lcd panel cof repair pdf manufacturer

1. #Confirm whether the COF on side X is hot compared with the normal temperature, whether there is fracture or wear crack, and whether the COF is burnt.

2. #Confirm whether the VAA is normal (normally about 17V). If abnormal, disconnect the RP32 to confirm whether it is caused by DC/DC loop or X-side COF: disconnect RP32, if the VAA is normal, the COF is bad, CO must be changed; COF can be Disconnect one by one to determine which NG disconnects RP32, VAA NG, try to change UP1; at the same time, confirm whether the continuity of the surrounding triode is OK.

3. #Confirm whether the RSDS value is correct, normal RSDS is about 1.2v, and the signal difference is about 200mV; At the same time, we can confirm the resistance between RSDS signal (normal 100 or 50 ohms) and RSDS resistance to ground. If the voltage is NG, check if the ASIC and X-COF are hot.

2. #Confirm VGH/VGL voltage (about 30V VGH and -6v VGL), and confirm whether it is DC/DC loop NG or COF IC NG; The corresponding resistance of disconnected VGH and VGL can determine whether it is a DC/DC problem or a COF-IC problem. If it is DC/DC NG, try to replace UP1 or confirm whether the corresponding transistor is OK.

3. #Confirm whether the gate IC is OK. There is a signal test point on the back of COG IC, which can scrape the green paint for measurement confirmation; Or cut COF halfway from G3. If there is a gate-ic problem, which IC fault can be confirmed.

B. Confirm VAA resistance to ground at VAA test point of R plate (A short circuit usually occurs), disconnect the corresponding capacitance of the following 3 COF, and confirm VAA resistance to the ground again. If OK, replace the capacitor, if NG, replace COF. If VAA is still NG, confirm DC/DC loop as all models.

3. #Shaking module, if vertical lines disappear or reappear, then it can be judged that the possible cause is COF pin broken, and the crease should be found under the OM microscope.

4. #Press the LCD glass side of the panel, if the vertical lines disappear or reappear, it can be judged that the cause of poor contact, OM checking should be able to find the poor contact.

5. #If there is no display change in pressing, confirm whether ITO is damaged under the OM microscope, or pin signal waveform corresponding to needle COF.

The above is the full text of LCD screen failure repair guide, we hope it is helpful to you. If you need to buy LCD and find a reliable LCD supplier, we suggest you to read our other great blog – How to find a reliable LCD supplier.

Founded in 2014, VISLCD is a professional LCD supplier. We provide LCD modules, touch LCD and customized LCD in various sizes with stable quality and competitive price. Welcome to contact us for any LCD demand, thank you.

LCD&LED Screen Repair Machine Manufacturers And SalesLCD&LED Screen Repair Technology TrainingMore details contact meWhatsApp/WeChat：+8613760635784Phone：+861...

India"s Single Manufacturer and exporters of Panel Repair Factory India Pvt Ltd. Manufacturing top quality products for PRF 960C LCD Panel Repairing Machine and giving good services to customers and provides free installation, free training, free accessories on a purchase of Bonding Machine.

Panel Repair Factory India Pvt Ltd. Provides the best LCD Panel Repair Machine. LCD panel repair machine is great and best solutions for panel repair in bonding technology, this is the most high-end technology of LCD screen repair ,LED screen repair, in repair industry in addition to the COF loose welding, LCD TAB bonding machine others such as ITO break, short line, bright line, half-line, dotted line ,a multi-line bonding machine can be used to repair.

ACF Bonding Machine Prf 960 is an LCD repair machine that fixes the problem of dual pictures, Linning Appearance on screens and chip damage on LCD. It works on highly advanced technology performed on PRF 960 bonding machine. This Machine takes up to 7-10 minutes to repair one unit at a time. The company provides full disclosure regarding products detailed information and how to perform Repairing activity during LCD repairs.

*The Response timing in temperature"s case is 3-4 seconds from room temperature to 180 degrees. The temperature curve can always be adjusted. The peak temperature has small errors in some +/- °C. COF accurate alignment, LCD repair success rate is high.

PRF-999 ACF Bonding Machine is Export Model slim & sleek designed machine. This LCD repair Bonding Machine fixes the COF driver inbuilt makes it more adopting on-screen display. As a previously mentioned machine, this machine does take the same amount of time to repair the LCD screen.