raspberry pi tft display 3.5 quotation

Is this not the cutest, little display for the Raspberry Pi? It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay so it is slightly larger than the Raspberry Pi board, which is perfect to cover it. The plate uses a high-speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video, etc. Best of all it plugs right on top nicely covering the Raspberry Pi board. Single power from Raspberry Pi is sufficient to operate the screen. As it uses the SPI and Power pin from Raspberry Pi"s GPIO, it is nicely stacked on the RPi board. We also carry the perfect case/enclosure for Raspberry Pi 3B/3B+ and also 4B to be used with this LCD.

3.5 inch RPi LCD V3.0 HVGA 480X320. There is a XPT2046, 74HC04D, 74HC4040D, and 2 74HC4094D chips on the back. Is there a way to determine which driver I need to use in software?

I am not 100% convinced that the distribution given works with the LCD (the item I bought is dis-continued but the seller provided another item that has identical specifications - 3.5" IPS 15fps 480x320 resolution - but I suspect it has a slightly, or altogether different, controller.

[*]Is there any way I can extract some information of what driver has been used, or tried to use, for the TFT via that half working distribution? As far as I know, a GPIO/ SPI connection will not gather connected hardware information...

I am not 100% convinced that the distribution given works with the LCD (the item I bought is dis-continued but the seller provided another item that has identical specifications - 3.5" IPS 15fps 480x320 resolution - but I suspect it has a slightly, or altogether different, controller.

[*]Is there any way I can extract some information of what driver has been used, or tried to use, for the TFT via that half working distribution? As far as I know, a GPIO/ SPI connection will not gather connected hardware information...

I bought a display off Amazon described as [ SainSmart 3.5" inch TFT LCD 240x320 RGB Pixels Touch Screen Display Monitor For Raspberry Pi for Model B & B+] and sold by: Sain Store. What I received is the 320x480 display you described. I am also trying to verify the model before I try to set it up.

It was working but was a bit too slow so, I Increased the speed After setting Everything back to normal the screen is not working properly. The display is fine , but the touch is not responding. Please help! Did I BROKE it ?

While googling for any info about lcd controller I came across this page: http://heikki.virekunnas.fi/2015/raspberry-pi-tft/, author managed to get from manufacturer patch file for kernel sources and tested it with 4.1.y - on which lcd worked. But still LCD replace HDMI, but I want to use this screen as additional for user interaction, while the bigger on HDMI as presentation monitor.

Since, fbtft has been merged with rpi kernel, so the fb drivers (including ili9341.c) was moved to fbtft_device driver (so the author of page can"t compile latest kernel with driver+patch).

So something about hardware, which I reverse engineered by the "hard way" - "grab multimeter and run through all LCD FPC pins and shift register pins"

I"m pretty sure about D/C (Pin 37 on LCD) and Reset (Pin 19 on LCD) pins by looking into driver code, but I can"t identify other signals (WR/RD/CS/etc...)

[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0x2938b030 smsc95xx.macaddr=B8:27:EB:38:B0:30 bcm2708_fb.fbswap=1 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait

- Controller is not ILI9341/ILI9325 - those are for smaller displays (320x240, etc...), I guess this might be ILI9486/9488 because they are for 480x320 displays. But when I compared init with DS it does not fit right so LCD can have a clone of ILI9486/9488 ...

- Module use only SPI interface and two CE signals (CE0 for touch controller, CE1 for LCD shift registers - compared to others lcd modules, in KeDei module this is swapped),

3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

This small 3.5-inch touch screen module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi. The screen also comes with a stylus to interact with the small screen.

Would you like the SPI kernel module to be loaded by default? YESS! thats what we wanted. Once done, exit the configuration menu and type in terminal command ‘sudo reboot‘; for the changes to take effect.Note:This method is applicable, only with the Raspbian version released after 1-31-2015.

Now we will have to configure the fbturbo video driverso as to change the video out from HDMI bus to SPI bus. For that, enter the following command in the terminal window:

After system reboot there wont be any output on the HDMI screen. So, to enter the further commands in the terminal we will have to use SSH method for remote connection to the Raspberry Pi board. Click here to see the steps on how to setup a remote connection.

Currently, the module for Raspberry Pi’s Broadcom processor snd-bcm2835 is set to load automatically. Add this code below the snd-bcm2835 line to support fbtft_device:

This 3.5-inch touch screen is the same size as the standard Raspberry Pi model B/B+, and well mates with the Raspberry Pi boards. With its touch screen and split audio from the HDMI input, it is ideal for portable devices and multimedia projects, and it is a replacement for a heavy and bulky HDMI monitor, keyboard and mice.