surface pro 3 lcd screen replacement made in china

Use a Surface Pro 3 screen replacement to fix up a tablet that is out of order. Stock up and stay prepared for quick and simple repairs in a shop when a client has an unresponsive Surface Pro 3. Each LCD touch screen replacement is easy to install and will work just as well as the original part. Put it in to provide high responsiveness and great image quality.

An LED backlight helps keep the Surface Pro 3 screen replacement nice and bright for easy viewing at any time of day. Each unit includes a digitizer assembly that is needed to detect each touch on the screen. When installed, the Surface Pro LCD screen and digitizer will allow the user to control every tablet function with their fingers. No other input device is needed.

Search for an LCD touch screen replacement at Alibaba.com and get great deals on bulk shipping. Some suppliers can alter the size and resolution, allowing the part to be used in other tablet models. Vendors always use protective packaging to keep the Surface Pro 3 screen repair hardware safe during transit. Inspectors carefully check each part to ensure it will fit properly and work without any issues after installation.

Get a faulty device back in working order with a Surface Pro 3 screen replacement from Alibaba.com. Make any work in an electronics store or a repair shop easy and cheap. Use several replacements to refurbish a shipment of tablets for resale in a store.

surface pro 3 lcd provide the touch interface in smartphones, which are vital for them to function. Alibaba.com stocks a stunning range of high-tech surface pro 3 lcd with vibrant color depictions. Truly crystal-clear displays of surface pro 3 lcd are available covering various brands and models such as the Samsung Galaxy Edge 2, OnePlus 7T, Samsung Galaxy C5, and many more.

surface pro 3 lcd are the most commonly used displays, as they produce great image quality while consuming low power. Rather than emitting light directly, they use back lights or reflectors to produce images, which allows for easy readability even under direct sunlight. surface pro 3 lcd are energy-efficient, and are comparatively safer to dispose of, than CRTs. surface pro 3 lcd are much more efficient when it comes to usage in battery-powered electronic equipment, due to their minimal power consumption.

Some other advantages of surface pro 3 lcd over the CRT counterparts are - sharper images, little to no heat emission, unaffected by magnetic fields, narrow frame borders, and extreme compactness, which make them very thin and light. Some types of surface pro 3 lcd are transmissive, reflective, and transflective displays. Transmissive displays provide better image quality in the presence of low or medium-light, while reflective displays work best in the presence of bright light. The third type of surface pro 3 lcd, transflective, combine the best features of both the other types and provide a well-balanced display.

Whether as an individual purchaser, supplier or wholesaler, browse for an extensive spectrum of surface pro 3 lcd at Alibaba.com if you don"t want to stretch a dollar yet find the best fit.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Okay, finally home and installed screen, screen installs great. Digitizer seems to be an incorrect driver/firmware issue. I will post images following this to explain the issue. it seems that with someone else who may have the know-how it could work. I don"t know much about hardware ID"s and how they work or may be able to be changed/edited

Unless i was given a faulty one, i"m going to have to finalize with the v0.5 will not work. The screen that came with it works great. the digitizer didn"t seem to be getting enough power or being completely acknowledged. system restores, driver replacements and new installs.. didn"t seem to show anything.

EBay is selling these screens for a more reasonable price now days, even shipped from the US. but make sure it is the exact same version and or part #

Guys if you a digitezer v1.1 surface pro 3 i can get those for you. Just need to pay $150 plus shipping.. you pay you shipping label sent to me . Thats all i had few friends working for MS or intel... i sell Mobo or i7 4770k $60 plus shipping brand new with sealed. Just let me know.. also i fix MS SURFACE PRO3 FOR 300 JUST DIGITEZER, LCD AND DIGI FOR $450

I talked with that seller and he said that the V0.5 will connect to the surface that takes v1.1, but only the lcd and home button were responsive. The touch screen and stylus wouldn"t work with it.

I also spoke to someone that tried the repair. Touchscreen will not work. We will all have to wait until the correct version is available. I will be on the lookout

I can"t get a straight answer from the people selling the replacement of .5,.3,.2,.1 as to why it wouldn"t work. I had him tell me the measurements and the details of the .5 and it should fit in the 1.1 but he just won"t sell me the .5 because mine was 1.1.

The bigest problem is that we deal with sales reps who sell without real product knowledge and their margins doubtfully allow for errors. For this reason they wont sell.

Option might be to get a digitizer from EB and have a tablet table with vacuum to try and fix like this? Tablet pc MSP3: place your Tablet pc on the machine plate, power the separator machine to produce heat to about 100 degree, using the high temperature to melt the glue between the touch screen and the LCD pannel, then use the Crowbar and wire to separate the LCD and the glass till they are completely separated. I think they are using UV glue on the digitizer also. But not sure. Anyone have any info on just replacing the digitizer and not the LCD and digitizer OEM combo?

Above i attached photos of the lcd/digi replacement. The lcd seems to work fine.. the digitizer just doesn"t seem to acknowledge touch/pen. I was curious if it would be feasible to take the portion other than the digitizer and swap it out but it doesn"t look like that would be an easy fix either.

We understand your request, however, the installation process of the SW & FW on the DSP-4196 can only be done with dedicated tools. These tools are only available to Microsoft and their authorized distributers/repair labs. We regret not being able to assist more on this matter.

BTW, I"m only attaching the screen to the tablet using plastic spring clamps instead of the 3M foam tape that"s used to glue the screen down--at least until I"m certain it"s not just a bad digitizer in the first place.

after trying the firmware update again I got "Surface Pro Touch Controller Firmware" code 10 or 14. So that is a dumb error. i"m thinking mine is faulty if he is getting some response at least... wish i would have sent it back already could have gotten some kind of refund.. i doubt i can this late in the game.

If i get time this weekend i will try to run this under ubuntu and install that kernel. I"m excited to the prospect.. Even if i could get partial touch working this could be a spare portable machine. It just isn"t worth much if it can"t at least get some touch working...

3) That the factory didnt put these in production for the !&&* of it. And as such there may be a windows device/ manufacturer that has the correct user installeable firmware/ drivers. Either for W7 or W8 or W8.1

I added a post previous to this with some ideas on procceeding prior to full install of Ubuntu. Unfortunately it was marked as spam. Basically i sugested trying to dl drivers for devices that existed pre W8. Also to look at firmware drivers for the Sony vaio Duo 11

Lucas. Please confirm you have -following the process detailed - achieved full functionality of the digitiser. Please also confirm if this is only on v0.5 or on version v1.0 also.

Be sure the supplier of the digitizer is credible and confirms it is a working replacement. The first 3 I bought were defective and thankfully I was able to return. Keep this in mind if you are running into trouble.

Hey just wanna throw this in also, I have a reputable supplier that has new OEM quality V0.1 and V1.1 for the surface pro 3 for $329.00 plus shipping and Original New/used for $280.00. The original is actually taken off of another device. Oh and the LCD only for $51.00.

I"ve bought about 5 v0.5 digitizers, only 1 worked normally but with "ghost touches". I had about 4 surface pro 3s to repair and all used v1.1 digitizers.

I"ve had no success with replacing the digitizers, although the cost that I paid for each LCD Digitizer combo had turned up to be close to the replacement cost microsoft charges! For most people you might be better off with paying microsoft because a dented case can make it troublesome to replace the LCD as well

I suspect anything before v1 is basically preproduction, the people selling v0.5s had dug them out of a bin somewhere and started selling it for a buck.

If anyone is still after a V1.1, the eBay link below goes to where I bought mine. It turned up fairly quick and works absolutely fine. I had ghost touches and some touch wasn"t working at first but after I ran the sony calibration tool (also linked) everything is fine. I got a Pro 3 1631 for free with a broken screen and was determined to get it working so it"s a total result for me :-)

All depends on how confident you are. Once you get the old screen off, it"s 20x easier than doing an iPad. Just get some good adhesive because 3m tape just comes off once the Surface gets warm :-/

Maybe but as said many on the market are in my brief experience faulty and given MS charge less for a recon unit than the screen itself why would you go to the trouble of buying from China or HK?

Basically the reason I went for the repair myself is because I run a business fixing phone and tablet screens. I hadn"t done a surface yet so thought I"d give it a go :) As for tape? I"ll have to get back to you as I"ve not found anything decent as yet :/

I"m also wondering whether V1.1 is compatible with older versions. Still no one tried? I get asked very often to repair Surface Pro 3 with broken screen and I always refuse them, but perhaps needlessly?

i am thinking of replacing my lcd and have found a couple on aliexpress and ebay as a complete (lcd and digitizer) set. but the thing that i am getting confused about is the version. how do i know what version i will need with out having to open the surfacepro 3 ? and check the existing lcd installed?

Or even as low as $120 if you don’t mind waiting for delivery from China. Someone posted about having problems with ones from China but I afraid that even the ones from the U.S. were made in China. I’ve replace mine twice and both worked fine. Both times from physical drops and not part failure.