3.5 inch tft display 320x480 in stock

ER-TFTM035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller and breakout board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in microSD card slot, optional 3.5" 4-wire resistive touch panel with controller XPT2046 and capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

Customers in many different industries have chosen this full color graphic TFT display module for its stunning 320x480 pixel 3.5-inch diagonal active area.

This TFT display is big (3.5" diagonal) bright and colorful! 480x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display.

This display has a controller built into it with RAM buffering so that almost no work is done by the microcontroller. The display can be used in two modes: 8-bit or SPI. For 8-bit mode, you"ll need 8 digital data lines and 4 or 5 digital control lines to read and write to the display (12 lines total). SPI mode requires only 5 pins total (SPI data in, data out, clock, select, and d/c) but is slower than 8-bit mode.

The LCD is available in 320 x 240 RGB and 320 x 480 RGB resolutions. And use CortexM4 CPU TFT driver, TFT driver IC support 65536 colors, The 3.5 inch TFT display can also support UART port (RS232 / RS485 / TTL), integrated real-time clock RTC, touch buzzer sound function, support 90 degrees, 180 degrees,270-degree screen rotation, 8-channel curve trend chart memory, standard 128Mb. We offer a 3.5-inch resistive touch screen and a 3.5-inch capacitive touch screen.

We also offer the case of a 3.5 “LCD screen monitor, click to see the detailed size dimensions of 3.5” TFT LCD screen. You can also check out Arduino projects with a 3.5-inch LCD display module on our blog. Can bring more ideas to your project.

3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

Alibaba.com offers 18990 3.5 inch screen products. About 19% % of these are lcd modules, 4%% are digital signage and displays, and 1%% are lcd monitors.

A wide variety of 3.5 inch screen options are available to you, You can also choose from original manufacturer, odm and agency 3.5 inch screen,As well as from tft, ips, and standard.

If none of these part numbers meet your requirements in terms of brightness, interface, or connection method, please email us at info@orientdisplay.com.

The control and driving circuit of TFT modules is low voltage and FRIDA micro-power CMOS circuit, can be easily damaged by static, static damage is an irreparable damage, and sometimes humans have hundreds of volts of high voltage static electricity, therefore, in handling, assembling and use should be extremely careful to prevent static electricity:

It is the cutest display for the Raspberry Pi. It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay. It"s designed to fit nicely not only to the Pi Model A or B but also works perfectly fine with the Model B+/2B/3B/4B.

Product Features: Cool Fan Design Cooling fan with aluminium bracket installed and thermal silicon pad for cooling the chip to keep your pi computer and screen cool always. It"s realize that 3.5-inch screen and fan can be used at the same time

After execution, the system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally. " 90 " can be changed to 0, 90, 180 and 270, respectively representing rotation angles of 0 degrees, 90 degrees, 180 degrees, 270 degrees If the rotate.sh prompt cannot be found, use Method 1 to install the latest drivers