20x4 lcd display dimensions brands

STN Blue background with White Edge-lit backlight, bottom (or 6:00) viewing angle, Transmissive (negative), RoHS Compliant. Available in both 3V or 5V power supply options.This display has a wide temperature range: -20° Celcius to +70° Celcius which equates to (-4° Fahrenheit to +158° Fahrenheit).

STN (super twisted nematic) provides a sharper image and wider viewing angle than TN (Twisted Nematic). The cost for STN if approximately 5% higher than TN. STN is an ideal fluid for outdoor products that need to be read at various angles. The Transmissive polarizer is best used for displays that run with the backlight on all the time. This polarizer provides the brightest backlight possible. When you have a need for a bright backlight with lower power drain, transmissive is a good choice.

Focus LCDs can provide many accessories to go with your display. If you would like to source a connector, cable, test jig or other accessory preassembled to your LCD (or just included in the package), our team will make sure you get the items you need.Get in touch with a team member today to accessorize your display!

Focus Display Solutions (aka: Focus LCDs) offers the original purchaser who has purchased a product from the FocusLCDs.com a limited warranty that the product (including accessories in the product"s package) will be free from defects in material or workmanship.

A 20 x 4 character LCD display with white text on a vivid blue backlit LCD. The pictures don"t do justice to the bright blue background with clear white text of this display.

Adding to what N1VG posted, you can indeed control this module, or any other HD47780-based character LCD module for that matter, with six lines. If you"re using an Arduino as the brains for your project, the LiquidCrystal library that comes with the Arduino IDE will run a HD47780-based module from six pins without having to manage things like passing nybbles to the module - you can just include LiquidCrystal.h, declare a new object (e.g., LiquidCrystal lcd(2,3,4,5,6,7); to use pins 2-7 to control the module), and just shoot data to it with the print() and write() commands. The library will handle the rest.

You can get by with 6 I/O lines for an HD44780. Just keep the RW pin pulled low (assuming you don"t need to read from the display) and connect only the high 4 data lines. You"ll need to send it a command to put the bus into 4-bit mode, and of course you"ll have to write to it one nybble at a time, but that"s not hard to do.

Not sure if this is normal. My LCD, using the liquidcrystal library, wraps to the third line after finishing the first (then it goes to the second, then the fourth), but addressing each line is normal when using setCursor().

The "solution" I came up with was simply to use the cursor positioning feature to write to the lines I wanted. Since you"re writing strings anyway, it"s not terribly difficult to do. If you"re making a display for a project, just account for what ends up on what line.

Does anyone know where I can get a pre-manufactured ribbon cable assembly suitable for use with this LCD? Soldering a thru-hole connector or pin header to the panel is something that can probably be done in our shop, but assembling our own cables from scratch may be a bit beyond our ability to do routinely... We just need a 6" cable with (say) female sockets (16x1) at both ends... The other end to plug into a suitable header on an Arduino-based PCB... Thanks for any tips, -Mike

I made a tutorial (in portuguese) about how to use, create custom characters and design menus for the LCD display. Take a look: http://engenheirando.com/arduino/displaylcd/

Can anyone confirm if this works with an Arduino Uno? Following these directions (http://arduino.cc/en/Tutorial/LiquidCrystal), no matter what I do I can only see solid blocks on two of the 4 rows when the pot is turned all the way down. Is this because the Arduino library is for a 16x2 character LCD and this one is a 20x4?

I forgot to buy breakaway male header pins for this LCD module. However, I do have spare female headers from a previous project. Would I be able to use the female headers?

This display has a parallel interface, so it will require about 6 I/O pins to run. The parallel protocol is complex, but there are good LCD libraries out there which make it easy to use. The difference between this and a serial display is that the serial display will only require one I/O pin.

If you use straight headers, the clips used to anchor the lcd to the board get in the way when you try to plug it into a breadboard with power rails on the side.

A very useful LCD - and, if you need it to take even less than 6 pins, there"s a library (by Chris Parish) for using it with a 74HC595 shift register that reduces it to 3 digital output pins. The library and Chris"s tutorial is here - http :// cjparish.blogspot.com/2010/01/controlling-lcd-display-with-shift.html

@Twiddler: Yes, it"s possible to write too fast. Check the write cycle timings in the datasheet. The enable signal can"t be cycled faster than 2MHz. Also after each command sent to the LCD, you have to wait until the busy flag is clear, or delay several microseconds to milliseconds (depending on which command).

This 20-character, 4-line parallel liquid crystal display provides a large viewing area. It features white text on a blue background with an LED backlight and uses the common HD44780 interface, so sample interface code is widely available for a variety of microcontrollers. This display is electrically compatible with the LCD that is included as part of some of our Orangutan X2 robot controller packages, although the physical interface is different.

As shown in the diagram above, a potentiometer whose output is connected to Vo will allow you to set the contrast for optimal viewing of your display.

This LCD has an LED backlight. The voltage drop across the LEDs is typically about 3.2 V and the recommended current through the LEDs is 72 mA. This LCD includes a 25.5 Ω resistance (two 51 Ω resistors in parallel) in series with the backlight, so an external current-limiting resistor is not required for backlight supply voltages up to 5 V. For higher voltages, you should add a current-limiting resistor RLIMIT as shown above where:

Note: No cables or connectors are included with this product, but a straight or right angle male header can be purchased separately to be soldered into the through-holes. We also have 1×16-pin female headers and crimp connector housings to mate with the male headers. This LCD is intended for use with 5V systems.

LCD display of 20 characters x 4 rows that uses the HD44780 interface found on most parallel character displays. It has a white backlight with blue characters.

LCD display of 20 characters x 4 rows that uses the HD44780 interface found on most parallel character displays. It has a white backlight with blue characters.

The Displaytech 204G series is a lineup of 20x4 character LCD modules. These modules have a 98x60 mm outer dimension with 77x25.2 mm viewing area on the display. The 204G 20x4 LCD displays are available in STN or FSTN LCD modes with or without an LED backlight. The backlight color options include yellow green, white, blue, pure green, or amber color. Get a free quote direct from Displaytech for a 20x4 character LCD display from the 204G series.

Green/Yelow LED backlight. Alphanumeric dot matrix. 80 characters over 4 lines. Display area 76x26mm. Display bezel 98x40mm. 5V supply voltage. Arduino compatible. 99x60mm overall dimensions.

A 20x4 LCD display is very basic module and is very commonly used in various devices and circuits. These modules are preferred over seven segments and other multi segment LEDs. The reasons being: LCDs are economical; easily programmable; have no limitation of displaying special & even custom characters (unlike in seven segments), animations and so on.

A 20x4 LCD means it can display 20 characters per line and there are 4 such lines. In this LCD each character is displayed in 5x7 pixel matrix. This LCD has two registers, namely, Command and Data. This is standard HD44780 controller LCD.