2.4 tft lcd touch shield for uno and mega pricelist

Spice up your Arduino project with a beautiful touchscreen display shield with built in microSD card connection. This TFT display is 2.4" diagonal and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional capacitive touch panel and resistive touch panel with controller XPT2046 attached by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

Spice up your Arduino project with a beautiful touchscreen display shield with built in microSD card connection. This IPS TFT display is 2.4" diagonal and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional capacitive touch panel and resistive touch panel with controller XPT2046 attached by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

1.2.4 inch arduino shield with resistive touch panel could only support Due board. It can support DUE,UNO,MEGA2560 boad if matched with capacitive touch panel.

2.If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

Features: 2.4 diagonal LCD TFT display Bright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for backlight control Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2,3 and analog 4 and 5. Pin 12 is available if not using the micro SD 5V compatible, use with 3.3V or 5V logic For Arduino UNO R3 Specifications: Size: 72 x 52 x 12 mm Weight: 33 g Package weight: 43 g Package included: 1 x 2.4 TFT LCD Shield SD Socket Touch Panel Module.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

This module is designed to plug directly into Arduino UNO R3 (or its clone) boards. It is compatible with CH340 and Atmega16u2 version boards, as well as Mega 2560. This LCD shield may also work with other boards, but the compatibility can"t be guaranteed.

Ordered 2 screens and both arrived with driver chip damaged. seller did not offer any technical support, apparently has no technical background. Seller offered me a full refund, but ask me to send back damaged screens with free return label. I lost many hours trying figure out what is going on with these screens, don"t feel like spend more time or money on this seller. Waste of time avoid. Don"t recommend at all.

Afghanistan, Algeria, American Samoa, Andorra, Angola, Argentina, Armenia, Bahrain, Bangladesh, Belarus, Benin, Bermuda, Bhutan, Bolivia, Botswana, Brunei Darussalam, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde Islands, Central African Republic, Central America and Caribbean, Chad, China, Comoros, Congo, Democratic Republic of the, Congo, Republic of the, Cook Islands, Côte d"Ivoire (Ivory Coast), Djibouti, Egypt, Equatorial Guinea, Eritrea, Ethiopia, Falkland Islands (Islas Malvinas), Fiji, French Guiana, French Polynesia, Gabon Republic, Gambia, Georgia, Ghana, Gibraltar, Greenland, Guam, Guernsey, Guinea, Guinea-Bissau, Guyana, Hong Kong, Iceland, India, Indonesia, Iraq, Jersey, Jordan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Lebanon, Lesotho, Liberia, Libya, Liechtenstein, Macau, Madagascar, Malawi, Mali, Marshall Islands, Mauritania, Mauritius, Mayotte, Micronesia, Mongolia, Morocco, Mozambique, Namibia, Nauru, Nepal, New Caledonia, Niger, Nigeria, Niue, Oman, Pakistan, Palau, Papua New Guinea, Qatar, Reunion, Russian Federation, Saint Helena, Saint Pierre and Miquelon, San Marino, Saudi Arabia, Senegal, Seychelles, Sierra Leone, Solomon Islands, Somalia, South Africa, Sri Lanka, Suriname, Svalbard and Jan Mayen, Swaziland, Tajikistan, Tanzania, Togo, Tonga, Tunisia, Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, Uzbekistan, Vanuatu, Vatican City State, Venezuela, Vietnam, Wallis and Futuna, Western Sahara, Western Samoa, Yemen, Zambia, Zimbabwe

2.4 inch TFT LCD Touch Screen Shield for Arduino UNO R3 Mega2560The shield is fully assembled, tested and ready to go. No wielding, no solder! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic UNO. This shield does work with the Mega but its going to be half the speed of the Uno-type boards because of the way the Mega rearranges all the pins (there is no way to get around this!) This shield is Leonardo-compatible

Description:Spice up your project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.4 inch diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.color: redMaterial: comprehensive material

Technical Details:2.4 inch diagonal LCD TFT display240x320 resolution, 18-bit (262,000) colorspfd5408 controller with built in video RAM buffer8 bit digital interface, plus 4 control linesUses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if using the microSDWorks with any "328 or Mega (Leonardo supported yet)5V compatible! Use with 3.3V or 5V logicOnboard 3.3V 300mA LDO regulator4 white LED backlight. On by default but you can connect the transistor to a digital pin for backlight control4-wire resistive Press screenPackage Contents:1* 2.4 inch TFT LCD screen1* Pen

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

For this tutorial I composed three examples. The first example is distance measurement using ultrasonic sensor. The output from the sensor, or the distance is printed on the screen and using the touch screen we can select the units, either centimeters or inches.

The next example is controlling an RGB LED using these three RGB sliders. For example if we start to slide the blue slider, the LED will light up in blue and increase the light as we would go to the maximum value. So the sliders can move from 0 to 255 and with their combination we can set any color to the RGB LED,  but just keep in mind that the LED cannot represent the colors that much accurate.

The third example is a game. Actually it’s a replica of the popular Flappy Bird game for smartphones. We can play the game using the push button or even using the touch screen itself.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

As the code is a bit longer and for better understanding I will post the source code of the program in sections with description for each section. And at the end of this article I will post the complete source code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

Next we need to define the fonts that are coming with the libraries and also define some variables needed for the program. In the setup section we need to initiate the screen and the touch, define the pin modes for the connected sensor, the led and the button, and initially call the drawHomeSreen() custom function, which will draw the home screen of the program.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

Next is the distance sensor button. First we need to set the color and then using the fillRoundRect() function we will draw the rounded rectangle. Then we will set the color back to white and using the drawRoundRect() function we will draw another rounded rectangle on top of the previous one, but this one will be without a fill so the overall appearance of the button looks like it has a frame. On top of the button we will print the text using the big font and the same background color as the fill of the button. The same procedure goes for the two other buttons.

Now we need to make the buttons functional so that when we press them they would send us to the appropriate example. In the setup section we set the character ‘0’ to the currentPage variable, which will indicate that we are at the home screen. So if that’s true, and if we press on the screen this if statement would become true and using these lines here we will get the X and Y coordinates where the screen has been pressed. If that’s the area that covers the first button we will call the drawDistanceSensor() custom function which will activate the distance sensor example. Also we will set the character ‘1’ to the variable currentPage which will indicate that we are at the first example. The drawFrame() custom function is used for highlighting the button when it’s pressed. The same procedure goes for the two other buttons.

getDistance(); // Gets distance from the sensor and this function is repeatedly called while we are at the first example in order to print the lasest results from the distance sensor

So the drawDistanceSensor() custom function needs to be called only once when the button is pressed in order to draw all the graphics of this example in similar way as we described for the home screen. However, the getDistance() custom function needs to be called repeatedly in order to print the latest results of the distance measured by the sensor.

Here’s that function which uses the ultrasonic sensor to calculate the distance and print the values with SevenSegNum font in green color, either in centimeters or inches. If you need more details how the ultrasonic sensor works you can check my particular tutorialfor that. Back in the loop section we can see what happens when we press the select unit buttons as well as the back button.

Ok next is the RGB LED Control example. If we press the second button, the drawLedControl() custom function will be called only once for drawing the graphic of that example and the setLedColor() custom function will be repeatedly called. In this function we use the touch screen to set the values of the 3 sliders from 0 to 255. With the if statements we confine the area of each slider and get the X value of the slider. So the values of the X coordinate of each slider are from 38 to 310 pixels and we need to map these values into values from 0 to 255 which will be used as a PWM signal for lighting up the LED. If you need more details how the RGB LED works you can check my particular tutorialfor that. The rest of the code in this custom function is for drawing the sliders. Back in the loop section we only have the back button which also turns off the LED when pressed.

In order the code to work and compile you will have to include an addition “.c” file in the same directory with the Arduino sketch. This file is for the third game example and it’s a bitmap of the bird. For more details how this part of the code work  you can check my particular tutorial. Here you can download that file:

getDistance(); // Gets distance from the sensor and this function is repeatedly called while we are at the first example in order to print the lasest results from the distance sensor

The 2.4 inch TFT Touch Screen Module with micro SD card slot is now available as a SHIELD for Arduino UNO. It has a four wire resistive touch screen, a micro SD card socket, a reset switch and a convenient Arduino Uno shield footprint.

You may return most new, unopened items within 30 days of delivery for a full refund. We"ll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).

Features:2.4" diagonal LCD TFT Touch Panel displayBright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for backlight controlColorful, 18-bit 262,000 different shades4-wire resistive touchscreen8 bit digital interface, plus 4 control linesUses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD5V compatible, use with 3.3V or 5V logicFor Arduino UNO R3 MEGA2560

This module is designed to plug directly into Arduino UNO R3 (or its clone) boards. It is compatible with CH340 and Atmega16u2 version boards, as well as Mega 2560. This LCD shield may also work with other boards, but the compatibility can"t be guaranteed.

The shield is fully assembled, tested, and ready to go. No wiring, no soldering! Simply plug it in and load up the library - you"ll have it running in under 10 minutes!

The 2.4 inch TFT LCD touch screen module suitable for Arduino, provides a large touchscreen display shield with a built in microSD socket offering a high resolution colourful display to your Arduino.

