sainsmart 3.2 tft lcd display tutorial factory

SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

There is built-in SD card slot in the shield, so we can use it to upload images. But the images need to be converted RAW format first.You can use the tool here. SD libraries need to be preinstalled for displaying the image.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touch screen. The LCD is well mated with Pi board and interface with Pi via the high speed SPI port, and support console, X windows, displaying images or video etc. It also provides 4 press buttons for user defined functions.

RPi LCD needs to use a SPI interface, but in the original image file of Raspberry Pi, the displayer is driven via a HDMI port. So the original image is not applicable for RPi LCD, and you should install the LCD driver to your Pi or use the Ready-to-use image file provided by Sainsmart,click here.

Download the LCD driver and extract it to your Raspbian OS (e.g. copy the driver to your Pi by sftpor using U disk). Then run the following command via putty:

This LCD can be calibrated using a program called xinput_calibrator which is pre-installed on the offer image. However, it was not pre-installed on original Raspbian OS. So in this case, you should get and install the program manually with

After running these commands, there will be a prompt for four-point calibration shown in the LCD screen. Click the points one by one to finish the touch calibration. Then, the new calibration data will be displayed in the terminal, as shows below. Please get these data for future use.

SainSmart 3.2" TFT LCD Displayis a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

Reason: The hooks on the backight of ER-TFT032-3.1 is always complained by most customers for inconvenient assembly. So we cancel the hooks in the new version of ER-TFT032-3.2.That"s the only difference for these two versions.

ER-TFT032-3.2 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller and optional 4-wire resistive touch panel and 3.2 inch capactive touch panel with controller FT6236,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8/16-bit parallel,3/4-wire serial interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

ER-TFTM032-3 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card .It"s optional 3.2 " 4-wire resistive touch panel with controller XPT2046 and 3.2 " capacitive touch panel with controller FT6236 . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

Buying is a Type of Hunting Game. TFT LCD Display For Arduino Buying Guide is an Important Article as No Where There is Any Practical Guide. Practically we will use it as a base either as receiver or the central machinery for some stuffs around Internet of Things. Just for getting started with DIY electronics, we published some articles which possibly will help who are not exactly related to hardware but has more to do with software. Those articles mostly can be found by using the search option on this website, searching with Arduino will help to sort out.

We are avoiding the basic electronic displays like LED display, basic LCD display as we are NOT really related to so basic works of electronics. This website was never for so basic guides. There are hundreds of those basic websites for those guides. Hardware are time consuming to write, most importantly, testing the useless hardware hugely waste our space. It might dishearten our some readers, but basically we need a rapid shift towards our main niche. Ultimately we have to connect with the servers.

We will, ultimately work with creating devices related to Internet of Things. As we discussed before – mobile phone’s display is not exactly a time and cost saving option as alternative display.

We have three options – TFT LCD Display, TFT LCD Touch Display and OLED display. You can check various places, monochrome OLEDs are the choice right now for manufacturing electronic units. OLEDs are hugely power saving but are far better than monochrome LCDs. There is not HUGE options in OLEDs for Arduino. Usage is very lesser in most situations where we will need a display. TFT LCD Touch Display doubles up as an input too. Without a computer, we can do the desired works in the way, suppose we did with the old color mobile phones. Smartphones are mostly a full OS driven, hence can not be compared. Most works which other displays can perform a TFT LCD Touch Display is able to perform.

There are several things to consider. First, it is basically meaningless to buy a bigger display at higher cost. Second, we do not need Mac like beautiful display. Third, connecting the display with various types of Arduino is not exactly very easy. Forth, even the official TFT LCD Touch Display library of Arduino is not fully complete, Adafruit has Open Source contribution. Fifth, there is a firmware of the whole thing, it is kind of “self dependent”. If a cheaper stuff’s library or firm is not compatible, no body’s father reverse engineer it.

We found two company’s name for 2.4″ TFT LCD Touch Displays – one is LuckSender, whose product sold around $4.99 in Ebay, but has a serious detailed pathetic, scary review by an Amazon customer. It probably has problem with compatibility.

Second company we found is named SainSmart. SainSmart is not exactly a small company, it has a modern website (we saw Affiliate link option in footer too – we are never interested to push anyone’s product to our readers), We noticed that, this company’s website has written :

But also we noticed that, SainSmart 3.2″ TFT LCD Display total unit for Arduino sells at Ebay at LESSER price than official website with free shipping. You can probably use the SainSmart’s forum for support. This display stuffs is probably less explored market.

For those who have lesser idea, this total stuff includes a board (shield) and a SD card slot too. $13.00 is not bad pricing for a TFT LCD Touch Display, although (as always) we think, the right price should be $1.30! We are kids, playing, we can not make money out of these, they should “sponsor” us. The market of Arduino is not exactly great right now unlike before, their monopoly is only in boards; Adafruit also not going great. Except display, the market is of China. Do not hurry, watch auctions and it is not improbable to get that brand’s at less than $10.00.

The 2.8" Arduino TFT LCD Touchscreen Module (Colour Screen) is for Arduino UNO board and Mega 2560 board or boards compatible with UNO. This module can display words, colour painting, ghaphics and pictures. This module come with a large touch screen display and build in Micro SD Card socket make it user friendly and easy to use. As a bonus, this display comes with a resistive or capacitive touchscreen attached to it , so you can detect finger presses anywhere on the screen.

Over the past year, I"ve ordered 47 of these SainSmart LCD displays. For a while, they had a good thing going, but in the Autumn of 2015, they changed their manufacturing and have utterly messed up this device. The first six that I ordered in the Summer of 2015 worked perfectly. But of the 41 devices that I"ve ordered after the change, 40% have failed right out of the box... 6 won"t power up at all, 4 have screen flicker, 2 the touch doesn"t work, 1 the LCD pixels were misaligned and 1 had a cracked screen. What happened? Besides utter lack of quality control (these displays were obviously never tested), SainSmart changed the LCD screen hardware. Instead of using the LCD screen that would fit properly on the TFT_320QVT PCB (see pictures), they chose a slightly thinner, narrower LCD screen that normally fits the TFT_320QDT PCB. (notice the one letter difference). The problem is that the new screen DOES NOT FIT properly into the pin holes on the PCB and has a nasty habit of falling off (see pics). They obviously realized this at the factory, and rather than re-ordering the correct screens, they just tried to force them to stay on with double sided tape. But that hasn"t worked well. Many of my screens had fallen off by the time I received them! But because I own a business that uses these things and I didn"t know at the time that I could find alternative suppliers for this part, my work-around was to glue them into the best position possible using a hot glue gun. What a pain! Moral of the story: Don"t order any of these from SainSmart LCDs until they have accepted they have screwed this up and fixed this problem. I suspect they will comment on this review once that has happened and I"ll make modifications to this review to let you know when the problem is fixed. Until then, BUYER BEWARE. And, any other SainSmart product that includes this 3.2" is very likely going to include this same problem - including the shield + LCD and Mega2560 + shield + LCD. That all said, when this thing works, it works really well. I am satisfied with resolution and the touch is responsive. I use it in the product that our company sells. Just don"t get it from Sainsmart - for now. There are alternative suppliers.A couple final technical notes:* The SD slot will not work with any SDHC cards. And no, you can"t reformat a larger SDHC card down to 2GB and get it to work. Won"t work. You can however get a 2GB or 4GB SD Card (not SDHC) and it"ll work fine. You may see some documentation suggesting a 2GB limitation, but it"s really 4GB as long as you don"t use a SDHC card. Did I mention, do not use SDHC? If you need to understand the difference, google "SD vs SDHC".* The screen IC driver comes in two flavors out there: SSD1289 and ILI9341. They both work, but the software configuration is slightly different. So, either use one or the other - or expect to somehow auto-detect which one connect to your Mega2560 (not possible directly) and then code for both possibilities. As far as I can tell, the SSD1289 is being phased out for the now more common ILI9341. I"ve ordered this device from a number of sites, but unfortunately they often list the item as SSD1289, but it arrives as a ILI9341. If you are new to this, my advice is to go with the ILI9341 driver. The UTFT library was updated in the Summer of 2016 to accommodate this newer driver. Another reason to pass on this Sainsmart device is that it uses the SSD1289 driver. How can you tell the difference? The model for SSD1289 is TFT_320QVT and the model for ILI9341 is TFT_320QVT_9341. Unfortunately, ads for these devices often have the wrong model number displayed!