1.8 inch spi tft lcd display module price

Description:The ST7735R full color TFT display module is an SPI protocol based display with a resolution of 128*160 pixels and 1.8 inch size. It displays up to 262,144 different colors. The module has its own pixel-addressable frame buffer which means it can be used with all kinds of microcontroller with only 4 i/o pins. This module also comes by an SD card slot on which colored bitmaps can be loaded and easily displayed on the screen.The TFT Display communicates with the microcontroller over SPI protocol, so you need to connect it to the SPI pins of the Arduino. Before connecting it directly to the 5v logic level of the Arduino, ensure that has a voltage regulator. Because the display may be destroyed if the version of the display you have does not have the regulator. If the display does not have a voltage regulator, you can use any logic level converter between the display and the Arduino

This lovely little display breakout is the best way to add a small, colorful, and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.8″ display has 128×160 color pixels. Unlike the low-cost Nokia 6110 and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 18-bit color (262,144 shades!). And the 1.8 Inch SPI 128×160 TFT LCD Display Module will always come with the same driver chip so there are no worries that your code will not work from one to the other. The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. It features a microSD card holder so you can easily load full-color bitmaps from a FAT16/FAT32 formatted microSD card.

A wide variety of tft display 1.8 options are available to you, You can also choose from original manufacturer, odm and agency tft display 1.8,As well as from tft, ips, and standard.

Key words: tft 1.8", 1.8 tft lcd, 1.8" tft lcd, 1.8 inch tft lcd, tft lcd 1.8, 1.8 tft display, 1.8" tft display, 1.8 inch tft display, tft display 1.8, tft display 1.8", 1.8 tft lcd, tft 1.8

In this guide we’re going to show you how you can use the 1.8 TFT display with the Arduino. You’ll learn how to wire the display, write text, draw shapes and display images on the screen.

The 1.8 TFT is a colorful display with 128 x 160 color pixels. The display can load images from an SD card – it has an SD card slot at the back. The following figure shows the screen front and back view.

This module uses SPI communication – see the wiring below . To control the display we’ll use the TFT library, which is already included with Arduino IDE 1.0.5 and later.

The TFT display communicates with the Arduino via SPI communication, so you need to include the SPI library on your code. We also use the TFT library to write and draw on the display.

In which “Hello, World!” is the text you want to display and the (x, y) coordinate is the location where you want to start display text on the screen.

The 1.8 TFT display can load images from the SD card. To read from the SD card you use the SD library, already included in the Arduino IDE software. Follow the next steps to display an image on the display:

Note: some people find issues with this display when trying to read from the SD card. We don’t know why that happens. In fact, we tested a couple of times and it worked well, and then, when we were about to record to show you the final result, the display didn’t recognized the SD card anymore – we’re not sure if it’s a problem with the SD card holder that doesn’t establish a proper connection with the SD card. However, we are sure these instructions work, because we’ve tested them.

In this guide we’ve shown you how to use the 1.8 TFT display with the Arduino: display text, draw shapes and display images. You can easily add a nice visual interface to your projects using this display.