tft lcd display touch panel spi ili9341 supplier

ER-TFT022-1 is 240x320 dots 2.2" color tft lcd module display with ILI9341 controller,optional capacitive touch panel with controller FT6236U and resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.2"TFT Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno.For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

After spending way too much time trying to figure out the touchscreen, I wanted to share what finally worked for me! First, I"ll share the pinout. Next, I"ll share the steps that worked with the eSPI library. Lastly, I"ll show you the steps using an alternative library - the XPT2046_Touchscreen library.

Let me just say it was initially confusing to me because the ILI9341 is the display, but the touchscreen is actually controlled by an XPT2046. And I struggled with connecting everything properly to an ESP-WROOM-32 ESP32 ESP-32S dev board.

5. Open the eSPI "User_Setup.h" file. This file contains the TFT_eSPI configuration. By default, I think the Arduino IDE would have installed this file (step 3 above) in this location: C:\Users\\Documents\Arduino\libraries\TFT_eSPI\User_Setup.h

9. Compile and upload the sketch. Given that we configured the pinout in step 6 above, there should be no need to make any changes to the code in the Touch_calibrate example.

11. On the ILI9341 screen, you should be prompted to touch each of the 4 corners of the screen to calibrate it. I recommend using the stylus since the calibration requires precise taps.

14. You"ll be happy to hear that the other TFT_eSPI examples should work right out with this same pinout. One of my favorites is TFT_Starfield. Just make sure to select an example that"s 320x240 to match the ILI9341 resolution.

8. The ILI9341 screen will be completely white, but don"t panic. The screen is supposed to be blank white because this example tests only the touch aspect of the ILI9341, not the display aspect.

WF28E is full color 240xRGBx320 TFT LCD display module, diagonal size 2.8 inch. This module is built in with ILI9341V IC; it supports 8/ 16bit 8080-series Parallel MCU Interface. WF28E model is having module dimension of 50.0 x 69.2 mm and Active area size of 43.2 x 57.6 mm; it integrated ILI9341V controller on module, logic supply voltage range from 2.5V to 3.3V.

WF28E is portrait mode LCD module, if you would like to use it as landscape mode, please contact with us for more technical support. This 2.8” TFT LCD module is featured with brightness 500 cd/m2(typical value), it can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃. This 2.8" TFT LCD Module 6:00 o"clock viewing direction works well for devices that is easy to read above eye level without fading, such as signal analyzers or bench top laboratory equipment, handhold microscope and other handhold devices.

Search keyword: ili9341 tft display, tft 2.8", 2.8 tft lcd, 2.8" tft lcd, 2.8 inch tft lcd, tft lcd 2.8, 2.8 tft display, 2.8" tft display, 2.8 inch tft display, tft display 2.8, tft display 2.8"