lcd screen vertical lines supplier

it was raining hard and i forgot to close the window where my sony 4k lcd tv was placed..we were watching a movie when i suddenly noticed two vertical straight lines on the screen.i immediately turned it off,put a fan at the back of the tv where it got wet..i turned it on again but the line was still there..went to sony store and the staff said i should probably replace the entire lcd ..but the cost is 80% the price of the whole tv which is quite expensive..is there any chance i could repair the lcd screen whitout having to replace it.

Whether they appear as thin or thick, black or white, in the center of your screen or along the border, vertical lines on a TV or computer screen certainly interfere with your viewing experience. Unfortunately, these lines may signify a severe technical problem that"s disrupting the signal between the unit"s processor and its liquid-crystal display, or LCD, screen.

The T-CON board, short for timing control board, is the part of an LCD screen that relays messages between the device"s processor -- it"s brain -- and the display itself. The T-CON board is responsible for synchronizing different parts of the screen with the information it receives from the processor. When the T-CON board fails, the timing between different parts of the board is disrupted, leading to errant lines, both horizontal and vertical, as well as pixelation. The only fix is to have the T-CON board replaced, which generally means replacing the whole LCD screen and usually the entire device with it.

TABs, or tape-automated bondings, are an integral part of any LCD monitor. These bondings digitize the information they receive from the processor and send it to the tiny transistors that create the electrical currents that ultimately affect which colors you see on screen. A TAB fault -- also called a TAB failure -- happens when these bondings are damaged or otherwise disconnected from the processor. When this happens, entire rows or columns of pixels go dark because they aren"t receiving any messages from the processor to create their colors. TABs can usually be reattached by a professional TV repair person but over time may become so loose and so repetitively problematic that they may need to be replaced entirely.

Short for low-voltage differential signaling, LVDS cable systems use twisted copper wires to carry high-performance data. This technology is more energy efficient than earlier electrical systems used in LCD products and can reduce the electricity costs to power the unit. However, when the copper wire that makes up the LVDS is compromised, through either a jolting impact or residual damage, it interferes with the signal it transports from the processor to the LCD screen. As with a T-CON board failure, this results in pixelation as well as vertical and horizontal lines on the screen.

While some vertical lines are the result of damage to your screen, other causes have nothing to do with you, your screen or even how you use it. Instead, the lines may be tied to the video source. Anything that interferes with an Internet, cable or satellite signal, such as an improperly aligned satellite dish or a frayed coaxial cable, has the potential to cause picture distortion, including but not limited to lines on the screen and pixel problems. Even the source itself can transmit images with lines on it; for example, a local TV news station that suffers signal interference during a live shot may broadcast images with lines, pixelation or ghosting.

Vertical lines appearing on LCD screen is very common. Whether the screen belongs to a laptop computer or desktop PC, mobile phone, or even a television, the fault is usually due to the ribbon cable and its connections.

A faulty ribbon cable can cause all sorts of havoc manifesting in bright vertical lines. Sometimes they can be coloured lines such as blue, green, grey, black, and red. The lines can appear thick or thin and on just one-half of the screen. Sometimes the fault will manifest as two vertical white lines. You can even get horizontal lines as well.

If you have lines appearing on the LCD screen, then the first simple thing to check is the seating of the ribbon cable that connects the display panel to the motherboard. Most of the time, the fault is with the poor connection made by the ribbon cable.

One of the most common problems with ribbon cables is oxidation of the contacts. It can happen either on the ribbon cable contacts or on the socket contacts. Manufacturers often use a mix of gold and copper for the electrical contacts, however, if they have not used enough gold, then oxidation occurs over time. This results in a working television or laptop screen suddenly exhibiting lines.

One of the most common faults with laptops is that the ribbon cable connecting to the LCD panel cracks. It typically fails near the hinge area due to flexing in that region, and over time, some of the tracks on the plastic cable breaks. I have seen these types of faults on many laptops. It does not matter whether it is a Lenovo, IBM, Acer, Samsung, Toshiba, or even a MacBook Pro!

This type of fault can also occur on LCD televisions; however, it tends to be on new units, where the box has received an impact during transit from the factory.

I used this same method of troubleshooting to repair an LCD television recently. Modern televisions have a video out socket, and if you feed the signal from that to another monitor, you can check for the quality of the video display. If the external monitor does not show lines, then you know for sure that it is a connection issue. Hence, this method of troubleshooting works for some of the modern televisions as well.

When half of the vertical interlace is missing showing a picture that is broken up vertically, the display appears with vertical lines. This is usually due to a cracked ribbon cable.

Generally, for laptops a replacement cable is always required due to it breaking near the hinge. I had this Dell laptop and replacing the LCD ribbon cable solved the problem. I managed to buy a replacement from Dell for a modest price £6.00. The laptop was just outside the warranty period; however, they still shipped out the cable free of charge. This is the reason why people buy Dell. In my experience Dell tend to stand by their customers and products, and their prices for replacement parts are realistic and down to earth.

I had this problem for really long, when i connect my raspberry pi to the display, it shows white lines. I reconnected the ribbon cables but on my raspberry pi 3b+ the small plastic holder is gone so I used a cardboard piece. Did I fry the display port?

I didn"t do "tvservice -s" but I did connect the Raspberry Pi 4 to the screen and the HDMI monitor, on the HDMI monitor there was a rainbow box and it didn"t boot up to the OS, and on there were still lines on the screen. I wasn"t able to access the terminal since I was stuck on the rainbow box but it would boot up normally without the LCD display attached.

With the boot time rainbow pattern on the hdmi screen, does the top left square change from red to magenta when you boot with the dsi panel connected?

With the boot time rainbow pattern on the hdmi screen, does the top left square change from red to magenta when you boot with the dsi panel connected?