Andhra Pradesh, Arunachal Pradesh, Assam, Bihar, Chhattisgarh, Goa, Gujarat, Haryana, Himachal Pradesh, Jammu and Kashmir, Jharkhand, Karnataka, Kerala, Madhya Pradesh, Maharashtra, Manipur, Meghalaya, Mizoram, Nagaland, Orissa, Punjab, Rajasthan, Sikkim, Tamil Nadu, Telangana, Tripura, Uttaranchal, Uttar Pradesh, West Bengal and major cities including Ahmednagar, Aizawl, Ajmer, Akola, Alappuzha, Aligarh, Allahabad, Alleppey, Almora, Alwar, Amarnath, Ambattur, Ambernath, Amravati, Amritsar, Anantagir, Anantapur, Andaman, Araku, Arrah, Asansol, Aurangabad, Avadi, Ayodhya, Ayurveda, Badrinath, Bally, Bandhavgarh, Bangalore, Baranagar, Barasat, Bardhaman, Bareilly, Baroda, Bastar, Bathinda, Beach, Beaches, Begusarai, Belgaum, Bellary, Bhagalpur, Bharatpur, Bhatpara, Bhavnagar, Bhilai, Bhilwara, Bhimtal, Bhiwandi, Bhopal, Bhubaneswar, Bhuj, Bidar, Bihar, Bijapur, Bikaner, Bilaspur, Bird, Bodh, Bokaro, Brahmapur, Bulandshahr, Calicut, Chail, Chamba, Chandigarh, Chandrapur, Chennai, Chennai, Cherai, Cherrapunji, Chidambaram, Chikhaldara, Chopta, Coimbatore, Coimbatore, Coonoor, Coorg, Corbett, Cotigao, Cuttack, Dadra, Dalhousie, Daman, Darbhanga, Darjeeling, Davanagere, Dehradun, Delhi, Devi, Devikulam, Dewas, Dhanaulti, Dhanbad, Dharamashala, Dhule, Dindigul, Diu, Dudhwa, Durg, Durgapur, Dwaraka, Etawah, Faridabad, Farrukhabad, Firozabad, Flowers, Gandhidham, Gandhinagar, Gangotri, Gangtok, Gaya, Ghaziabad, Gir, Goa, Gopalpur, Gorakhpur, Great, Gulbarga, Gulmarg, Guntur, Gurgaon, Guruvayoor, Guwahati, Gwalior, Hampi, Hapur, Haridwar, Haveli, Hills, Himalayan, Hisar, Hogenakkal, Horsley-Hills, Howrah, Hubballi-Dharwad, Hyderabad, Hyderabad, Ichalkaranji, Idukki, Imphal, Indore, Islands, Itangar, Jabalpur, Jaipur, Jaisalmer, Jalandhar, Jalgaon, Jalna, Jammu, Jamnagar, Jamshedpur, Jhansi, Jodhpur, Junagadh, Kadapa, Kakinada, Kalyan-Dombivali, Kamarhati, Kanchipuram, Kanha, Kanpur, Kanyakumari, Karawal Nagar, Kargil, Karimnagar, Karnal, Karwar, Katihar, Kausani, Kedarnath, Keoladeoghana, Khajuraho, Khammam, Kirari Suleman Nagar, Kochi, Kodaikanal, Kolhapur, Kolkata, Kollam, Konark, Korba, Kota, Kotagiri, Kottakkal, Kovalam, Kozhikode, Kudremukh, Kullu, Kulti, Kumaon, Kumarakom, Kurnool, Kurukshetra, Lakshadweep, Latur, Life, Loni, Madurai, Malpe, Manas, Mango, Maravanthe, Margoa, Mau, Meerut, Mira-Bhayandar, Mirzapur, Moradabad, Mount, Mumbai, Mussoorie, Muzaffarpur, Nalanda, Nanda, Nanded, Nandi-Hills, Nashik, National, Navi Mumbai, Nellore, Netravali, Nizamabad, Noida, North Dumdum, Orchha, Ozhukarai, Pali, Panipat, Parbhani, Patiala, Patnitop, Pattadakkal, Pondicherry, Puducherry, Pune, Puri, Purnia, Pushkar, Rajahmundry, Rajgir, Rameshwaram, Rampur, Ranchi, Ranikhet, Ranthambore, Rohtak, Rourkela, Sagar, Sangli-Miraj & Kupwad, Sariska, Satna, Shillong, Sikar, Solapur, South Dumdum, Sri Ganganagar, Srinagar, Surat, Tezpur, Thane, Thanjavur, Thiruvananthapuram, Thoothukudi, Thrissur, Tiruchirappalli, Tirunelveli, Tirupati, Tirupur, Tumkur, Udaipur, Ujjain, Vaishali, Vasai-Virar, Visakhapatnam, Vishakhapatnam, Vizianagaram, Warangal, Warangal, Wayanad, Yercaud, Zanskar, Nagpur etc. You may buy latest electronics components, accessories and development boards from us at affordable prices. Buy Raspberry Pi, Arduino, AVR, ARM, 8051 Development Boards, Wireless and Wired, Microcontroller and ICS, Robotics & Accessories, Prototyping Components, Educational Kits etc. We also provide technical assistance for products purchased from our store and supplement it with schematics, code examples and demonstrations.

OVERVIEW:The 2.4″ Colour TFT display with a micro SD card slot is now available as a SHIELD for Arduino UNO.It has a four-wire resistive touch screen, a micro SD card socket, a reset switch, and a convenient Arduino Uno shield footprint.Features:2.4-inch LCD TFT display has Bright, 4 white-LED backlights.Colorful, 18-bit 262,000 different shades4-wire resistive touchscreen240 x 320 resolutionSpfd5408 controller with built-in video RAM buffer8-bit digital interface, plus 4 control linesUses digital pins 5-13 and analog 0-3. Digital pins 2, 3, and analog 4 and 5 are available for user-defined purposes. Pin 12 is available if micro SD is not used.5V compatible can be used with 3.3V or 5V logicSize: 71 x 52 x 7mmDocument: