tft display microchip price

ER-TFTM050-3 is 800x480 dots 5" color tft lcd module display with RA8875 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 6800 8-bit,16-bit parallel,3-wire,4-wire,I2C serial spi interface. Built-in MicroSD card slot. It"s optional for 4-wire resistive touch panel (IC RA8875 built-in touch controller),capacitive touch panel with controller,font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable.Mounting on board by default. There is no capacitive touch panel connection on the board of ER-TFTM050-3,its capacitive touch panel needs to be connected with your external board.Now we design another new board with capacitive touch connection named_ER-TFTM050A2-3.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for5" TFT capacitive touch shield with libraries,examples,schematic diagram for Arduino Due,Mega 2560 and Uno. For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

ER-TFTM070-7 is 800x480 Pixels 7 inch color tft lcd display module with LT7683 controller board,superior display quality and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

This Bridgetek/FTDI EVE development kit includes a 5" EVE display module with a large bezel. This kit is perfect for demonstrating the EVE module (CFAF800480E2-050SC-A2) or the base display (CFAF800480E2-050SC), simply plug the included Seeeduino to a 5v power source!

The included display is sunlight-readable, has extremely wide viewing angles, large color depth, and the touchscreen glass extends past the edge of the display for smooth mounting.

With the endorsement of our masterly professionals, we are engaged in offeringColour TFT Display that is available with a built in controller and memory and requires minimum 3 port lines to interface. Our offered TFT display is widely used in the electronic appliances like computer monitors, television sets, hand held video game systems, mobile phones, etc. High on demand in the market, our offered TFT display provides easy interface and operates on low current as well. Our esteemed clients can avail this display from us at the most reasonable price.

The backpack itself is a PCB which mounts on the back of a common LCD display making a two layer "sandwich". The complete assembly is designed to plug into a solderless breadboard where any interface components can be tested. Then, when the design is complete, the interface circuit can be transferred to a custom PCB or strip board which can be mounted on the back of the Micromite LCD Backpack making a three layer sandwich.

Basic Specifications are:Colour TFT LCD 320x240 pixels, 65536 colours. 2.8" diagonal measurement. Touch sensitive screen with the coordinates reported in pixels.

This 5V supply is used by the LCD display panel and dropped to 3.3V by IC2 for the Micromite. There is a third power supply of 1.8V inside the Micromite which is used to power the 32 bit CPU. The 47µF capacitor on pin 20 of the microcontroller is used to filter this power supply. The capacitor used here must be a tantalum or ceramic type. Do not us an electrolytic as that may prevent the CPU from starting.

The LCD display panel can be easily found on eBay by searching for "ILI9341" which is the name of the controller used in the LCD panel. These come in a number of different sizes however the Backpack PCB is designed to match the mounting holes of the 2.8" version. The Micromite will also work with other sizes of the ILI9341 display but you will have to invent an alternate mounting arrangement

There are many versions of the ILI9341 display on offer but the panel that you purchase should look like the one illustrated on the right. This is important, do not purchase anything else as it may not work with the Micromite!

The PIC32 microcontroller (IC1) can be found in many places. Microchip Direct sell the blank microcontroller for US$4.03 (for a single chip). Other suppliers such as Element 14, RS Components, etc also sell the blank chips at a slightly higher cost. Note that you do not need to purchase the PIC32 pre-programmed because using the Microbridge (the

The author would like to very much thank Peter Mather (matherp on The Back Shed forum) for demonstrating that the Micromite can drive a variety of LCD display panels and then developing the ILI9341 driver.

The ILI9341 TFT module contains a display controller with the same name: ILI9341. It’s a color display that uses SPI interface protocol and requires 4 or 5 control pins, it’s low cost and easy to use.

The resolution of this TFT display is 240 x 320 pixel which means it has total of 76800 pixels. This module works with 3.3V only and it doesn’t support 5V (not 5V tolerant).

The ILI9341 TFT display board which is shown in project circuit diagram has 14 pins, the first 9 pins are for the display and the other 5 pins are for the touch module.

So, the display pins are numbered from 1 to 9 (from left to right): VCC (5V), GND (ground), CS (chip select), RST (reset), DC (or D/C: data/command), MOSI (or SDI), SCK (clock), BL (back light LED) and MISO (or SDO).

As mentioned above, the ILI9341 TFT display controller works with 3.3V only (power supply and control lines). The display module is supplied with 5V where GND pin is connected to circuit ground, VCC and BL pins are connected to circuit +5V. This module has a built-in 3.3V regulator which supplies the display controller with 3.3V from the 5V source.

All PIC18F46K22 MCU output pins are 5V, connecting a 5V pin directly to the ILI9341 display board may damage its controller circuit. To avoid that, I used voltage divider for each line which means there are 5 voltage dividers. Each voltage divider consists of 2.2k and 3.3k resistors, this drops the 5V into 3V which is sufficient.

Interfacing PIC18F46K22 MCU with ILI9341 TFT display C code:The following C code is for mikroC PRO for PIC compiler, it was tested with version 7.6.0.

The default connection setting of the mikroC ILI9341 TFT library is hardware SPI1 module (SPI1 module must be initialized before initiating the display). Instead of hardware SPI1 module, software SPI or hardware SPI2 module can be used.

If TFT data pin (TFT_SDI) and clock pin (TFT_SCK) are defined in the main code (before #include “ILI9341.c”) then the library will automatically use software SPI.

As mentioned above, the ILI9341 TFT is connected to PIC18F46K22 microcontroller SPI1 module pins (SCK1 and SDO1). Hardware SPI1 module and the ILI9341 TFT display are initialized as: