tft display benefits quotation

IPS (In-Plane Switching) lcd is still a type of TFT LCD, IPS TFT is also called SFT LCD (supper fine tft ),different to regular tft in TN (Twisted Nematic) mode, theIPS LCD liquid crystal elements inside the tft lcd cell, they are arrayed in plane inside the lcd cell when power off, so the light can not transmit it via theIPS lcdwhen power off, When power on, the liquid crystal elements inside the IPS tft would switch in a small angle, then the light would go through the IPS lcd display, then the display on since light go through the IPS display, the switching angle is related to the input power, the switch angle is related to the input power value of IPS LCD, the more switch angle, the more light would transmit the IPS LCD, we call it negative display mode.

The regular tft lcd, it is a-si TN (Twisted Nematic) tft lcd, its liquid crystal elements are arrayed in vertical type, the light could transmit the regularTFT LCDwhen power off. When power on, the liquid crystal twist in some angle, then it block the light transmit the tft lcd, then make the display elements display on by this way, the liquid crystal twist angle is also related to the input power, the more twist angle, the more light would be blocked by the tft lcd, it is tft lcd working mode.

A TFT lcd display is vivid and colorful than a common monochrome lcd display. TFT refreshes more quickly response than a monochrome LCD display and shows motion more smoothly. TFT displays use more electricity in driving than monochrome LCD screens, so they not only cost more in the first place, but they are also more expensive to drive tft lcd screen.The two most common types of TFT LCDs are IPS and TN displays.

Because every point on the TFT LCD screen maintains that color and brightness after receiving the signal, it glows at a constant rate, rather than constantly refreshing the bright spots as the cathode ray tube display (CRT) does. As a result, the TFT LCD is of high quality and does not flicker, reducing eye fatigue to a very low level.

For displays of the same size, the visual area of the TFT LCD screen is larger. The visible area of the TFT LCD is the same as its diagonal size. Cathode ray tube display screen picture tube front panel around an inch or so of the border can not be used for display.

The original LCD screen is usually used in electronic watches and calculators because it is unable to display delicate characters. With the continuous development and progress of liquid crystal display technology, character display begins to be exquisite, but also supports the basic color display, and gradually used in liquid crystal TV, camera liquid crystal display.

The subsequent DSTN and TFT were widely made into liquid crystal display devices in computers, and DSTN LCD screens were used in early notebooks. TFT is used not only on laptops (most laptops now use TFT displays), but also on mainstream desktop displays.

The display material of the traditional display screen is phosphor, which is shown by the impact of the electron beam on the phosphor. The electron beam produces strong electromagnetic radiation in the moment it hits the phosphor. Although there are many display products in dealing with the radiation problem more effectively, as far as possible to reduce the amount of radiation to a very low, but to completely eliminate it is difficult. Relatively speaking, the TFT LCD screen has an innate advantage in preventing radiation because it does not exist at all.

In the aspect of electromagnetic wave prevention, TFT LCD screen also has its own unique advantages. It uses strict sealing technology to seal a small number of electromagnetic waves from the driving circuit in the display, while ordinary displays in order to emit heat. The internal circuit must be in contact with the air as much as possible so that the electromagnetic waves generated by the internal circuit "leak" outward in large quantities.

TFT LCD screens are digital and do not use analog interfaces like cathode ray tube color displays. In other words, with the TFT LCD, the graphics card no longer needs to convert the digital signal into an analog signal and output it as usual. In theory, this would make the color more accurate and perfect.

A traditional cathode ray tube display is always dragged behind a bulky ray tube. The TFT LCD breaks through this limit and gives a whole new feel. The traditional display screen emits electron beam to the screen, so the neck of the picture tube can not be very short, when the screen increases, it is necessary to increase the size of the whole display.

On the other hand, the TFT LCD screen controls the liquid crystal molecular state through the electrode on the display screen to achieve the display purpose. Even if the screen is enlarged, its volume will not increase in direct proportion, and its weight is much lighter than the traditional display with the same display area.

Compared with the traditional display screen, the TFT LCD screen starts with a pure flat glass panel, and its display effect is flat at right angles, giving people a refreshing feeling. And it is easier for LCD to achieve high resolution on a small screen. For example, a 17-inch LCD can achieve a good resolution of 1280 × 1024. On the other hand, the effect of using a resolution of more than 1280 × 1024 on an 18-inch CRT color display is not entirely satisfactory.

The traditional display screen is composed of many circuits. When these circuits drive the cathode ray picture tube, they need to consume a lot of power, and with the continuous increase of the volume, the power consumed by the internal circuit will certainly increase. In contrast, the power consumption of TFT LCD is mainly consumed by its internal electrode and driver IC, so the power consumption is much smaller than that of traditional display.

TFT Liquid crystal display products are diversified, convenient and versatile, simple to keep up, upgrade, update, long service life, and have many alternative characteristics.

The display range covers the appliance range of all displays from one to forty inches and, therefore, the giant projection plane could be a large display terminal.

Display quality from the most straightforward monochrome character graphics to high resolution, high colour fidelity, high brightness, high contrast, the high response speed of various specifications of the video display models.

In particular, the emergence of TFT LCD electronic books and periodicals will bring humans into the era of paperless offices and paperless printing, triggering a revolution in the civilized way of human learning, dissemination, and recording.

It can be generally used in the temperature range from -20℃ to +50℃, and the temperature-hardened TFT LCD can operate at low temperatures up to -80 ℃. It can be used as a mobile terminal display or desktop terminal display and can be used as a large screen projection TV, which is a full-size video display terminal with excellent performance.

The manufacturing technology has a high degree of automation and sound characteristics of large-scale industrial production. TFT LCD industry technology is mature, with a more than 90% mass production rate.

From the beginning of flat glass plates, its display effect is flat right angles, letting a person have a refreshing feeling. LCDs are simple to achieve high resolution on small screens.

TFT stands for thin-film transistor, which means that each pixel in the device has a thin-film transistor attached to it. Transistors are activated by electrical currents that make contact with the pixels to produce impeccable image quality on the screen. Here are some important features of TFT displays.Excellent Colour Display.Top notch colour contrast, clarity, and brightness settings that can be adjusted to accommodate specific application requirements.Extended Half-Life.TFT displays boast a much higher half-life than their LED counterparts and they also come in a variety of size configurations that can impact the device’s half-life depending on usage and other factors.TFT displays can have either resistive or capacitive touch panels.Resistive is usually the standard because it comes at a lower price point, but you can also opt for capacitive which is compatible with most modern smartphones and other devices.TFT displays offer exceptional aspect ratio control.Aspect ratio control contributes to better image clarity and quality by mapping out the number of pixels that are in the source image compared to the resolution pixels on the screen.Monitor ghosting doesn’t occur on TFT displays.This is when a moving image or object has blurry pixels following it across the screen, resembling a ghost.

TFT displays are incredibly versatile.The offer a number of different interface options that are compatible with various devices and accommodate the technical capabilities of all users.

There are two main types of TFT LCD displays:· Twisted nematic TFT LCDs are an older model. They have limited colour options and use 6 bits per each blue, red, and green channel.

In-plane switching TFT LCDs are a newer model. Originally introduced in the 1990s by Hitachi, in-plane switching TFT LCDs consist of moving liquid pixels that move in contrast or opposite the plane of the display, rather than alongside it.

The type of TFT LCD monitor or industrial display you choose to purchase will depend on the specifications of your application or project. Here are a few important factors to consider when selecting an appropriate TFT LCD display technology:Life expectancy/battery life.Depending on the length of ongoing use and the duration of your project, you’re going to want to choose a device that can last a long time while maintaining quality usage.

Image clarity.Some TFT displays feature infrared touchscreens, while others are layered. The former is preferable, especially in poor lighting conditions or for outdoor and industrial applications, because there’s no overlay and therefore no obstructions to light emittance.

The environmental conditions make a difference in operation and image clarity. When choosing a TFT for outdoor or industrial applications, be sure to choose one that can withstand various environmental elements like dust, wind, moisture, dirt, and even sunlight.

As a leading manufacturer and distributor of high-quality digital displays in North America, Nauticomp Inc. can provide custom TFT LCD monitor solutions that are suitable for a multitude of industrial and commercial indoor and outdoor applications. Contact us today to learn more.

A thin-film-transistor liquid-crystal display (TFT LCD) is a variant of a liquid-crystal display that uses thin-film-transistor technologyactive matrix LCD, in contrast to passive matrix LCDs or simple, direct-driven (i.e. with segments directly connected to electronics outside the LCD) LCDs with a few segments.

In February 1957, John Wallmark of RCA filed a patent for a thin film MOSFET. Paul K. Weimer, also of RCA implemented Wallmark"s ideas and developed the thin-film transistor (TFT) in 1962, a type of MOSFET distinct from the standard bulk MOSFET. It was made with thin films of cadmium selenide and cadmium sulfide. The idea of a TFT-based liquid-crystal display (LCD) was conceived by Bernard Lechner of RCA Laboratories in 1968. In 1971, Lechner, F. J. Marlowe, E. O. Nester and J. Tults demonstrated a 2-by-18 matrix display driven by a hybrid circuit using the dynamic scattering mode of LCDs.T. Peter Brody, J. A. Asars and G. D. Dixon at Westinghouse Research Laboratories developed a CdSe (cadmium selenide) TFT, which they used to demonstrate the first CdSe thin-film-transistor liquid-crystal display (TFT LCD).active-matrix liquid-crystal display (AM LCD) using CdSe TFTs in 1974, and then Brody coined the term "active matrix" in 1975.high-resolution and high-quality electronic visual display devices use TFT-based active matrix displays.

The liquid crystal displays used in calculators and other devices with similarly simple displays have direct-driven image elements, and therefore a voltage can be easily applied across just one segment of these types of displays without interfering with the other segments. This would be impractical for a large display, because it would have a large number of (color) picture elements (pixels), and thus it would require millions of connections, both top and bottom for each one of the three colors (red, green and blue) of every pixel. To avoid this issue, the pixels are addressed in rows and columns, reducing the connection count from millions down to thousands. The column and row wires attach to transistor switches, one for each pixel. The one-way current passing characteristic of the transistor prevents the charge that is being applied to each pixel from being drained between refreshes to a display"s image. Each pixel is a small capacitor with a layer of insulating liquid crystal sandwiched between transparent conductive ITO layers.

The circuit layout process of a TFT-LCD is very similar to that of semiconductor products. However, rather than fabricating the transistors from silicon, that is formed into a crystalline silicon wafer, they are made from a thin film of amorphous silicon that is deposited on a glass panel. The silicon layer for TFT-LCDs is typically deposited using the PECVD process.

Polycrystalline silicon is sometimes used in displays requiring higher TFT performance. Examples include small high-resolution displays such as those found in projectors or viewfinders. Amorphous silicon-based TFTs are by far the most common, due to their lower production cost, whereas polycrystalline silicon TFTs are more costly and much more difficult to produce.

The twisted nematic display is one of the oldest and frequently cheapest kind of LCD display technologies available. TN displays benefit from fast pixel response times and less smearing than other LCD display technology, but suffer from poor color reproduction and limited viewing angles, especially in the vertical direction. Colors will shift, potentially to the point of completely inverting, when viewed at an angle that is not perpendicular to the display. Modern, high end consumer products have developed methods to overcome the technology"s shortcomings, such as RTC (Response Time Compensation / Overdrive) technologies. Modern TN displays can look significantly better than older TN displays from decades earlier, but overall TN has inferior viewing angles and poor color in comparison to other technology.

Most TN panels can represent colors using only six bits per RGB channel, or 18 bit in total, and are unable to display the 16.7 million color shades (24-bit truecolor) that are available using 24-bit color. Instead, these panels display interpolated 24-bit color using a dithering method that combines adjacent pixels to simulate the desired shade. They can also use a form of temporal dithering called Frame Rate Control (FRC), which cycles between different shades with each new frame to simulate an intermediate shade. Such 18 bit panels with dithering are sometimes advertised as having "16.2 million colors". These color simulation methods are noticeable to many people and highly bothersome to some.gamut (often referred to as a percentage of the NTSC 1953 color gamut) are also due to backlighting technology. It is not uncommon for older displays to range from 10% to 26% of the NTSC color gamut, whereas other kind of displays, utilizing more complicated CCFL or LED phosphor formulations or RGB LED backlights, may extend past 100% of the NTSC color gamut, a difference quite perceivable by the human eye.

IPS has since been superseded by S-IPS (Super-IPS, Hitachi Ltd. in 1998), which has all the benefits of IPS technology with the addition of improved pixel refresh timing.

In 2004, Hydis Technologies Co., Ltd licensed its AFFS patent to Japan"s Hitachi Displays. Hitachi is using AFFS to manufacture high end panels in their product line. In 2006, Hydis also licensed its AFFS to Sanyo Epson Imaging Devices Corporation.

A technology developed by Samsung is Super PLS, which bears similarities to IPS panels, has wider viewing angles, better image quality, increased brightness, and lower production costs. PLS technology debuted in the PC display market with the release of the Samsung S27A850 and S24A850 monitors in September 2011.

TFT dual-transistor pixel or cell technology is a reflective-display technology for use in very-low-power-consumption applications such as electronic shelf labels (ESL), digital watches, or metering. DTP involves adding a secondary transistor gate in the single TFT cell to maintain the display of a pixel during a period of 1s without loss of image or without degrading the TFT transistors over time. By slowing the refresh rate of the standard frequency from 60 Hz to 1 Hz, DTP claims to increase the power efficiency by multiple orders of magnitude.

Due to the very high cost of building TFT factories, there are few major OEM panel vendors for large display panels. The glass panel suppliers are as follows:

External consumer display devices like a TFT LCD feature one or more analog VGA, DVI, HDMI, or DisplayPort interface, with many featuring a selection of these interfaces. Inside external display devices there is a controller board that will convert the video signal using color mapping and image scaling usually employing the discrete cosine transform (DCT) in order to convert any video source like CVBS, VGA, DVI, HDMI, etc. into digital RGB at the native resolution of the display panel. In a laptop the graphics chip will directly produce a signal suitable for connection to the built-in TFT display. A control mechanism for the backlight is usually included on the same controller board.

The low level interface of STN, DSTN, or TFT display panels use either single ended TTL 5 V signal for older displays or TTL 3.3 V for slightly newer displays that transmits the pixel clock, horizontal sync, vertical sync, digital red, digital green, digital blue in parallel. Some models (for example the AT070TN92) also feature input/display enable, horizontal scan direction and vertical scan direction signals.

New and large (>15") TFT displays often use LVDS signaling that transmits the same contents as the parallel interface (Hsync, Vsync, RGB) but will put control and RGB bits into a number of serial transmission lines synchronized to a clock whose rate is equal to the pixel rate. LVDS transmits seven bits per clock per data line, with six bits being data and one bit used to signal if the other six bits need to be inverted in order to maintain DC balance. Low-cost TFT displays often have three data lines and therefore only directly support 18 bits per pixel. Upscale displays have four or five data lines to support 24 bits per pixel (truecolor) or 30 bits per pixel respectively. Panel manufacturers are slowly replacing LVDS with Internal DisplayPort and Embedded DisplayPort, which allow sixfold reduction of the number of differential pairs.

The bare display panel will only accept a digital video signal at the resolution determined by the panel pixel matrix designed at manufacture. Some screen panels will ignore the LSB bits of the color information to present a consistent interface (8 bit -> 6 bit/color x3).

With analogue signals like VGA, the display controller also needs to perform a high speed analog to digital conversion. With digital input signals like DVI or HDMI some simple reordering of the bits is needed before feeding it to the rescaler if the input resolution doesn"t match the display panel resolution.

Kawamoto, H. (2012). "The Inventors of TFT Active-Matrix LCD Receive the 2011 IEEE Nishizawa Medal". Journal of Display Technology. 8 (1): 3–4. Bibcode:2012JDisT...8....3K. doi:10.1109/JDT.2011.2177740. ISSN 1551-319X.

Brody, T. Peter; Asars, J. A.; Dixon, G. D. (November 1973). "A 6 × 6 inch 20 lines-per-inch liquid-crystal display panel". 20 (11): 995–1001. Bibcode:1973ITED...20..995B. doi:10.1109/T-ED.1973.17780. ISSN 0018-9383.

K. H. Lee; H. Y. Kim; K. H. Park; S. J. Jang; I. C. Park & J. Y. Lee (June 2006). "A Novel Outdoor Readability of Portable TFT-LCD with AFFS Technology". SID Symposium Digest of Technical Papers. AIP. 37 (1): 1079–82. doi:10.1889/1.2433159. S2CID 129569963.

Kim, Sae-Bom; Kim, Woong-Ki; Chounlamany, Vanseng; Seo, Jaehwan; Yoo, Jisu; Jo, Hun-Je; Jung, Jinho (15 August 2012). "Identification of multi-level toxicity of liquid crystal display wastewater toward Daphnia magna and Moina macrocopa". Journal of Hazardous Materials. Seoul, Korea; Laos, Lao. 227–228: 327–333. doi:10.1016/j.jhazmat.2012.05.059. PMID 22677053.

IPS, also known as In-Plane Switching, is a type of monitor display and screen technology that uses a voltage to control the alignment of liquid crystals, similar to TN technology. However, IPS displays use a different crystal orientation where the crystals are parallel to the glass substrates, hence the term ‘in-plane’. Rather than ‘twisting’ the crystals to modify the amount of light let through, IPS crystals are essentially rotated, which has a range of benefits. IPS displays offer the best color reproduction as well as the widest viewing angles compared to other LCD technologies.

While TN LCD’s support high refresh rates with low response times, they do come with sub-optimal viewing angles, and slightly diminished color reproduction. IPS panels address these downfalls with 80 degree viewing angles that eliminate color inversion and contrast diminishment. IPS technology is ideal for a wide array of applications such as medical, industrial, HVAC, Pool/Spa due to the ability to use the displays in both landscape and portrait mode while maintaining uniform viewing angles. This also allows for displays to be seen from different angles and heights, ideal for jacuzzi controls and thermostats that tend to require consideration of dynamic user parameters.

Dr Pan: Hello, Greg. TFT LCD module is one of the best LCD technology. We can simply consider it as TFT+LCD+LED backlight, and monochrome LCD module consists of LCD+LED backlight. An image on an LCD we can see is composed of pixels. TFT is the abbreviation for thin film transistor and it controls the R, G, B colors of each pixel respectively on the surface of LCD.

TFT LCD is a high standard product and it is not well customized as monochrome LCD. But still, it has a variety of options to meet the customers’ requirements.The sizes range from 1.44 inch to 130.0 inch;

Display size, contrast, color, brightness, resolution, and power are key factors in choosing the right display technology for your application. However, making the right choice in how you feed the information to the display is just as vital, and there are many interface options available.

All displays work in a similar manner. In a very basic explanation, they all have many rows and columns of pixels driven by a controller that communicates with each pixel to emit the brightness and color needed to make up the transmitted image. In some devices, the pixels are diodes that light up when current flows (PMOLEDs and AMOLEDs), and in other electronics, the pixel acts as a shutter to let some of the light from a backlight visible. In all cases, a memory array stores the image information that travels to the display through an interface.

According to Wikipedia, "an interface is a shared boundary across which two separate components of a computer system exchange information. The exchange can be between software, computer hardware, peripheral devices, humans, and combinations of these. Some computer hardware devices such as a touchscreen can both send and receive data through the interface, while others such as a mouse or microphone may only provide an interface to send data to a given system.” In other words, an interface is something that facilitates communication between two objects. Although display interfaces serve a similar purpose, how that communication occurs varies widely.

Serial Peripheral Interface (SPI) is a synchronous serial communication interface best-suited for short distances. It was developed by Motorola for components to share data such as flash memory, sensors, Real-Time Clocks, analog-to-digital converters, and more. Because there is no protocol overhead, the transmission runs at relatively high speeds. SPI runs on one master (the side that generates the clock) with one or more slaves, usually the devices outside the central processor. One drawback of SPI is the number of pins required between devices. Each slave added to the master/slave system needs an additional chip select I/O pin on the master. SPI is a great option for small, low-resolution displays including PMOLEDs and smaller LCDs.

Philips Semiconductors invented I2C (Inter-integrated Circuit) or I-squared-C in 1982. It utilizes a multi-master, multi-slave, single-ended, serial computer bus system. Engineers developed I2C for simple peripherals on PCs, like keyboards and mice to then later apply it to displays. Like SPI, it only works for short distances within a device and uses an asynchronous serial port. What sets I2C apart from SPI is that it can support up to 1008 slaves and only requires two wires, serial clock (SCL), and serial data (SDA). Like SPI, I2C also works well with PMOLEDs and smaller LCDs. Many display systems transfer the touch sensor data through I2C.

RGB is used to interface with large color displays. It sends 8 bits of data for each of the three colors, Red Green, and Blue every clock cycle. Since there are 24 bits of data transmitted every clock cycle, at clock rates up to 50 MHz, this interface can drive much larger displays at video frame rates of 60Hz and up.

Low-Voltage Differential Signaling (LVDS) was developed in 1994 and is a popular choice for large LCDs and peripherals in need of high bandwidth, like high-definition graphics and fast frame rates. It is a great solution because of its high speed of data transmission while using low voltage. Two wires carry the signal,  with one wire carrying the exact inverse of its companion. The electric field generated by one wire is neatly concealed by the other, creating much less interference to nearby wireless systems. At the receiver end, a circuit reads the difference (hence the "differential" in the name) in voltage between the wires. As a result, this scheme doesn’t generate noise or gets its signals scrambled by external noise. The interface consists of four, six, or eight pairs of wires, plus a pair carrying the clock and some ground wires. 24-bit color information at the transmitter end is converted to serial information, transmitted quickly over these pairs of cables, then converted back to 24-bit parallel in the receiver, resulting in an interface that is very fast to handle large displays and is very immune to interference.

Mobile Industry Processor Interface (MIPI) is a newer technology that is managed by the MIPI Alliance and has become a popular choice among wearable and mobile developers. MIPI uses similar differential signaling to LVDS by using a clock pair and one to eight pairs of data called lanes. MIPI supports a complex protocol that allows high speed and low power modes, as well as the ability to read data back from the display at lower rates. There are several versions of MIPI for different applications, MIPI DSI being the one for displays.

Display components stretch the limitations of bandwidth. For perspective, the most common internet bandwidth in a residential home runs on average at around 20 megabits per second or 20 billion 1s and 0s per second. Even small displays can require 4MB per second, which is a lot of data in what is often a tightly constrained physical space.

Take the same PMOLED display with the 128 x 128 resolution and 16,384 separate diodes; it requires information as to when and how brightly to illuminate each pixel. For a display with only 16 shades, it takes 4 bits of data. 128 x 128 x 4 = 65,536 bits for one frame. Now multiply it by the 60Hz, and you get a bandwidth of 4 megabits/second for a small monochrome display.

A TN or Twisted Nematic TFT LCD is a cost-effective high performance LCD. It offers good brightness performance and fast response times. However, it suffers in one key area and that is its viewing cone. TN LCD’s typically have three good viewing angle directions. In these directions the image is typically clear and colors are consistent up to 80 degrees from the center of the LCD. The remaining viewing direction is usually good through 40-50 degrees from center. Afterwards, the image is likely to invert, almost appearing like an x-ray.

The worlds of high-end Color LCD Modules are taken over. As our world evolved and embedded devices becoming more, and more sophisticated and prevalent, we tend to look at the art of design. Steve Jobs sums it up just right. “Design is not just what it looks like and feels like. Design is how it works.” TFT LCD modules are a type of variant of an LCD which uses thin film, appliances such as: TV, computer monitors, kindles, mobile phone, and navigation system. The construction of a color LCD module or TFT LCD is quite extraordinary because of the circuit layout process; this form of layout is similar to the layout of a semiconductor product. Even though as we observe the TFT LCD display we came across few pros and cons which are most needed for this discussion. The advantages of TFT LCD are as follows: less energy consumption, visibility is sharper in other words has superb quality, physical design, response time, and less eye strain etc… With every great product there are few disadvantages associated, such as, cost and viewing angles.

TFT LCD displays are very convenient because of the energy consumption associate with this display, knowingly in today’s society saving energy is a number one priority to reduce greenhouse gas and ensure a better future generations. Due to the construction of TFT structures Pixel like materials does not consume much energy to begin with except this material consume far less power than a comparable CRT monitor. The images of a TFT display does not rely on the scanning of electron beams instead they are free from flicker and has a crisp image, with no geometric distortion. The physical design of TFT display are space savors which can be position anywhere in ones office, or house with a rotations mechanism in place for less constrains on space.

As mention before TFT LCD has few disadvantages, due to the nature of the design TFT LCD display may cost a little more than a regular monochrome display. Other disadvantages may arise when the viewing the display at the 6 0’clock direction but in fact the optimal viewing is at the 12’oclock direction this may also lead to inversion which or common in situation like this; however TFT displays are superior and will be in production for years to come.

LCD stands for “Liquid Crystal Display” and TFT stands for “Thin Film Transistor”. These two terms are used commonly in the industry but refer to the same technology and are really interchangeable when talking about certain technology screens. The TFT terminology is often used more when describing desktop displays, whereas LCD is more commonly used when describing TV sets. Don’t be confused by the different names as ultimately they are one and the same. You may also see reference to “LED displays” but the term is used incorrectly in many cases. The LED name refers only to the backlight technology used, which ultimately still sits behind an liquid crystal panel (LCD/TFT).

As TFT screens are measured differently to older CRT monitors, the quoted screen size is actually the full viewable size of the screen. This is measured diagonally from corner to corner. TFT displays are available in a wide range of sizes and aspect ratios now. More information about the common sizes of TFT screens available can be seen in our section about resolution.

The aspect ratio of a TFT describes the ratio of the image in terms of its size. The aspect ratio can be determined by considering the ratio between horizontal and vertical resolution.

16:9 = wide screen formats such as 1920 x 1080 and 2560 x 1440. 16:9 is commonly used for multimedia displays and TV’s and is increasingly becoming the standard

The resolution of a TFT is an important thing to consider. All TFT’s have a certain number of pixels making up their liquid crystal matrix, and so each TFT has a “native resolution” which matches this number. It is always advisable to run the TFT at its native resolution as this is what it is designed to run at and the image does not need to be stretched or interpolated across the pixels. This helps keep the image at its most clear and at optimum sharpness. Some screens are better than others at running below the native resolution and interpolating the image which can sometimes be useful in games.

You generally cannot run a TFT at a resolution of above its native resolution although some screens have started to offer “Virtual” resolutions, for example “virtual 4k” where the screen will accept a 3840 x 2160 input from your graphics card but scale it back to match the native resolution of the panel which is often 2560 x 1440 in these examples. This whole process is rather pointless though as you lose a massive amount of image quality in doing so.

Ultra-high resolutions must be thought of in a slightly different way. Ultra HD (3840 x 2160) and 4K (4096 x 2160) resolutions are being provided nowadays on standard screen sizes like 24 – 27” for instance. Traditionally as you increased the resolution of panels it was about providing more desktop real estate to work with. However, with those resolutions being so high, and the screen size being relatively small still, the image and text becomes incredibly small if you run the screen at normal scaling at those native resolutions. For instance imagine a 3840 x 2160 resolution on a 24” screen compared with 1920 x 1080. The latter would probably be considered a comfortable font size for most users. These ultra-high resolutions nowadays are about improving image clarity and sharpness, and providing a higher pixel density (measured as pixels per inch = PPI). In doing so, you can improve the sharpness and clarity of an image much like Apple have famously done with their “Retina” displays on iPads and iPhones. To avoid complications with tiny images and fonts, you will then need to enable scaling in your operating system to make everything easier to see. For instance if you enabled scaling at 150% on a 3840 x 2160 resolution, you would end up with a screen real estate equivalent to a 2560 x 1440 panel (3840 / 1.5 = 2560 and 2160 / 1.5 = 1440). This makes text much easier to read and the whole image a more comfortable size, but you then get additional benefits from the higher pixel density instead, which results in a sharper and crisper image.

Generally you will need to take scaling in to consideration when purchasing any ultra-high resolution screen, unless it’s of a very large size. The scaling ability does vary however between different operating systems so be careful. Apple OS and modern Windows (8 and 10) are generally very good at handling scaling for ultra-high res displays. Older operating systems are less capable and may sometimes be complicated. You will also find varying support from different applications and games, and often end up with weird sized fonts or sections that are not scaled up and remain extremely small. A “standard” resolution where you don’t need to worry about scaling might be simpler for most users.

To display this content of this type, your screen needs to be able to 1) handle the full resolution naturally within its native resolution, and 2) be able to handle either the progressive scan or interlaced signal over whatever video interface you are using. If the screen cannot support the full resolution, the image can still be shown but it will be scaled down by the hardware and you won’t be take full advantage of the high resolution content. So for a monitor, if you want to watch 1080 HD content you will need a monitor which can support at least a vertical resolution of 1080 pixels, e.g. a 1920 x 1080 monitor.

Unlike on CRT’s where the dot pitch is related to the sharpness of the image, the pixel pitch of a TFT is related to the distance between pixels. This value is fixed and is determined by the size of the screen and the native resolution (number of pixels) offered by the panel. Pixel pitch is normally listed in the manufacturers specification. Generally you need to consider that the ‘tighter’ the pixel pitch, the smaller the text will be, and potentially the sharper the image will be. To be honest, monitors are normally produced with a sensible resolution for their size and so even the largest pixel pitches return a sharp images and a reasonable text size. Some people do still prefer the larger-resolution-crammed-into-smaller-screen option though, giving a smaller pixel pitch and smaller text. It’s down to choice and ultimately eye-sight.

For instance you might see a 35″ ultra-wide screen with only a 2560 x 1080 resolution which would have a 0.3200 mm pixel pitch. Compare this to a 25″ screen with 2560 x 1400 resolution and 0.2162 mm pixel pitch and you can see there will be a significant different in font size and image sharpness. There are further considerations when it comes to the pixel pitch of ultra-high resolution displays like Ultra HD and 4K. See the section on PPI for more information.

Instead manufacturers are now focusing on delivering higher resolutions in to existing panel sizes, not for the purpose of providing more desktop real-estate, but for the purpose of improving image sharpness and picture quality. Apple started this trend with their “Retina Displays” used in iPads and iPhones, improving image sharpness and clarity massively. It is common now to see smaller screens such as 24″ and 27″ for instance, but with high resolutions like 3840 x 2160 (Ultra HD) or even 5120 x 2880 (5K). By packing more pixels in to the same screen size which would typically offer a 2560 x 1440 resolution, panel manufacturers are able to provide much smaller pixel pitches and improve picture sharpness and clarity. To measure this new way of looking at resolution you will commonly see the spec of ‘Pixels Per Inch’ (PPI) being used.

Of course the problem with this is that if you run a screen as small as 27″ with a 5K resolution, the font size is absolutely tiny by default. You get a massive boost of desktop real-estate, just like when moving from 1920 x 1080 to 2560 x 1440, but that’s not the purpose of these higher resolutions now. To overcome this you need to use the scaling options in your Operating System software to scale the image and make it more usable. Windows provides for instance scaling options like 125% and 150% within the control panel. On a 3840 x 2160 Ultra HD resolution if you use a 150% scaling option for example you will in effect reduce the desktop area by a third, resulting in the same desktop area as a 2560 x 1440 display (i.e. 2560 x 150% = 3840). The OS scaling makes font sizes more comfortable and reasonable, but you maintain the sharp picture quality and small pixel pitch of the higher resolution panel. A 3840 x 2160 res panel scaled at 150% in Windows will look sharper and crisper than a 2560 x 1440 native panel without scaling, despite the fact both would have the same effective desktop area available.

While this aspect is not always discussed by display manufacturers it is a very important area to consider when selecting a TFT monitor. The LCD panels producing the image are manufactured by many different panel vendors and most importantly, the technology of those panels varies. Different panel technologies will offer different performance characteristics which you need to be aware of. Their implementation is dependent on the panel size mostly as they vary in production costs and in target markets. The four main types of panel technology used in the desktop monitor market are:

IPS was originally introduced to try and improve on some of the drawbacks of TN Film. While initially viewing angles were improved, the panel technology was traditionally fairly poor when it came to response times and contrast ratios. Production costs were eventually reduced and the main investor in this technology has been LG.Display (formerly LG.Philips). The original IPS panels were developed into the so-called Super IPS (S-IPS) generation and started to be more widely used in mainstream displays. These were characterized by their good colour reproduction qualities, 8-bit colour depth (without the need for Frame Rate Control) and very wide viewing angles. These panels were traditionally still quite slow when it came to pixel response times however and contrast ratios were mediocre. In more recent years a change was made to the pixel alignment in these IPS panels (see our detailed panel technology article for more information) which gave rise to the so-called Horizontal-IPS (H-IPS) classification. With the introduction of overdrive technologies, response times were improved significantly, finally making IPS a viable choice for gaming. This has resulted more recently in IPS panels being often regarded as the best all-round technology and a popular choice for display manufacturers in today’s market. Improvements in energy consumption and reduced production costs lead to the generation of so-called e-IPS panels. Unlike normal 8-bit S-IPS and H-IPS classification panels, the e-IPS generation worked with a 6-bit + FRC colour depth. Developments and improvements with colour depths also gave rise to a generation of “10-bit” panels with some manufacturers inventing new names for the panels they were using, including the co-called Performance-IPS (p-IPS). It is important to understand that these different variants are ultimately very similar and the names are often interchanged by different display vendors. For more information, see our detailed panel technologies guide.

Nowadays IPS panels are produced and developed by several leading panel manufacturers. LG.Display technically own the IPS name and continue to invest in this popular technology. Samsung began production of their very similar PLS (Plane to Line Switching) technology, as did AU Optronics with their AHVA (Advanced Hyper Viewing Angle). These are all so similar in performance and features that they can be simply referred to now as “IPS-type”. Indeed monitor manufacturers will normally stick to the common IPS name but the underlying panel may be produced by any number of different manufacturers investing in this type of panel tech. AU Optronics have done a good job with finally increasing the refresh rate of their IPS panels, and making them a more viable option for gamers. Native 144Hz IPS-type panels are now available and response times continue to be reduced as well. Modern IPS panels are characterized by decent response times, if not quite as fast as TN Film they are certainly more fluid than older panels. Contrast ratios are typically around 1000:1 and viewing angles continue to be the widest and most stable of any panel technology. You will find varying colour depths including 6-bit+FRC and 8-bit commonly being used, although this makes little difference in practice. One of the remaining limitations with IPS-type technologies are the so-called “IPS glow”, where darker content introduces a pale glow when viewed from an angle. It’s a characteristic of the panel technology and pretty hard to avoid without additional filters being added to the panels. On larger and wider screens some people find this glow distracting and problematic.

This technology was developed by Sharp for use in some of their TFT displays. It consists of several improvements that Sharp claim to have made, mainly to counter the drawbacks of the popular TN Film technology. They have introduced an Anti-Glare / Anti-Reflection (AGAR) screen coating which forms a quarter-wavelength filter. Incident light is reflected back from front and rear surfaces 180° out of phase, thus canceling reflection rather diffusing it as others do. As well as reducing glare and reflection from the screen, this is marketed as being able to offer deeper black levels. Sharp also claim to offer better contrast ratios than any competing technology (VA and IPS); but with more emphasis on improving these other technologies, this is probably not the case with more modern panels. There are very few ASV monitors around really, with the majority of the market being dominated by TN, VA and IPS panels.

This technology was developed by BOE Hydis, and is not really very widely used in the desktop TFT market, more in the mobile and tablet sectors. It is worth mentioning however in case you come across displays using this technology. It was developed by BOE Hydis to offer improved brightness and viewing angles to their display panels and claims to be able to offer a full 180/180 viewing angle field as well as improved colours. This is basically just an advancements from IPS and is still based on In Plane technology. They claim to “modify pixels” to improve response times and viewing angles thanks to improved alignment. They have also optimised the use of the electrode surface (fringe field effect), removed shadowed areas between pixels, horizontally aligned electric fields and replaced metal electrodes with transparent ones. More information about AFFS can be found here.

This panel technology was developed by NEC LCD, and is reported to offer wide viewing angles, fast response times, high luminance, wide colour gamut and high definition resolutions. Of course, there is a lot of marketing speak in there, and the technology is not widely employed in the mainstream monitor market. Wide viewing angles are possible thanks to the horizontal alignment of liquid crystals when electrically charged. This alignment also helps keep response times low, particularly in grey to grey transitions. Their SFT range also offers high definition resolutions and are commonly used in medical displays where extra fine detail is required.

