots are not that rare and can be accompanied by other serious issues, like your image fading to black after you’ve turned the TV on.

We offer repairs as well as a vast range of products so, if you find that your current TV is well past its sell-by date, be sure to browse our amazing

If you’re worried that your LED TV is dying, then you’re not alone. Blinking, flashing, blurred lines, and a variety of others symptoms might be a sign that it’s time to get a replacement. Fortunately, you can fix a lot of problems without getting a new one. Nevertheless, it’s important to know when something’s wrong.

The signs and symptoms of a dying LED TV include dull, faded, blinking, lined screens and delayed communication services. Other problems include distorted colors, dead pixels, and burn-in edging. Although it’s rare, another symptom includes high-pitched noises from the screen.

Perhaps the most impressive part of owning an LED TV is that they do everything almost instantly. The remote communication responds immediately, the pixels brighten up with color, and the images are crisp. Unfortunately, this makes it very easy for you to notice small issues, such as a long wait time.

If you turn on the TV and it takes forever, it could be a remote issue. The signal needs to be strong and unblocked. However, it’s typically a symptom of a dying LED TV. The pixels aren’t able to respond to the command, which leaves them looking worn and dull.

When you turn on an LED TV, you should expect high-quality images that show up instantly. If you’re getting anything other than that (as you’ll see throughout this page), it’s a huge sign that you need to get it repaired or replaced. Since TVs are heavily sealed these days, it can be hard to DIY the repairs.

Nobody wants to look at a dull TV screen. The biggest reason that people want to invest in an LED TV is that they want the vibrant, bright, detailed images promised by countless companies. Unless the TV has a low pixel count (which is very rare with LED screens, especially those produced within the last five years), then you might need to get a new one.

Dying color bulbs could be a huge cause of a dull screen. This could be a result of an old screen. LED bulbs are designed to last for a very long time, but like all other TV screens, they won’t last forever.

When someone runs into the TV, knocks it over, or hits it with something sharp, it could break or damage the bulbs. This process leads to a dull screen since it’s nearly impossible to repair the inside of modern TVs.

Sun fading is no joke. If your TV is positioned in direct sunlight, it can dull the screen quickly. Much like sun bleached clothing, LED screens are capable of being dulled and having their colors stripped.

Have you ever started watching TV and it suddenly shuts off? Fading is also a common issue. Both of these problems are associated with a TV that’s on its way out. If your TV is always faded or randomly cuts to a much lower resolution, then it’s probably not going to see life much longer. You’ll need to get a new set within a few months.

The good news is that, if you don’t mind it, you can stretch the lifespan of a faded TV for a long time. The biggest issue is when it starts to randomly fade and turns itself off. If this issue occurs, then there’s not much you can do. It’ll continue to fade and shut off more often until it doesn’t last more than a few seconds.

If you catch the error when it starts, you might be able to save it. There are plenty of TV repairmen that claim that they can handle the problem. You might be able to spend $50 to $100 instead of the thousands required to replace large, top-of-the-line LED TVs.

Similar to the previous sign, if your TV blinks randomly, you might have a serious problem on your hands. It could seem like a blink sometimes. Many people miss this issue because it’s so sudden and random that they mistake it for a flickering light. You’ll notice that it happens more often, which is when you need to get it fixed.

Much like a faded screen, you can have it fixed if you catch it in its early stages. Failure to do so will cause the TV to shut off, become discolored, or completely die. Blinking is caused by dying cells or flickering LED bulbs. The more bulbs that fade out, the more blinking you’ll have. Keep in mind that the blinking could be concentrated in one spot or spread throughout the TV.

Although it’s not as common, the blinking might occur around the edges of the TV. Since the bulbs are sometimes put under pressure near the sides, top, and bottom of the screen, improper placement could cause them to lose power much sooner than they should.

You might also notice flashing in one spot of the screen. These concentrated bouts of flashes, blinking, dulling, and similar issues can be a sign that the cells of your TV aren’t looking too good. They’re a telltale symptom of a dying TV, regardless of if it’s an LED or any other type of television set.

When you see these flashes, it’s time for a new TV. it’s very rare that you’ll be able to fix this issue. Fortunately, most high-quality LED TV screens are designed to last for many years without any signs of this once-common problem.

Most modern TVs have built-in speakers, especially high-end LED sets. If the speakers start to fail, it means that the TV is on its way out. There are several causes of failed sound quality, including the following two issues:

Playing the sound too loudly through the speakers will cause them to blow out. Many people have heard about playing speakers with too much noise, ruining the internal components. LED TVs aren’t immune to such issues.

The remote or on-screen buttons aren’t communicating with the TV. These problems can be fixed by dealing with the remote or the receiver. You usually don’t have to buy a brand-new TV, in this case.

Rent a Center explains that screen burn-in is one of the biggest issues of owning an LED TV. While it’s rare, an LED TV can experience this symptom that shows fading around the edges of the entire set. It’s known as a ghost image for many reasons, mainly due to the dull images that remain from previous channels.

For example, if you always watch the news, the logo might be ‘burnt’ into the bottom corner of the screen. It maintains the same image, even if you switch channels. You won’t likely see the colors, but the outline can be seen whenever you have the TV turned on. There’s not much you can do since it’s irreversible.

One way to prevent this problem from happening is to ensure that your TV isn’t on all day. We’ve all had the habit of leaving the TV on when we go to school or work. However, long-term misuse can cause it to overheat, burning the image onto the screen.

This symptom is the most obvious issue that it’s time for a new TV. Whether the crack shows up on the screen or the edge of the plastic, it can’t be repaired. To make matters worse, LED screens are known for spreading cracks very quickly. Even if it looks small, a few bumps can cause the crack to become bigger.

The good news about cracks is that they’re often covered by manufacturer warranties. That doesn’t include if you throw a rock or even a Wiimote at the TV, but you get the point. If the set arrives with a crack, then you’ll be able to contact the company to get a repair or replacement. Make sure you ask about warranties and guarantees before you buy a new TV.

Every TV screen is made out of a series of pixels from end to end. If you don’t know it already, the resolution is composed of these pixels. For example, modern 4K UHD TVs are made of over 3 million pixels. The more pixels there are, the higher the resolution and the clearer the image will be.

Unfortunately, damaged pixels start to form lines. You’ll notice that the pixels are bigger in some spots than others. When one pixel breaks or goes bad, it could spread to nearby pixels. Electronic World TV shows us that this issue is far more common than you might think. To make matters worse, it’s very difficult to fix.

Much like the other problems on this list, lined pixels are a result of misuse. When people throw things at the TV (I’m looking at you Wii and Switch owners), drop it on the ground, or expose it to too much sunlight, the pixels become damaged. You might notice lines, bumps, and clusters.

An LED TV’s signal is a major part of its function. Nobody wants to have to stand up and walk over to the TV every time they want to change the channel. In fact, a lot of new TVs aren’t made with channel buttons aside from the remote. If your set isn’t communicating or responding to the commands, there’s no purpose in owning a TV.

Thankfully, this issue is one of the few repairable symptoms. It’s usually a matter of getting a new remote, replacing the batteries, or fixing the TV’s receiver. All three of these problems are relatively inexpensive, especially when compared with the cost of a brand-new LED TV. You can test the theory by replacing the batteries, then moving to the next suggestion.

The downside of this error is that it’s not always able to be fixed. If it’s not the remote, batteries, or receiver, then it might be the LED screen. The bulbs don’t want to turn on because they’ve been permanently damaged. In this case, it’s time for a new TV.

Nevertheless, it’s worth hanging onto the TV until you find out if it can be fixed. Call a TV repairman or call the manufacturer to figure out if they have any recommendations. That suggestion applies to any of the signs and symptoms of a dying LED TV.

Overexposure to bright lights (whether they’re natural or artificial) can cause the screen to lose its brightness. Another common cause is that people tend to turn up the brightness on their TV too often. If you’re used to adjusting the lights in your TV, then consider that it could be causing permanent damage.

Remember that blurriness or fuzziness could be as simple as a bad TV signal. It’s not always the fault of the LED TV, so you might want to consider the typical connectivity issues in the area.

Low-quality LED screens don’t have the same cutting-edge technology and protective features. If you cut corners and tried to get a budget-friendly TV, then there’s a chance that the screen wasn’t installed correctly. The result will be a warped, wavy TV screen. You can notice it better if you look from the side of the set.

Another cause of warped, bubbly LED screens is when they’re exposed to too much heat. There’s a lot of plastic used in the production of TV sets. Whether you’re leaving it on for too long or exposing the screen to excessive amounts of sunlight, it could start to ripple. It looks worse as the months go by.

