sainsmart tft lcd library factory
Voltage type: 5v or 3v voltage input voltage，input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.
SainSmart 2.8" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller ILI9325, it"s a support 8/16bit data interface , easy to drive by many MCU like arduino families，STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is XPT2046 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.
Voltage type: 5v or 3v voltage input voltage，input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.
This is Sainsmart 2.4 inch TFT LCD module with the TFT LCD shield kit for arduino enthusiasts.It includes one piece of 2.4 inch TFT LCD display and a TFT LCD shield for Arduino MEGA2560 (R3).We will provided you the whole document including the example project of arduino due with the kit. We will supply you the technical support after your purchase.
Voltage type: 5v or 3v voltage input voltage,input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.(Click here)
It is 100% compatible with the normal MCU like ARM AVR PIC and 8051,especially on arduino family such as arduino due and arduino mega2560(R3).The module uses the LCD controller Chip SSD1963 with 5 inch LCD including the touchscreen.
SainSmart 2.8" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controllerILI9325, it"s a support 8/16bit data interface , easy to drive by many MCU like arduino families,STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC isXPT2046, and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.
Voltage type: 5v or 3v voltage input voltage,input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.(Click here)
This is Sainsmart 2.8 inch TFT LCD module with the TFT LCD shield kit For arduino enthusiasts.It includes one pcs of 2.8 inch TFT LCD display and a TFT LCD shield for arduino mega2560(R3).We will provided you the whole document including the example project of arduino mega2560(R3) with the kit. We will supply you the technical support after your purchase.
SainSmart 2.8" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller ILI9325, it"s a support 8/16bit data interface , easy to drive by many MCU like arduino families,STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is XPT2046 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.
Voltage type: 5v or 3v voltage input voltage,input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.
This is Sainsmart TFT LCD Extend shield for arduino mega2560(R3) .Using this shield can help you out of the bothers to use other cables. You just need to plug the module to arduino mega2560(R3) through this shield.
The following just shows how does the TFT LCD shield work with arduino Mega2560 R3 and 2.8 inch LCD display,but the package just includes the TFT LCD Extend shield and 2.8 Inch LCD display.The package does not include the arduino mega2560 R3.
2,The LCD is compatible for arduino due and mega2560(R3),but the Shield is just for the arduino mega2560(R3).If you need the LCD Extend shield for arduino Due,you need a similar shield which is also provided from our store.
It is 100% compatible with the normal MCU like ARM AVR PIC and 8051,especially on Arduino family such as Arduino Due and Arduino MEGA2560(R3).The module uses the LCD controller Chip SSD1963 with 7 inch LCD including the touchscreen.
LCD-specificed intialization code is provided, so that you can save time to optimize power control register and gamma curves for best display performance. We have test the provided code, it gives the best display performanace
This is SainSmart UNO R3 and 2.8 inch TFT LCD module with the TFT LCD shield kit For arduino enthusiasts.It includes one pcs of sainsmart UNO R3, one pcs of 2.8 inch TFT LCD display and a TFT LCD shield. We will provided you the whole document including the example project of arduino UNO(R3) with the kit. We will supply you the technical support after your purchase.
The SainSmart Uno R3 is a microcontroller board based on the ATmega328 . It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Sainsmart Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes.
SainSmart 2.8" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller ILI9325, it"s a support 8/16bit data interface , easy to drive by many MCU like arduino families,STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is XPT2046 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.
Voltage type: 5v or 3v voltage input voltage,input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.
This is SainSmart TFT LCD Extend shield for UNO(R3) .Using this shield can help you out of the bothers to use other cables. You just need to plug the module to arduino UNO(R3) through this shield.
If you connect the touch screen LCD with UNO R3, the touch screen function will be useless . If you want to use the touch function, please connect the LCD with Mega2560 (R3) or Due (R3).
2.The LCD is compatible for arduino family,but the Shield is just for the arduino UNO R3. If you need the LCD Extend shield for other arduinos, you need another shield which is also provided from our store.
LCD-specified initialization code is provided, so that you can save time to optimize power control register and gamma curves for best display performance. We have test the provided code, it gives the best display performanace
ER-TFTM032-3 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.
Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.
Over the past year, I"ve ordered 47 of these SainSmart LCD displays. For a while, they had a good thing going, but in the Autumn of 2015, they changed their manufacturing and have utterly messed up this device. The first six that I ordered in the Summer of 2015 worked perfectly. But of the 41 devices that I"ve ordered after the change, 40% have failed right out of the box... 6 won"t power up at all, 4 have screen flicker, 2 the touch doesn"t work, 1 the LCD pixels were misaligned and 1 had a cracked screen.
What happened? Besides utter lack of quality control (these displays were obviously never tested), SainSmart changed the LCD screen hardware. Instead of using the LCD screen that would fit properly on the TFT_320QVT PCB (see pictures), they chose a slightly thinner, narrower LCD screen that normally fits the TFT_320QDT PCB. (notice the one letter difference). The problem is that the new screen DOES NOT FIT properly into the pin holes on the PCB and has a nasty habit of falling off (see pics). They obviously realized this at the factory, and rather than re-ordering the correct screens, they just tried to force them to stay on with double sided tape. But that hasn"t worked well. Many of my screens had fallen off by the time I received them! But because I own a business that uses these things and I didn"t know at the time that I could find alternative suppliers for this part, my work-around was to glue them into the best position possible using a hot glue gun. What a pain!
Moral of the story: Don"t order any of these from SainSmart LCDs until they have accepted they have screwed this up and fixed this problem. I suspect they will comment on this review once that has happened and I"ll make modifications to this review to let you know when the problem is fixed. Until then, BUYER BEWARE. And, any other SainSmart product that includes this 3.2" is very likely going to include this same problem - including the shield + LCD and Mega2560 + shield + LCD.
That all said, when this thing works, it works really well. I am satisfied with resolution and the touch is responsive. I use it in the product that our company sells. Just don"t get it from Sainsmart - for now. There are alternative suppliers.
* The screen IC driver comes in two flavors out there: SSD1289 and ILI9341. They both work, but the software configuration is slightly different. So, either use one or the other - or expect to somehow auto-detect which one connect to your Mega2560 (not possible directly) and then code for both possibilities. As far as I can tell, the SSD1289 is being phased out for the now more common ILI9341. I"ve ordered this device from a number of sites, but unfortunately they often list the item as SSD1289, but it arrives as a ILI9341. If you are new to this, my advice is to go with the ILI9341 driver. The UTFT library was updated in the Summer of 2016 to accommodate this newer driver. Another reason to pass on this Sainsmart device is that it uses the SSD1289 driver. How can you tell the difference? The model for SSD1289 is TFT_320QVT and the model for ILI9341 is TFT_320QVT_9341. Unfortunately, ads for these devices often have the wrong model number displayed!
Can this be a fault in my wiring? (is it possible to connect the wires in such a way that this happens. Seems unlikely as there are no separate color connection pins on the tft unit)
In Part 1, we were able to obtain and display values from KX022-1020 accelerometer on the TFT LCD panel. In Part 2, we’ll show how to control the TFT monitor while reading the contents of the program!
As before, we’ll be usingSainSmart ST7735RTFT monitor. It’s a compact LCD display that can be used both with Arduino and Raspberry Pi. The monitor has a built-in microSD card slot, so it’s possible to store and load images, in addition to reading and writing data. In this tutorial, we will only try to display values on the TFT monitor.
Once you made the change, compile the unzipped “TFT 18” directory with zip again, add it as a library in Arduino (or Arduino Create) Add Library, or place it under the “libraries” directory in Arduino’s installed directory and load the library.
for (uint16_t x=0; x < tft.width; x+=6) { tft.drawRect(tft.width/2 -x/2, tft.height/2 -x/2 , x, x, color); } } void testfillrects(uint16_t color1, uint16_t color2) { tft.fillScreen(BLACK); for (uint16_t x=tft.width-1; x > 6; x-=6) {
for(uint16_tx=0;x
Next, let’s display the accelerometer values on the TFT monitor! In the case of the Sensor Evaluation Kit, basically, it’s not necessary to change the wiring on the TFT monitor side. All that is needed is to insert KX022-1020 accelerometer to the Sensor Shield.
for (uint16_t x=0; x < tft.width; x+=6) { tft.drawRect(tft.width/2 -x/2, tft.height/2 -x/2 , x, x, color); } } void testfillrects(uint16_t color1, uint16_t color2) { tft.fillScreen(BLACK); for (uint16_t x=tft.width-1; x > 6; x-=6) {
for(uint16_tx=0;x
This concludes the tutorial on how to display and graph accelerometer values using TFT LCD monitor! There are quite a few side projects we can consider developing. For example, we can combine this TFT monitor and Arduino Pro Mini to make a wristwatch featuring small games, etc. It is also possible to make a data logger using, for instance, different sensors from the Sensor Evaluation Kit.
The dfUTFTFork is a fork of the UTFT Library by Henning Karlsen. The original UTFT library is well written and works with a number of TFT drivers. The UFTF library has a number of limitations when creating fonts. For example, with the original UTFT library, all fonts MUST have a character width that is dividable by 8 (i.e. 8, 16, and 24 etc...). You have 2 choices to create fonts; 1, by hand or 2 with the online Font Maker, which converts an image into a font array. Both, are not easy to do and are time consuming.
So I set out to modify the UTFT library to with work with The Dot Factory. “The Dot Factory is a small, GPL, open source tool intended to generate the required C language information to store many fonts and images, as efficiently as possible, on a microcontroller”. Basicly, if you have the font installed on your window PC, you can create a Font to use with the UFTF library.
SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.
Note:The SD library only can be use in version arduino-00xx and the library only supports FAT16 fomatted SD card up to 2GB, so you need to fomat your SD card to FAT16. 4GB FAT16 fomatted SD card is tested not working. Long file names are not supported. Keep your file names compliant with 8.3 standard.
This is a very popular LCD Keypad shield for Arduino or Freeduino board. It includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Analog Pin 0 is used to read the push buttons. The LCD shield supports contrast adjustment and backlit on/off functions. It also expands analog pins for easy analog sensor reading and display.
The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys — select, up, right, down and left. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5 stage voltage divider.
Initializes the interface to the LCD screen, and specifies the dimensions (width and height) of the display. begin() needs to be called before any other LCD library commands.for example:
Where can I buy SainSmart 3.2" TFT LCD Display +FT LCD Adjustable Shield for Arduino UNO Mega2560 R3 (General) online at the best price in the Zambia?
desertcart is the best online shopping platform where you can buy SainSmart 3.2" TFT LCD Display +FT LCD Adjustable Shield for Arduino UNO Mega2560 R3 (General) from renowned brand(s). desertcart delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
desertcart ships the SainSmart 3.2" TFT LCD Display +FT LCD Adjustable Shield for Arduino UNO Mega2560 R3 (General) to and more cities in Zambia. Get unlimited free shipping in 164+ countries with desertcart Plus membership. We can deliver the SainSmart 3.2" TFT LCD Display +FT LCD Adjustable Shield for Arduino UNO Mega2560 R3 (General) speedily without the hassle of shipping, customs or duties.
Yes, it is absolutely safe to buy SainSmart 3.2" TFT LCD Display +FT LCD Adjustable Shield for Arduino UNO Mega2560 R3 (General) from desertcart, which is a 100% legitimate site operating in 164 countries. Since 2014, desertcart has been delivering a wide range of products to customers and fulfilling their desires. You will find several positive reviews by desertcart customers on portals like Trustpilot, etc. The website uses an HTTPS system to safeguard all customers and protect financial details and transactions done online. The company uses the latest upgraded technologies and software systems to ensure a fair and safe shopping experience for all customers. Your details are highly secure and guarded by the company using encryption and other latest softwares and technologies.
Ms.Josey 
Ms.Josey