With the boot time rainbow pattern on the hdmi screen, does the top left square change from red to magenta when you boot with the dsi panel connected?

With the boot time rainbow pattern on the hdmi screen, does the top left square change from red to magenta when you boot with the dsi panel connected?

This issue can be quite annoying and will only get worse over time. Most report a single vertical line appearing after about 4 years of moderate use. After this, the lines continue to appear until the screen is so obstructed it is useless. One can replace the screen with one of two compatible models without modification

Our repair involves using a specially designed PCB inline with the LVDS cable. This will adapt the signals and route them to the pinout of a standard 17″ laptop screen. These screens can often be purchased for less than $100.

For example, it could signal that the power supply is either failing or faulty. In other cases, it could mean you have not connected the HDMI cable well, or there is a poor connection between the processing board and the panel. But another cause could be the picture does not fit the screen exactly.

When you see black vertical lines on your TV screen, the first step is to identify the primary cause of the problem. Start by testing the picture, check your cable connections, and verify that your external devices are working well.

You can also try changing channels to determine whether the lines appear on all channels. Understand that lines on a TV screen can either be a hardware or software issue.

Ideally, aspect ratio, screen resolution, and horizontal or vertical scan frequencies are settings that affect picture display on most TVs. In this case, refer to the external device’s user manual to adjust the picture format settings.

Your TV software runs the device. An outdated software program can cause many problems like vertical lines, poor picture quality, or failure to install apps.

In some cases, a TV fails to process a combination of image settings you have provided. That can cause many picture errors, including flickering lines on TV. While you can go through all the settings one by one, consider resetting your device.

Sometimes vertical lines on an LCD display could mean a damaged T-Con board. The T-Con or timing control card controls the timing of pixels displayed on the screen. If your T-Con board is faulty, the only solution is to repair or replace it.

If you see Samsung TV vertical black lines on the screen, check whether the lines are permanent or moving. If they are moving, your input source is incorrect. Disconnect and reconnect the video cable or HDMI to check if it resolves the issue.

Thirdly, you may come across a problem with your Samsung Smart TV whereby colored lines appear on the edge of your TV screen. The lines may be black, white, or green along the top, bottom, or side of the screen.

The issue occurs when you have set the picture size of your TV to JustScan or Screen Fit. Samsung calls the lines an Overscan line. If your setting is JustScan, the picture resolution of specific programs will not fill the screen, thus causing the lines.

You can fix a TV screen with lines in different ways. For example, you can change channels to see if the lines appear on all changes, change the input source, check cable connections, or power-cycle your device.

So the screen is not the same as on the H750-DK. There might be an issue with how you set your display interface. Changing the dimensions only can be insufficient. Are you using an LTDC display or a DSI one ?

This issue can be quite annoying and will only get worse over time. Most report a single vertical line appearing after about 4 years of moderate use. After this, the lines continue to appear until the screen is so obstructed it is useless. One can replace the screen with one of two compatible models without modification

Our repair involves using a specially designed PCB inline with the LVDS cable. This will adapt the signals and route them to the pinout of a standard 17″ laptop screen. These screens can often be purchased for less than $100.

The appearance of static or flickering horizontal lines on a computer screen can be frustrating and inconvenient, but there are many steps you can take to try to fix your problem. This guide will walk you through various checks and fixes you can perform on your computer and its monitor to find out why the lines are appearing and what to do to make them disappear.

Horizontal lines on a computer monitor can be caused by overheating or physical damage to the monitor and connecting cables. Conflicts between the screen and selected screen resolution and refresh rate settings can also cause line problems, as can out-of-date device drivers and operating systems.

Try a different monitor. If possible, try connecting to a different monitor or screen. It can help you determine if the lines are caused by your computer’s screen or the computer itself.

Check your monitor while it’s disconnected. Keep your monitor powered on, unplug it from your computer, and look for any flickering or lines on its screen while it’s disconnected. If you see any kind of distortion, this means that your monitor is damaged.

Close and reopen your laptop. Close your laptop’s screen, wait a few seconds, and reopen it again slowly. Look to see when the lines begin to appear on the screen as you open the laptop. If the lines only occur at a certain angle, the cause is likely damaged wiring.

Check the monitor connection. Ensure all of the cables are securely connected, and watch for any improvements in screen image quality while you’re inspecting the cables. If you notice the image improves or worsens while touching the connecting cable, it may need replacement.

Remove magnets and electronics. If you have other electronics or magnetic devices near your computer, screen, or the connecting cables, move them somewhere else as they may interfere with the connection and cause the lines.

Reset your monitor to its factory settings. If you’re using an external monitor or screen, use its built-in settings, not your computer’s settings, to reset it to its factory settings. You can usually access these settings via a physical Settings or Menu button on the computer monitor itself.

To fix coloration and distortion on a computer screen, power the monitor on and off, restart the computer, and make sure the cable between the monitor and computer is connected securely. If you"re using a CRT screen, try degaussing the monitor. You can also try adjusting your video card"s quality settings and experimenting with your monitor"s adjustment buttons.

To fix screen burn on a monitor, also called "ghosting," try turning off your display, ideally for at least 48 hours. Also, try setting your screensaver to an all-white image and letting it run for a few hours. You can also try using the JScreenFix tool, which fixes stuck pixels.

- If the power cord is connected to a surge protector or power switch, remove the cord from that device and connect it directly to the outlet. This is for testing purposes. Removing such devices assists in determining if the light display or the white lines on the LCD are related to the device or the Brother machine.

big money for laptops they did not believe to be "B grade". I may not be the most experienced engineer, but if it were my job to R&D issues like this you could bet that this vertical line issue would not have happened. And although I had fun debugging this one, I was not happy with my findings (simple fix / expensive mistake)...