There’s no way to fix a warped LED TV screen. If you notice it, then the best bet for a longer-lasting TV is to remove the heat source. On the other hand, those who got the warped screen issue right out of the box should contact the manufacturer to request a warranty repair or replacement.

If you’ve ever noticed a high-pitch hiss or crackling sound coming from your TV, there could be all sorts of causes. One of the most common issues is when you turn the brightness too high. The bulbs will be maxed-out, ruining the image. If you have a low-end LED TV, this problem is much more likely to occur.

The sound could be coming from the internal components of the TV, though it’s unlikely. Again, low-quality sets have a host of problems that are unexplainable and frustrating. The best way to prevent any of the issues on the list is to get a high-end, manufacturer-backed LED TV.

Note: Hissing or crackling from a power strip or plug from your TV is a safety hazard. Turn it off and unplug everything. Examine the power brick and the outlet to ensure that you’re not overloading anything.

As you can see, there are plenty of signs that you need to keep an eye out for when you’re owning and maintaining an LED TV. Sadly, most of these symptoms are the start of an irreparable deterioration process. Most of them are avoidable if you practice safe TV usage suggestions.

When it shows problem, few seconds after turn on the TV, either 1/10 of screen shows shadow (LCD still shows image) that looks like partial backlight out or entire backlight goes off (Still I can see lcd is working when I put flashlight).

So I was going to replace the power supply board but I also read an article saying that some TV shuts off when there is bad led bulbs in the back light.

Repairing your TV can be a little tricky, but with the right diagnosis and part number(s) and a few tools, almost anyone can fix their TV and save money. We"ve helped everyone from kids (with some adult supervision) to grandparents successfully repair their TVs! Now it"s your turn -- here are some tips to help you get started on your TV repair journey.

An accurate diagnosis is the first step in fixing your TV. Once you figure out what"s wrong with your TV, you can narrow down the defective part(s) that"s causing your TV"s symptoms. A quick Google search of your TV model number will help you figure out if your TV is an LCD, LED or Plasma model. Once you know your TV type, use these videos as general guides to help you properly diagnose and repair your TV.

DLP TVs can be difficult to move around, but they"re relatively easy to diagnose and fix. In this section, we list our popular DLP repair videos by part and brand.

We always, always recommend searching by part number. It"s okay to start searching with your TV model number, but the most efficient way to find the exact replacement TV part for your TV model is via part number. If you need help searching our website, please visit our Help Me Search page.

The most common reason is that your TV is on the wrong input. You can typically change the input by pushing a button on your TV remote labelled “input”, “source”, or “TV/Video.” Keep pushing the button to cycle through the inputs until you have your picture back.

There’s nothing more annoying than when you see someone’s mouth moving, but what you are hearing is not in sync. You see someone’s mouth say “hello,” but then you hear “hello” after the mouth stops moving. It’s like watching a foreign film with a voice-over. You will want to go into the audio settings of your TV or cable box and adjust the “audio delay.” This should get you back in sync.

If you’re hearing an echo, you probably have a separate sound system, like a soundbar or surround sound system and you have the volume playing both through your external sound system AND your TV speakers. If you have a separate sound system, you DO NOT want to also have sound playing through your TV speakers, as it will always result in an echo, plus you paid for that separate sound system because it sounds so much better than your TV speakers. You will want to disable, mute, or turn the volume all the way down for your TV speakers and only use your external sound system. This should eliminate the echo.

If your TV picture is breaking up, cutting in and out, or pixelating (looks like everything is a bunch of squares), then you probably are experiencing a weak signal. Check all of the connections from the wall to your cable box and from the cable box to your TV to ensure that all connections are tight. If you’re still experiencing issues, you’ll need to contact your cable or satellite provider.

If your screen has lines, bring up the TV menu. If the lines run through the menu, or if the screen is cracked, your panel needs to be replaced. This is not a cost effective repair. If you have an extended warranty and there are lines in the panel, the warranty company will likely replace your TV. If the screen is physically cracked, this would not be covered by a warranty and you will unfortunately need to replace your television.

Note that if the plasma screen is broken or crashed, it’s not repairable anymore. If this is the case, the TV needs a screen replacement, which may cost you more then the plasma TV itself. (A new screen price is around 2 -3k).

This issue is not repairable and you will need a new screen (PDP panel). That’s why for all those restaurants, bars, and public places, it’s better if you use an LCD type TV, not a plasma.