One thing to note regarding pixel response time is that the overall performance of the TFT will also depend on the technology of the panel used. TN film panels offer response time graphs similar to that above, but screens based on traditional VA / IPSvariant panels can show response time graphs more like this (we are assuming for now non-overdriven panels):

Some reviews sites including TFTCentral have access to advanced photosensor (photodiodе + low-noise operational amplifier) and oscilloscope measurement equipment which allows them to measure response time as detailed above. See our article about response times for more information on that method. Graphs showing response time according to their equipment are produced. Other sites rely on observed responsiveness to compare how well a panel can perform in practice and what a user might see in normal use. We think it is important to study both methods if possible to give a fuller picture of a panels performance. For visual tests TFTCentral uses a program called PixPerAn (developed by Prad.de) which is good for comparing monitor responsiveness with its series of tests. The favourite seems to be the moving car test as shown here:

In addition to pixel response time measurements and visual tests described above, it is also possible to capture the levels of blurring and smearing the human eye will experience on a display. This is achieved using a pursuit camera setup. They are simply cameras which follow the on-screen motion and are extremely accurate at measuring motion blur, ghosting and overdrive artefacts of moving images. Since they simulate the eye tracking motion of moving eyes, they can be useful in giving an idea of how a moving image appears to the end user. It is the blurring caused by eye tracking on continuously-displayed refreshes (sample-and-hold) that we are keen to analyse with this new approach. This is not pixel persistence caused by response times; but a different cause of display motion blur which cannot be captured using static camera tests. Low response times do have a positive impact on motion blur, and higher refresh rates also help reduce blurring to a degree. It does not matter how low response times are, or how high refresh rates are, you will still see motion blur from LCD displays under normal operation to some extent and that is what this section is designed to measure. Further technologies specifically designed to reduce perceived motion blur are required to eliminate the blur seen on these type of sample-and-hold displays which we will also look at.

These tests capture the kind of blurring you would see with the naked eye when tracking moving objects across the screen (example from the Asus ROG Swift PG279Q). As you increase the refresh rate the perceived blurring is reduced, as refresh rate has a direct impact on motion blur. It is not eliminated entirely due to the nature of the sample-and-hold LCD display and the tracking of your eyes. No matter how fast the refresh rate and pixel response times are, you cannot eliminate the perceived motion blur without other methods.Tests like the above would give you an idea of the kind of perceived motion blur range when using the particular screen without any bur reduction mode active.

The Contrast Ratio of a TFT is the difference between the darkest black and the brightest white it is able to display. This is really defined by the pixel structure and how effectively it can let light through and block light out from the backlight unit. As a rule of thumb, the higher the contrast ratio, the better. The depth of blacks and the brightness of the whites are better with a higher contrast ratio. This is also referred to as the static contrast ratio.

When considering a TFT monitor, a contrast ratio of 1000:1 is pretty standard nowadays for TN Film and IPS-type panels. VA-type panels can offer static contrast ratios of 3000:1 and above which are significantly higher than other competing panel technologies.

Some technologies boast the ability to dynamically control contrast (Dynamic Contrast Ratio – DCR) and offer much higher contrast ratios which are incredibly high (millions:1 for instance!). Be wary of these specs as they are dynamic only, and the technology is not always very useful in practice. Traditionally, TFT monitors were said to offer poor black depth, but with the extended use of VA panels, the improvements from IPS and TN Film technology, and new Dynamic Contrast Control technologies, we are seeing good improvements in this area. Black point is also tied in to contrast ratio. The lower the black point, the better, as this will ensure detail is not lost in dark image when trying to distinguish between different shades.

Brightness as a specification is a measure of the brightest white the TFT can display, and is more accurately referred to as its luminance. Typically TFT’s are far too bright for comfortable use, and the On Screen Display (OSD) is used to turn the brightness setting down. Brightness is measure in cd/m2 (candella per metre squared). Note that the recommended brightness setting for a TFT screen in normal lighting conditions is 120 cd/m2. Default brightness of screens out of the box is regularly much higher so you need to consider whether the monitor controls afford you a decent adjustment range and the ability to reduce the luminance to a comfortable level based on your ambient lighting conditions. Different uses may require different brightness settings as well so it is handy when reviews record the luminance range possible from the screen as you adjust the brightness control from 100 to 0%.

The colour depth of a TFT panel is related to how many colours it can produce and should not be confused with colour space (gamut). The more colours available, the better the colour range can potentially be. Colour reproduction is also different however as this related to how reliably produced the colours are compared with those desired.

The colour depth of a panel is determined really by the number of possible orientations of each sub pixel (red, blue and green). These different orientations basically determine the different shade of grey (or colours when filtered in the specific way via RGB sub pixels) and the more “steps” between each shade, the more possible colours the panel can display.

Colour gamut in TFT monitors refers to the range of colours the screen is capable of displaying, and how much of a given reference colour space it might be able to display. It is ultimately linked to backlight technology and not to the panel itself.

Laser Displays are capable of producing the biggest colour gamut for a system with three basic colours, but even a laser display cannot reproduce all the colours the human eye can see, although it is quite close to doing that. However, in today’s monitors, both CRT and LCD (except for some models I’ll discuss below), the spectrum of each of the basic colours is far from monochromatic. In the terms of the CIE diagram it means that the vertexes of the triangle are shifted from the border of the diagram towards its centre.

Traditionally, LCD monitors were capable of giving approximate coverage of the sRGB reference colour space as shown in the diagram above. This is defined by the backlighting used in these displays – Cold-cathode fluorescent lamps (CCFL) that are employed which emit radiation in the ultraviolet range which is transformed into white colour with the phosphors on the lamp’s walls. These backlight lamps shine through the LCD panel, and through the RGB sub-pixels which act as filters for each of the colours. Each filter cuts a portion of spectrum, corresponding to its pass-band, out of the lamp’s light. This portion must be as narrow as possible to achieve the largest colour gamut.

To help develop and improve on the colour space a screen is capable of displaying a new generation CCFL backlighting was introduced. These so-called “wide gamut” backlights allow a gamut coverage of typically 92 – 102% of the NTSC colour space. There is a difference in practice which all users should be able to detect. The colour space available is extended mainly in green shades as you can see from the image above. Red coverage is also extended in some cases. This extended colour space sounds appealing on face value since the screens featuring WCG-CCFL backlighting can offer a broader range of colours. Manufacturers will often promote the colour space coverage of their screens with these high figures. In practice you need to consider what impact this would have on your use.

Of course the opposite is true if in fact you are working with content which is based on a wider colour space. In photography, the Adobe RGB colour space is often used and is wider than the sRGB reference. If you are working with wide gamut content, with wide gamut supported applications, you would want a screen that can correctly display the full range of colours. This could not be achieved using a traditional CCFL backlit display with only sRGB coverage, and so a wide gamut screen would be needed. Wide gamut displays are often aimed at colour enthusiasts and professional uses as a result.

LED backlighting has now become the norm for desktop monitors and is available in a few variations. The most common is White-LED (W-LED), which is a replacement for standard CCFL backlighting. The LED’s are placed in a line along the edge of the matrix, and the uniform brightness of the screen is ensured by a special design of the diffuser. The colour gamut is limited to sRGB as standard (around 68 – 72% NTSC) but the units are cheaper to manufacturer and so are being utilised in more and more screens, even in the more budget range. They do have their environmental benefits as they can be recycled, and they have a thinner profile making them popular in super-slim range models and notebook PC’s. It is possible to extend the colour gamut of W-LED displays using “Quantum Dot” technologies which are fairly new.

RGB LED backlighting consists of an LED backlight based on RGB triads, each triad including one red, one green and one blue LED. With RGB LED backlighting the spectrum of each LED is rather wide, so their radiation can’t be called strictly monochromatic and they can’t match a laser display, yet they are much better than the spectrum of CCFL and WCG-CCFL backlighting. RGB LED backlighting is not common yet in desktop monitors, and their price tends to put them way above the budget of all but professional colour enthusiast and business users. These models using RGB LED backlights are capable of offering a gamut covering > 114% of the NTSC colour space. They are not really used at all nowadays as they were prohibitively expensive.

There are also wide gamut LED backlights available and more commonly used nowadays as they are cheaper to manufacturer than older RGB LED versions. GB-r-LED for instance is provided by LG.Display and can offer wide gamut support from an LED backlight. Other panel manufacturers have their equivalents as well. Modern LED screens with wide gamut support tend to have a percentage coverage of the Adobe RGB reference space listed in the display spec, with 99% Adobe RGB being pretty standard for wide gamut LED technologies.

Viewing angles are quoted in horizontal and vertical fields and often look like this in listed specifications: 170/160 (170° in horizontal viewing field, 160° in vertical). The angles are related to how the image looks as you move away from the central point of view, as it can become darker or lighter, and colours can become distorted as you move away from your central field of view. Because of the pixel orientation, the screen may not be viewable as clearly when looking at the screen from an angle, but viewing angles of TFT’s vary depending on the panel technology used.

TFT screens do not refresh in the same way as a CRT screen does, where the image is redrawn at a certain rate. As a TFT is a static image, and each pixel refreshes independently, setting the TFT at a common 60Hz native refresh rate does not cause the same problems as it would on a CRT. There is no cathode ray gun redrawing the image as a whole on a TFT. You will not get flicker, which is the main reason for having a high refresh rate on a CRT in the first place. Standard TFT monitors operate with a 60Hz recommended refresh rate, but can sometimes support up to 75Hz maximum (within the spec) or sometimes even further using ‘overclocking’ methods. The reason that 60Hz is recommended by all the manufacturers is that it is related to the vertical frequency that TFT panels run at. Some more detailed data sheets for the panels themselves clearly show that the operating vertical frequency is between about 56 and 64Hz, and that the panels ‘typically’ run at 60Hz (see the LG.Philips LM230W02 datasheet for instance – page 11). If you decide to run your refresh rate from your graphics card above the recommended 60Hz it will work fine, but the interface chip on the monitor will be in charge of scaling the frequency down to 60Hz anyway. Some screens will allow you to run at the maximum 75Hz as well for an additional boost in frame rates and some minor improvements in motion clarity. The support of this will really depend on the screen, your graphics card and the video connection being used. You may find the screen operates fine at the higher refresh rate setting but in reality the screen will often drop frames to meet the 60Hz recommended setting (or spec of the panel) anyway. Generally we would suggest sticking to 60Hz on standard TFT monitors.

One thing which some people are concerned about is the frames per second (fps) which their games can display. This is one of the key reasons users will look to boost their screen beyond 60Hz. This is related to the refresh rate of your screen and graphics card. There is an option for your graphics card to enable a feature called Vsync which synchronizes the frame rate of your graphics card with the operating frequency of your graphics card (i.e. the refresh rate). Without vsync on, the graphics card is not limited in it’s frame rate output and so will just output as many frames as it can. This can often result in graphical anomalies including ‘tearing’ of the image where the screen and graphics card are out of sync and the picture appears mixed as the monitor tries to keep up with the demanding frame rate from the card. To avoid this annoying symptom, vsync needs to be enabled. With vsync on, the frame rate that your graphics card is determined by the refresh rate you have set in Windows. Capping the refresh rate at 60hz in your display settings limits your graphics card to only output 60fps. If you set the refresh at 75hz then the card is outputting 75fps. What is actually displayed on the monitor might be a different matter though as we explained above.

The desire to offer higher frame rate support and higher refresh rates has lead to panel manufacturers developing panels which can natively support 120Hz+. It is common now to see 120Hz or 144Hz as natively supported refresh rates. This allows much higher frame rates to be displayed and the increase in refresh rate also brings about positive improvements in perceived motion clarity. TN Film panels have been around for many years now with high refresh rates and in recent years there has been development in IPS-type and VA-type panels to boost their refresh rates as well. You will also now see some ‘overclocked’ monitors available where manufacturers have attempted to boost the refresh rate further. For instance the native 144Hz IPS-type panel of the Asus ROG Swift PG279Q up to 165Hz, or the 144Hz native VA-type panel of the Acer Predator Z35 up to 200Hz. Results of these overclocks do vary and are not guaranteed but may provide some additional benefits.

True 120HZ technology– to have a true 120Hz screen, it must be capable of accepting a full 120Hz signal output from a device (e.g. a graphics card). Because TV’s are limited at the moment by their input sources they tend to use the above interpolation technology, but with the advent of 3D TV and higher frequency input sources, this will change. Desktop monitors are a different matter though as graphics cards can obviously output a true 120Hz if you have a decent enough card. Some models can accept a 120Hz signal but need different interfaces to cope (e.g. dual-link DVI or DisplayPort).

This relates to the connection typ