5in lcd touch screen raspberry pi factory

5inch Resistive Touch Screen LCD with HDMI interface,this LCD features HDMI and VGA interfaces for display, USB interface for touch.Could work as a touchscreen of Raspberry Pi and some mini PC. It could also workwith Windows computer.

2.The LCD can work with Raspbian, Ubuntu, WIN10 IOT and so on. With some OS may cannot work properly. If you cannot confirm if your OS is supported, you can contact us and provide the image, we could test it for you if possible.

※Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

All the accessories listed below tier pricing need to pay.We won"t deliver until you select. Power adaptor should be 5V/2000mA in output and center pin for positive voltage and the outer shield for negative voltage .The temperature for controller RTD2660 would increase during working.That"s normal phenomenon,not quality problem.

ER-TFTV050A1-1 is 480x272 dots 5" color tft lcd module display with small HDMI signal driver board,optional capacitive touch panel with USB controller board and cable and 4-wire resistive touch panel with USB driver board and cable, optional remote control,superior display quality,super wide view angle.It can be used in any embedded systems,car,industrial device,security and hand-held equipment which requires display in high quality and colorful video. It"s also ideal for Raspberry PI by HDMI.

Hardware ConnectionPlug the LCD to your Raspberry Pi:There are 40 pins on Raspberry Pi Model A+/B+/2 B/3 B but only 26 pins on the LCD, so you should pay attention to connecting the pins to your Pi accordingly.

Connect the HDMI Connector to both the HDMI interfaces on the LCD and the Pi.You should connect the LCD to Raspberry Pi Model B or Raspberry Pi Zero with an HDMI cable rather than an HDMI Connector.

Note: This product can only work on a Raspberry Pi but not work on a PC. That is, if the HDMI of the LCD is connected to the HDMI on a PC, the LCD doesn"t display anything.

You can enable the touch in two ways: Method 1. install driver to your Raspbian/Ubuntu Mate OS. Method 2. use the Ready-to-use image file of which LCD driver was pre-installed.

2) Connect your micro SD card to the PC and write the image to the card using Win32DiskImager. How to write an image to a micro SD card for your Pi? See RPi Image Installation Guides for more details)

5) The LCD will display after booting up. Then open a terminal to install the touch driver which can be found in the /boot/ directory. Note: The Raspberry Pi must be connected to the network, or else the touch driver won"t be successfully installed. The result is that a small area at the border cannot be touched. If you have installed the touch driver but without network connection, how to solve the problem? See:git clone https://github.com/waveshare/LCD-show.git

If a latest Raspbian OS is in used, you should connect your Pi to the internet and install xserver-xorg-input-evdev.sudo apt-get install xserver-xorg-input-evdevJust be sure that evdev.conf has a higher number than 40-libinput.conf. For example, rename 10-evdev.conf to 45-evdev.conf. this forces evdev to load after libinput.sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf

Install it with the commands:sudo dpkg -i -B xinput-calibrator_0.7.5-1_armhf.debClick the "Menu" button on the task bar, choose "Preference" -> "Calibrate Touchscreen".

You can create a 99-calibration.conf file to save the touch parameters (not necessary if file exists)./ect/X11/xorg.conf.d/99-calibration.confSave the touch parameters (may differ depending on LCD) to 99-calibration.conf, as shown in the picture:

DF tech is a leader manufacturer which is located in Shenzhen,and has more than 10 years of experience in the production of P+G ,G+G , G+FF touch screens and full bonding assembly. We have professional team and technician to provide professional technical services and products for many industries, commerce, and home automation,etc.

DF tech has been paying attention to the constantly updated technology of the market to solve all special needs of customers in touch and display.The size is cover a range from 2.4 inches to 32 inches.