For example, a Panasonic plasma TV was in a King County bar for 6 months on a sports channel and it developed a burn-in sport channel image. The estimated cost for this type of problem would be $2,500.00. Be smart and save your money!

LED and LCD TV Repair is it worth it? For a lot of people who are using LED or LCD TVs, there is a real fear about breaking. Anyone who has owned an expensive and high quality piece of technology knows that there is a good chance a break means it cannot be repaired. However, this “common” knowledge is actually an assumption that isn’t rooted in much fact. With the right professional, it is possible to get your television working again without any problems. More importantly, you can do so without having to worry whether or not you have to buy a fully new TV!

If your TV panel is still in one piece, meaning a brick hasn’t gone through the screen there is a good chance it can be repaired! A lot of common issues such as power, audio, HDMI can be fixed.

The most important part of any LED TV repair is to figure out what is wrong with the product in the first place. Imagine a scenario where your television suddenly stops working and you think it is broken and thus throw it out. In some cases, a LED or LCD TV repair job means looking at the software and seeing whether there is a quick fix.

However, sometimes it is more likely that you need the help of a professional to diagnose the issue. Some places offer a free diagnostic of the LED TV so that you can learn for free what the problem is. Then you can choose to have them fix it or another reputable provider.

There are some people who claim to have expertise in a certain field, but actually do not have many credentials. You want to make sure that you find a professional for LED TV repair so that you don’t end up with an even worse television or being wrongly told that you cannot fix it. There is a risk of finding a poor quality LCD TV repair person so make sure that you are able to find someone who knows what they are talking about.

One great way to get excellent LED TV repair is to make sure you call in advance and speak to someone on the phone. You can discuss their credentials or, in some cases, even visit the location to find out whether they have any good knowledge of the subject. Sometimes local cities and organizations will offer awards to companies that show particularly good service and support for these type of electronics.

If you can’t figure out what is wrong with your television or you just want to get the opinion from an expert, it’s a good idea to start looking for local shops that can help you. Even if you have to travel a bit to find a good quality LCD TV repair person, you’ll welcome it in the end when you are at home with a fixed television that is as good as new.

Please Note – We kindly ask that you don’t contact us If your TV is damaged. We are not in the business of repairing TV’s and this post is for informational purposes only.

Enable the highest bandwidth setting on the TV. TVs will have settings for "HDMI Mode", or something similar, where you can choose between "1.4", "2.0", or "2.1", or have other settings called "Full Color" on Vizio and "HDMI Ultra Deep Color" on LG. This represents the TV"s bandwidth; an HDMI 2.1 source won"t display properly if you set the TV to "1.4", as you"ll be limited in the resolution and frame rate. You should always enable the necessary bandwidth because even setting it higher than needed can cause compatibility issues.

Make sure your source is playing HDR. You may see Dolby Vision or HDR10+ logos from streaming apps appear when you first play the content. However, not all TVs do this, and they don"t specify which HDR format is playing, like on Samsung TVs.

Check to see if the TV supports the format your content is in. LG and Sony TVs don"t support HDR10+, while Samsung doesn"t support Dolby Vision. If it doesn"t, it will usually end up playing in the basic HDR10 format instead.

Note: TVs should usually automatically switch into HDR when content is played. If not, check to see if there are any HDR settings or contact customer support.

TVs only allow for low input lag when in Game Mode. Outside of Game Mode, input lag is higher, and although most people won"t notice any difference, changing it into Game Mode has a positive effect on reaction-based games. Make sure the TV is either set to the Game picture mode or Game Mode is enabled; the specific settings depend on the brand. For example, Hisense, Sony TV, and LG TVs have a Game picture mode, but other brands like TCL have Game Mode toggles that you can use with any picture mode.

Restart the TV. Even in Game Mode, there may be a bug that doesn"t put the TV in Game Mode. For example, the Sony X800H has an issue where it has high input lag if you turn on the TV and it"s already in Game Mode; you need to switch it out of Game Mode then back in for it to work.

Check to see if it supports it. The Xbox Series X has support for Auto Low Latency Mode (ALLM). This allows the TV to switch in Game Mode when you launch a game from a compatible device for low input lag, but you need to make sure the TV supports it. If not, there"s nothing you can do. Sony TVs don"t have ALLM support but can detect when the PS5 is connected, and they automatically switch into Game Mode, but only if you enable Auto Picture Mode.

