russound kpl keypad with lcd display supplier

2023-01-03 12:32:11

The KPL Keypad controls a CAS44 or CAA66 multiroom system. Its five-character display aids in source selection, offering over 100 source labels to name your sources. The display also indicates volume and system status.

Easily adjust the bass, treble, balance, loudness and volume directly from the keypad to personalize the sound playback in any zone. For added convenience, you can turn the whole system off at any keypad.

russound kpl keypad with lcd display supplier

Russound"s KPSC is the perfect optional add-on keypad for a CAA66 multiroom system. It adds direct numeric selection and additional functionality, such as, play, pause, track up and down. The KPSC links to a KP6 or KPL keypad to fit neatly in a double-gang wall plate.

russound kpl keypad with lcd display supplier

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product"s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

6. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause the appliance and cart combination to overturn.

8. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

2. Do Not Touch The Unit With Wet Hands � Do not handle the unit or power cord when your hands are wet or damp. If water or any other liquid enters the cabinet, unplug the unit from power immediately and take it to a qualified service person for inspection.

4. Care � From time to time you should wipe off the front and side panels of the cabinet with a soft cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel lettering.

USER SECTION Product Introduction ............................................................................................................5 Component Guide CAA66 Controller ................................................................................................................6 KP6 Keypad........................................................................................................................7 KPL Keypad .......................................................................................................................8 KPSC Keypad......................................................................................................................9 Numeric Entry................................................................................................................9 Prefix and Suffix Commands ...........................................................................................9 SRC1 Remote Control........................................................................................................10 Operation KP6 User Options Mode ....................................................................................................11 KPL User Options Mode.....................................................................................................12

INSTALLER SECTION Getting Started Unpacking ........................................................................................................................13 System Components .........................................................................................................13 Tools Needed....................................................................................................................13 System Installation Considerations......................................................................................13 Connection Tips ................................................................................................................13 Wiring Instructions Keypad Wiring...................................................................................................................14 Speaker Wiring .................................................................................................................14 Component Guide CAA66 Controller Front Panel Removal ...............................................................................15 CAA66 Controller Rear Panel .............................................................................................16 KP6 Keypad Update Port ...................................................................................................17 KP6 Keypad Rear Panel ....................................................................................................18

Making Connections Keypad Port Connections...................................................................................................19 Source Audio Input Connections .........................................................................................20 Source IR Connections ......................................................................................................20 RNET Source Audio Connections ........................................................................................21

RNET Sources..........................................................................................................35 UEI Library ...............................................................................................................36 Learned IR ...............................................................................................................37 Invalid Code .............................................................................................................38 Clear Code ..............................................................................................................39 Source Setup Flow Chart ...............................................................................................40 KPL Setup Flow Chart ....................................................................................................41 KPL Diagnostics Flow Chart ...........................................................................................41

The CAA66 caters to homeowners who want more control over their multiroom systems with such capabilities as infrared (IR) tools to manage the system from anywhere in the house. More source inputs, simplified programming and user adjustable sound controls make listening to music throughout the home easier than ever.

The CAA66 kit ships with a remote control (SRC1) and elegant keypads (KPL or KP6 models) for home audio one-touch control. From each keypad, the user can adjust bass, treble, balance and volume. The system supports multiple keypads per zone for convenient access and includes an RS232 connection for integration with home automation systems.

Russound"s controller/amplifiers meet the needs of homeowners who want to experience true audio fidelity throughout the home. And with the CAA66, customers have more home audio choices at a cost-effective price.

The CAA66 front panel consists of a split molded piece with a removable bottom half. This bottom piece hides the Programming Center buttons. The power switch has a push on/push off action with a blue LED

6 IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. Also used when the keypad is operated using the CA System remote controls.

The KPSC keypad connects to a KP6 or KPL keypad to add source control and numeric capability. The amber backlit buttons provide primary source controls when pressed, such as stop, play, next, etc.

A second press of the Numeric button sends a Suffix command of "Enter" and puts the keypad back into the primary control mode. If the button is not pressed the second time, a 3-second time out will send the Suffix command and exit Numeric mode.

To enter the User Options Mode, press and hold the Source button when the zone is on. A press and hold of the Source button (or a 9-second timeout) returns the keypad to regular operation.

To enter the User Options mode, press and hold the Source button when the zone is on. Press and hold the Source button again (or a 9-second timeout) returns the keypad to regular operation.

The first option name (Bass) appears on the display to indicate it is ready for adjustment. Subsequent presses of the Source button toggle through Treble, Loudness, Balance, and Turn On Volume.

Once an option is selected, the Volume Up/Down buttons are used to adjust settings. The volume indicator bars indicate the option setting, along with setting numbers displayed on the LCD.

