sainsmart tft lcd mega shield v1.0 made in china

Arduino mega + 3.2" tft case. there are 2 different case bottoms, 1 without a hole and 1 with. both cases have a cutout for powering the Mega from a USB.

I designed this to dress up a project that used the SainSmart LCD Keypad Shield with and Arduino. The bezel itself prints pretty easily with very little support structure needed. The buttons are designed to be self-captivating (they just push in and...

I didn"t have a 3.5" TFT screen, but I did have the 3.2" ones (at the time the 3.5" were on backorder and I got impatient). This fits my 3.2" TFT perfectly. ... My unit comes from 4D Systems as well.

This top surface has 4 additional holes (for screwing to the bezel) and a square cut out of it to fit the LCD circuit board (see attached photo above) The bezel has 4 screw holes that line up with laser cut holes in the laser cut back plate. the...

Support piece for SainSmart kit: http://www.sainsmart.com/sainsmart-mega2560-board-3-5-tft-lcd-module-display-shield-kit-for-atmel-atmega-avr-16au-atmega8u2.html When both the shields are stacked, they are kind of flappy. This part fits on one end...

accurate CAD model of UPC "6013801500024" from the SainSmart Raspberry Pi 3 Model B Ultimate Kit with 5 inch LCD (Red&White Case)https://smile.amazon.com/gp/product/B01FHEBIE0/

A (very) compatible 800x480 LCD is available, but it"s 5 inch big and so the original bezel won"t fit. I also didn"t like the idea of sticking LCD to PCB by a piece of double sided tape. Here"s my original post about hacking it in:(pocket)CHIP with...

I bought a 4.3" TFT LCD Color Monitor off eBay for a reverse camera I installed in my car and had nothing to mount it to my car with. Monitor dimensions were 120mm(L) x 75mm(W) x 15mm(H) and this seemed to fit quite snugly. I have only created a...

This is a sipmple box/case for Arduino Uno and 2.4"" TFT Lcd Touch Screen. There are 2 kind of cases: closed or with open grooves for refrigeration. Originally made for a mini - meteo station, it can be customizable with FreeCad file. ...It was made...

A small mountable holder for a fasttech LCD module. Mounting pins are a little tight but can be snapped off if not needed. Mount holes are designed for assorted leg or spacer designs. Holes are 5mm dia, 34mm apart and hole centre 5.5mm from edge if...

I just redesigned it so it can house cheap chinese 2.4" TFT touchscreen, instead of hard to find and expensive 2.8". No support is needed for any of parts.

This is an update to the FreeTouchDeck case by Dustin Watts that holds a 3.2" TFT display since I bought a different size than Dustin used. I modified the Top_for_TFT_with_Headers.stl file. I"ve also uploaded the Fusion 360 file....

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

LCD screen bezel for Oneplus 2. If not only your screen is destroyed, but also the black plastic frame surrounding it (see picture), you can try your luck by printing this bezel and installing it. Replacement screens do not come with this bezel,...

The TFT display is a kind of LCD that is connected to each pixel using a transistor and it features low current consumption, high-quality, high-resolution and backlight. This 2.8-inch full color LCD has a narrow PCB display. The resolution is 320×280 pixels and it has a four-wire SPI interface and white backlight.