The same concept as ALLM setting: check to ensure both the console and the TV support the same VRR format. The Xbox Series X supports FreeSync and HDMI Forum VRR, so G-SYNC doesn"t work with it.

Note: For both ALLM and VRR, we check with the PS5 and Xbox Series X to see what signals the TV supports from the consoles. It"s best to check our reviews to see if your TV is compatible with either. For example, you can see the Samsung QN90A QLED"s compatibility photos with the PS5 and Xbox Series X.

If it"s a TV we tested, check to see if it properly supports chroma 4:4:4. This is a type of signal that helps increase text clarity when using it as a PC monitor. Sometimes, a TV simply cannot display chroma 4:4:4 properly.

Set the TV to PC Mode. This is often the best way to display 4:4:4. Roku TVs automatically switch the TV into PC Mode when a PC is connected. For most TVs, you"ll need to change the input label for the input you"re using to PC for it to enter PC Mode.

Increase ‘Backlight’ setting (‘Brightness’ on Sony and Samsung TVs). Keep in mind that some TVs have both the "Backlight" and "Brightness" settings. The "Backlight" setting increases the intensity of the backlight, but "Brightness" (or "Black Level" for some brands) is an image processing setting, and we don"t recommend changing it.

Note: Lower-end TVs aren"t usually as bright as the premium models, so if you"re in a well-lit room and the screen is hard to see, it usually means it"s not bright enough to fight glare.

Disable motion interpolation. Motion interpolation is a feature meant to increase the frame rate of your content to match the refresh rate of the TV. However, if it"s not effective, it can drop frames and make the image look worse.

Reset white balance and color space adjustments to default. If you understand how to calibrate the TV, you should be able to provide the best picture possible to you.

Gently massage the affected area with a soft cloth to improve. Keep in mind TVs are delicate, and if you"re unsure of yourself, it"s better to simply not do it.

Adjust the local dimming setting to your liking. Often, if a TV"s local dimming setting is bad, it will cause blooming in dark scenes. Either lowering the setting or disabling the local dimming can fix this.

Note: Black uniformity on TVs varies between units, and it"s all about the luck of the draw. You can"t fix uniformity issues. Only LED TVs will experience these blooming issues as OLEDs have perfect black uniformity.

Usually, this has to do with the source and on the TV, so check the source"s settings. If you"re watching something like a YouTube video, it"s as simple as checking to see what resolution it"s playing at.

Often, if you open the TV and you see many stuck pixels, it"s better to return it. Pixels are stuck when they display the same color, no matter the content.

Sadly, there"s no way to fix permanent burn-in, which only happens with OLEDs. Burn-in happens after constant exposure to static elements for many hours without watching other content. So if you only use your TV to watch the news a few hours every day, your OLED may experience burn-in. However, we don"t expect this to be an issue for those who watch varied content.

Note: You also need to make sure your TV supports the specific audio format. As of 2020, LG TVs don"t support passthrough for DTS formats, so you can"t expect it to play that audio file.

Move objects away from the front of the TV (soundbar, Kinect, etc.). The receiver for the remote is often right underneath the center of the TV, so you need to aim at that.

Ever had your TV showing nothing but a black screen even if the audio was working? Unfortunately, that’s a common issue with low/middle-end LCD/LED TVs these days… Even more frustrating, this issue often comes from a rather tiny and cheap component that can be easily replaced. Most common issues are:

One of my relatives had this exact symptom happening all of a sudden. This problem on low-end TVs often occurs within the first couple years. As the repair costs for that kind of TV is pretty low, considering repairing it yourself might be a good idea!

That implies disassembling the TV to access the backlight which is between the LCD screen in the front and the boards in the rear. In my case, with a Samsung F5000, I had to process as follows:

First we have to remove the back housing to reveal the boards (from left to right: main board, T-CON, power supply) and disconnect the LCD panel from the T-CON board.

Note: Older TVs have neon tubes for backlight, which is thicker and less exposed to this kind of failure. LED backlight is the most common thing these days, but do not mistake an LED TV with an OLED TV. The first one is a classic LCD panel with a LED backlight, whereas the second is an OLED panel that doesn’t need any backlight as it is integrated in each pixels (making the spare parts much more expensive by the way).