Unpacking the System Components � Keep the original carton and packing materials for future shipment or storage. � Check for any visible signs of damage. If you encounter any concealed damage, consult your Russound dealer before proceeding to install the unit. � Retain the sales receipt as it establishes the duration of the limited warranty and provides information for insurance purposes.

CAA66 System Components: � 1 (one) CAA66 Controller/Amplifier � 6 (six) KP6 or KPL Keypads � 1 (one) SRC1 System Remote Control � 6 (six) 845.1 Micro Emitters

Tools needed for installation: � Drill with a 1/2" x 6" drill bit � Keyhole saw � Flat head screwdriver (medium size) � Phillips Screwdriver (cordless recommended) � 110 punchdown tool (included) � Modular RJ-45 crimper and connectors � Pair of diagonal cutters or wire strippers � Stud finder � Steel wire fish tape � Cable staples � Single-gang electrical work boxes

� It is recommended that the CAA66 and the source equipment be plugged into a dedicated 20-amp circuit with an isolated ground. A power line conditioner can reduce interference problems caused by noise found in some electrical systems.

� To determine the amount of CAT-5 wire required for the system installation, first decide how many keypads will be used, then determine the distance between each intended keypad location to the planned CAA66 location. The maximum recommended wire run length is 250 feet for each KP6 or KPL keypad.

� Make sure that the entire wire path between keypads and CAA66 is clear and not obstructed by a floor ceiling joist, or masonry wall which can"t be drilled through.

The CAA66 front panel removable bottom half hides the Programming Center. It is important to follow the proper removal process to remove the panel without damage.

The KPSC 12-pin header and the update jumper for the KP6 (and KPL) are located on the right side of the keypad when facing front. These are covered when a trim plate is installed. Note: The update pins on the KP6 are accessed from the side when the keypad is not installed.

The KP6/KPL keypad uses a 110punchdown terminal on the back panel to provide simple installation and a strong connection for CAT-5 cable"s eight conductors. Punchdown terminals require the use of a punchdown tool. Attach the CAT-5 cable to the 110-punchdown terminal on the KP6 keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly

if the terminations deviate from the required connection order. Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Use of the impact tool may propel stray bits of wire and jacket into the keypad"s chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed into the junction box.

5. Mount the keypad in the electrical box. For the KP6 keypad, insert the source name labels in the appropriate slots before attaching the back plate and trim plate.

The Keypad Ports are located on the back of the CAA66 in the top left of center. Connections at the Keypad Ports are made with RJ45 connectors using T568A CAT-5 wire configuration.

For a clean installation when wiring from a Keypad Port, use an RJ45 CAT-5 patch cable to connect from the keypad port to an RJ-45 wall plate (optional). Using the same RJ45 T568A CAT-5 wiring configuration, use CAT-5 from the RJ45 wall plate to the keypad.

If using more than one keypad in a zone, use an SA-ZX3 System Keypad Splitter (optional). The SA-ZX3 supports up to three keypads per zone and connects directly to the Keypad Port for that zone. The CAT-5 for the keypads is run to a wall plate, with RJ45 CAT-5 patch cables between the wall plate and the SA-ZX3. Always use the RJ45 T568A CAT-5 wire configuration when connecting keypads.

Source Audio Connections The CAA66 supports up to six audio sources. The Source Inputs are located on the back panel. Connect each source using quality RCA signal cables. Connect the Left and Right Audio outputs from each source to the corresponding inputs on the CAA66 controller. Label each cable with the name of the selected source and the Source Audio input number located on the CAA66.

1. Using an IR emitter (the Russound 845.1 is recommended) attach the end of the emitter with the 1/8" plug to the IR emitter port above the source input.

RNET Source Audio Connections The CAA66 supports source control of Russound RNET components (ST2 Smart Tuner, SMS3 Smart Media Server) through the Controller Link ports via SRC1 remote control commands but provides no feedback to keypads.

Using quality RCA signal cables, connect the Left and Right Audio outputs from each RNET source to the corresponding inputs on the CAA66 controller. Label each cable with the name of the selected source and the Source Audio input number located on the CAA66.

Common IR Connections The Common IR jack on the rear of the CAA66 allows control of any source equipment without that source being selected on the keypad. The connection for the Com IR jack is made using an IR emitter with a 1/8"" plug or IR link cable.

The Russound 845.1 single IR emitter is recommended, or use an IR connecting block such as the Russound 857 which allows multiple units to be controlled through the COM IR Port.

The speakers are connected to the CAA66 using modular snap connectors. Each of these colorcoded connectors is designated for the speaker set of a particular amplified zone. To avoid confusion, connect one zone speaker set at a time starting with Zone 1, taking care to keep zone and speaker wire identities straight. Note: An 8 Ohm minimum speaker is required for each amplified output.

Zone Fixed/Variable Audio Output The CAA66 has two line Audio outputs, on Zone 1 and Zone 2. Each of these zone audio output connections features a stereo line out RCA connection plus a switch to allow for either a fixed or a variable line level output. When set to Variable, the keypad volume level affects this output. In the Fixed position, the keypad volume level will not change the output level.

The fixed or variable audio outputs can be used if additional amplification is desired (e.g., Russound R235LS two-channel amplifier). Use quality RCA signal cables to ensure a constant quality audio signal.

When 12VDC is applied to the Mute In, the system will fully mute all zones in the system. The connections for the trigger are made using a twoconductor cable with 1/8" male mini-plug jacks. The tip is positive (+) and sleeve is negative (-). This allows for the connection of an external paging or muting device. Note: The CAA66 will not accept a paging audio input; however, if used with an independent paging system with 12V trigger out, that can be used to trigger the mute.

Trigger Out 12VDC output is used for triggering an external amplifier or other component. The connections for the output are made using a two-conductor cable with 1/8" male mini-plug jacks at each end. The tip is positive (+) and sleeve is negative (-). The System Trigger Out supplies 12VDC when the first keypad is turned on. The 12 VDC is removed 5 minutes after the last keypad is turned off.

The Controller Link In and Link Out can be used to connect up to six CAA66 controllers. The connection is made using a CAT-5 patch cable from the Link Out of the master CAA66 and into the Link In of the next controller. Along with data signals, the Controller Link In and Link Out jack passes the six source IR signals. The CAT-5 patch cable should not exceed 18 inches in length to avoid potential cross-talk between the source-specific IR repeating signal lines.

The CAA66 supports RS-232 communication with various third party automation systems or PC for control and firmware updates of the controller. The RS-232 com port is located on the back of the CAA66 and uses a DB-9 cable connection.

For RS-232 protocol, firmware updates and the backup PC application, see the Document Center at www.russound.com. Look for the Technical Documents under Multi-source/Multizone products.

1. Connect the speaker wires from Zone #1 to the CAA66 Zone #1 speaker output connectors. 2. Connect a keypad (KP6, KPL) to Keypad Port #1 on the rear of the CAA66. 3. Connect a source to the Source #1 Input on the CAA66 using RCA Audio patch cables. 4. Plug an 845.1 IR emitter into the Source #1 IR Output Jack and adhere the emitter end to the source equipment"s IR window. 5. Plug in the main power cords for the CAA66 and the source. 6. Turn on the main power switch on the CAA66 and the source. 7. Manually command the source to provide audio or use the source remote control. 8. Press the power button on the KP6 or KPL keypad and select Source #1. 9. To be sure of proper placement of the IR emitter on the source component, aim the source remote control at the keypad for Source #1 and try to control the source. Adjust the emitter over the source"s IR receiver if necessary. Congratulations � you should now hear the source through the speakers in Zone #1. If there is no sound, follow these diagnostic steps: 1. Check the source to see that it is operating properly. 2. Check the RCA Audio cable connections from the source to the Source #1 Input on the CAA66. 3. Check the speaker connections and verify that they are correct and are connected to the Zone #1 speaker outputs. 4. Check to see that the keypad is connected to the Zone #1 Keypad Port and verify the CAT-5 is properly terminated at both ends. If none of these steps produce successful results, call Russound Tech Support for further assistance.

The CAA66 and its connected sources are configured through the Programming Center, located on the front of the CAA66 behind the removable lower panel. The LEDs are dual purpose with different colors to indicate different modes.

The CAA66 has two main programming modes: Controller Setup Mode and Source Setup Mode. The bottom row of functions are used in Controller Setup Mode (Ctrl ID, Num Src and Fact Init) and are accessed with a press and hold of the Setup button. The top row of functions are used in Source Setup Mode (Source/Test, Cmd/Type, Code/Key and

The KPL Setup menu is used to choose source names, check the version number and perform a Factory Initialization of the CAA66 controller. The menu is outlined in the diagram to the right.

To access the Setup Menu, press and release the Setup button on the right side of the keypad until "SrcNm" (source names) appears on the display. Press the Source button to toggle through the menu options, and use the Volume Up/Down buttons to scroll through the selections. Press the Power button to enter a selection.

To access the Diagnostics Menu, press and hold the Setup button on the right side of the keypad until "Diags" appears on the display. The menus are outlined in the diagram to the right.

Audio Access Cableshare Comfortex Da-Lite Elero Evergo GE Gewa Holmes Hunter Douglas Lightolier LiteTouch Lutron One For All RadioShack Russound Sanyo Security System Somfy Universal X10 X10

The Russound CAA66 is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor.

For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound. The unit must be returned to Russound at the owner"s expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damage resulting from abuse or from servicing by an agency or person not specifically authorized in writing by Russound.

Russound sells products only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product.

Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner"s expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit.

Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number. Write this number on the shipping label and ship to:

Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice.

The Russound CAA66 Multiroom Controller-Amplifier distributes six stereo audio sources to six zones. For larger installations, up to six CAA66 controllers can be linked together to accommodate a total of 36 zones.

For zone and source control, the CAA66 system offers a choice of two zone keypads plus an optional numeric source control keypad. The controller supports multiple keypads in each zone when using the optional SA-ZX3 Keypad Splitter.

The controller provides both source-specific and common IR output ports for device control. It can also link directly to Russound RNET� source components for control from the keypads; however, it does not support data feedback from the sources.

To enable easy integration with paging systems, home automation systems and other devices, the controller provides a muting trigger input and system trigger output, as well as an RS-232 port with a documented serial protocol. The RS-232 port can also be used to update the system firmware.

The CAA66 system keypads connect to the controller with CAT-5 or CAT-5e cable. The speakers connect to the built-in amplifiers with standard speaker cable.

Since 1967, innovation, quality and reliability have been the core of the Russound product tradition. Today, Russound offers everything for enjoying multiroom audio-video in your home. All audio-video distributed solutions are built to high standards and designed with the unique consideration of making products that are a pleasure to live with and enjoy.

� 2007 Russound. All rights reserved. All trademarks are the property of their respective owners. Specifications are subject to change without notice. Russound is not responsible for typographical errors or omissions.

The Russound KP6/4 is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor.

Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis or the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner"s expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit.

Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number. Write this number on the shipping label and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857

Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice.

The KP6/KP4 keypad is an in-wall Decora� style, single-gang keypad designed for individual zone control of CAA66/CAS44 distributed audio systems (wall plate not included). It has amber backlit, soft-touch volume, power and source select buttons. The KP6 keypad supports the KPSC keypad to add source control and numeric control capability.

5 IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. Also used when the keypad is operated using the CA System remote controls.

The KP6/KP4 OS update jumper and KPSC 12-pin header are located on the right side of the keypad (when facing front). These are covered when a trim plate is installed.

3 OS UPDATE PORT - Used to update the KP6/KP4 keypad operating system firmware. If an update is released, it will be available online through the Document Center on www.russound.com. Look in the "Firmware and Downloads" section under Multi-Zone product type. The Advanced Programming Cable is available from Russound, Part #2500-521065.

The KP6/KP4 keypad uses a 110-punchdown terminal on the back panel to provide a simple installation and strong connection for CAT-5 cable"s eight conductors. Punchdown terminals require the use of a punchdown tool. Attach the CAT-5 cable to the 110-punchdown terminal on the KP6/KP4 keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly if the terminations deviate from the required connection order.

Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Be sure to use the lowest setting. Use of the impact tool may propel stray bits of wire and jacket into the keypad"s chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed into the junction box.

Each keypad connects to a Keypad Port on the back of the controller (CAA66 controller shown below). Connections are made using CAT-5 cable with an RJ45 connector (wiring scheme shown below).

7. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

2. Do Not Touch The Unit With Wet Hands � Do not handle the unit when your hands are wet or damp. If water or any other liquid enters the unit"s cabinet, take it to a qualified service person for inspection.

3. Care � From time to time you should wipe off the front panel of the cabinet with a soft cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel lettering.

The USRC Remote Control is the complete solution for all of your remote control requirements. It is designed to operate source devices and all Russound and A-BUS audio systems via the system keypad or IR receivers. Pre-programmed to control Russound devices, the remote also features learning capabilities. The USRC is pre-programmed to control Russound and A-BUS devices.

russound kpl keypad with lcd display supplier

Extensive IR device codes and learning capabilities are built into the CAA66, making remote and keypad control of the system as simple as pressing a key. Each zone of the CAA66 supports up to three keypads with the SA-ZX3 Keypad Splitter.

Russound has system kits that include all the necessary components for a CAA66 system. For additional cost savings, the kits include a CAA66 Controller-Amplifier, six keypads (KP6 or KPL), a USRC remote and six IR emitters. For ease of installation, the controller can be rack mounted (with the provided rack ears). Keypads are available in five different colors, and fit perfectly in any Decora® plate.

For homeowners who want to extend the benefits of their Apple® iPod®, Russound makes it easy to connect an iPod to the CAA66 for sharing and enjoying music collections throughout the home.

russound kpl keypad with lcd display supplier

You Might Also Be Interested In