For starters I’ll go with the third one, just to make sure there is no other issues with the TV, but afterwards it’s better to replace the LED with a new one, otherwise you might notice a darker spot on the image.

Once we have by-passed the LED, we can power the TV on. Careful! High voltage (200-300v) runs through the TV when plug, so be very careful how you handle it so you don’t electrify yourself!

Now we just need to unplug the TV, replace the LED with a new one and put everything back together. Just to be sure, we should power the TV back on and check that everything is fine.

There might be a lot of other root causes for similar symptoms, a black screen often looks like something very serious and therefore expensive to repair, but this case is the perfect example that taking some time to look for the root cause can sometime lead to a good surprise: here a 1$ fix!

Transporting the TV from a cold to a warm location or a sudden change in room temperature may cause moisture condensation, resulting in a blurry picture or poor color. Turn off your TV and wait a few hours before powering on again.

Some wide screen programmes are filmed in aspect ratios that are greater than 16:9 (this is especially common with theatrical releases). Your TV will show these programmes with black bands at the top and bottom of the screen. For more details, check the documentation that came with your DVD (or contact your programme provider).

Due to the thin profile of this television, the heat generated by the LCD panel backlight and supporting electronics will be more noticeable. This is normal operation and not a cause for concern.

Liquid crystal displays (LCDs) are the most widely used display technology. Their applications cover TV, mobile phone, appliances, automotive, smart home, industrial meters, consumer electronics, POS, marine, aerospace, military etc. LCD screen display problem can occur for several reasons.

Effect of environmental conditions on the LCD assembly. Environmental conditions include both the effects of temperature and humidity, and cyclic loading.

Effect of manufacturing process. With the development of LCD for more than 40 years and the modern manufacturing equipment, this kind if defects are getting rear.

Common failures seen in LCDs are a decrease in screen contrast, non-functioning pixels or the whole display, and broken glass. Different kinds of LCD display problem need to have different kinds of fix methods or make the decision not worthwhile to repair.

Broken glassIf you accidently drop the LCD and you find it broken on the surface but the display still works. You might just break the touch panel; you can find a repair house or find a youtube video to replace the touch panel. If you find the display not showing, especially you find the fluid leaking out. You need to reply the whole display modules.

Dim LCD displayLCD can’t emit light itself. It uses backlight. Normally, the backlight is not fully driven, you can increase the LED backlight to make a dim LCD display brighter. But if you LCD display has been used for a long time, it is possible that the LED backlight has to be the end of life (not brightness enough) if you turn on 100% backlight brightness. In that case to fix LCD screen, you have to find a way to change the backlight. For some display, it is an easy job but it can be difficult for other displays depending on the manufacturing process.

LCD has white screen – If a LCD has a white screen which means the backlight is good. Simply check your signal input sources which are the most causes. It can also be caused by the display totally damaged by ESD or excess heat, shock which make the LCD controller broken or the connection failure which has to be repaired by professionals.

Blur ImagesAs the LCD images are made of RGB pixels, the screen shouldn’t be blur like old CRT displays. If you do see blur images, they might be caused by two reasons. 1) LCD has certain response time, if you are playing games or watch fast action movies, some old LCD displays can have image delays. 2) The surface of the LCD is made of a layer of plastic film with maximum hardness of 3H. If you clean the surface often or use the wrong detergent or solvent which cause the surface damage. To fix damage on LED screen it’s need to be changed with professionals.

If you have any questions about Orient Display displays and touch panels. Please feel free to contact: Sales Inquiries, Customer Service or Technical Support.

If your LCD television has ghosting, double images, dark on one side with slow refresh rates and symptoms similar to those shown in the pictures above there is a good chance we can fix it. You may find many Google sites and YouTube videos that show you how to "fix" this problem by applying pressure to the COF ribbons at the top of the LCD panel. That may work for a short time (or you may destroy the panel by trying to do it!) but in almost every case it will fail again in a month or two. It is sad that those posters never report back that the problem returned in such a short time. Tv Tech Electronics is part of a nationwide network of top technicians and through the combined efforts of that network we have developed a permanent repair for this problem. We have not had a single case where we performed this repair and the set came back again with the same problem. Sets smaller than 40 inches may not be repairable for this problem, but the larger sets often are. No other shop in the Kansas City area can repair this problem without replacing the panel at a cost that makes the repair uneconomical, give us a call at 816-756-0668 if your television displays this symptom.