esp32 tft lcd arduino manufacturer

A beautiful 3.5” touchscreen display, based on ESP32-WROVER, with a built-in 2M pixel OV2640 camera, which makes it an ever perfect platform for your ESP32 projects.

Makerfabs ESP32 3.5” Touch with camera is absolutely open for makers, and besides, Makerfabs provide plenty of Demos to help the users on the usage. Have a try at this fantastic display in your next ESP32 project!~

This module is the 3.2” version of the ESP32 touchscreen display, based on ESP32-WROVER, with a built-in 2M pixel OV2640 camera. The LCD is 320x240 TFT, with driver is ILI9341, it uses SPI for communication with ESP32, the SPI main clock could be up to 60M~80M, make the display smooth enough for videos; and the camera OV2640 with pixel 2M, with this camera, you can make applications such as remote photography, face recognition…

While the camera not used, you can freely use all these pins with the breakout connectors, to connect the ESP32 display with sensors/ actuators, suitable for IoT applications.

The 3.5inch TFT LCD Module is based on ILI9481 LCD driver that includes Micro SD slot. This module gives nice picture quality and works well with Arduino Uno and Arduino Mega controllers. This kind of module is not a touch screen display. No...

This board works fine with TFT_eSPI when the ST7789 driver is selected. The pin settings are different and the RGB colour order is reversed compared to other boards so I have added an option to the TFT_eSPI library to set the colour order.

I have set the SPI rate to 80MHz and the ST7789 TFT seems to work perfectly at that clock speed, the higher clock frequency boosts the drawing speed (e.g. clear screen in 18ms as opposed to 33.3ms).

//#define ILI9488_DRIVER // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)

LCD, or Liquid Crystal Displays, are great choices for many applications. They aren’t that power-hungry, they are available in monochrome or full-color models, and they are available in all shapes and sizes.

Today we will see how to use this display with both an Arduino and an ESP32. We will also use a pair of them to make some rather spooky animated eyeballs!

Waveshare actually has several round LCD modules, I chose the 1.28-inch model as it was readily available on Amazon. You could probably perform the same experiments using a different module, although you may require a different driver.

This display can be used for the experiments we will be doing with the ESP32, as that is a 3.3-volt logic microcontroller. You would need to use a voltage level converter if you wanted to use one of these with an Arduino Uno.

The Arduino Uno is arguably the most common microcontroller on the planet, certainly for experiments it is. However, it is also quite old and compared to more modern devices its 16-MHz clock is pretty slow.

The Waveshare device comes with a cable for use with the display. Unfortunately, it only has female ends, which would be excellent for a Raspberry Pi (which is also supported) but not too handy for an Arduino Uno. I used short breadboard jumper wires to convert the ends into male ones suitable for the Arduino.

Open the Arduino folder. Inside you’ll find quite a few folders, one for each display size that Waveshare supports. As I’m using the 1.28-inch model, I selected theLCD_1inch28folder.

Once you do that, you can open your Arduino IDE and then navigate to that folder. Inside the folder, there is a sketch file namedLCD_1inch28.inowhich you will want to open.

When you open the sketch, you’ll be greeted by an error message in your Arduino IDE. The error is that two of the files included in the sketch contain unrecognized characters. The IDE offers the suggestion of fixing these with the “Fix Encoder & Reload” function (in the Tools menu), but that won’t work.

Unfortunately, Waveshare doesn’t offer documentation for this, but you can gather quite a bit of information by reading theLCD_Driver.cppfile, where the functions are somewhat documented.

Here is the hookup for the ESP32 and the GC9A01 display.  As with most ESP32 hookup diagrams, it is important to use the correct GPIO numbers instead of physical pins. The diagram shows the WROVER, so if you are using a different module you’ll need to consult its documentation to ensure that you hook it up properly.

The TFT_eSPI library is ideal for this, and several other, displays. You can install it through your Arduino IDE Library Manager, just search for “TFT_eSPI”.

In order to run this sketch, you’ll need to install another library. Install theTjpeg_DecoderLibrary from Library Manager. Once you do, the sketch will compile, and you can upload it to your ESP32.

The Animated Eyes sketch can be found within the sample files for the TFT_eSPI library, under the “generic” folder.  Assuming that you have wired up the second GC9A01 display, you’ll want to use theAnimated_Eyes_2sketch.

The GC9A01 LCD module is a 1.28-inch round display that is useful for instrumentation and other similar projects. Today we will learn how to use this display with an Arduino Uno and an ESP32.

Alibaba.com offers 483 arduino tft display products. About 66% % of these are lcd modules, 5%% are integrated circuits （old）, and 1%% are digital signage and displays.

Easy to Program - Includes complimentary GUI Software that makes programming fast and easy for engineers. This can reduce your project"s time and expense. The SCBRHMI 5 inch TFT LCD display module can easily create an intuitive touch interface by adding png/jpg/bmp/svg/gif image files as your background and defining functions by components. It"s easy even for beginners.

Lots of Powerful Upgrades - New Launch Intelligent 5 inch HMI resistive touch screen can be controlled by any MCU. This offers 1 G Hz Cortex A8 CPU driving device and 256 Flash memory for HMI projects. You also get RS232/TTL UART Interface and serial USB port. The module is compatible with 7/28V wide operation voltage. (This is an excellent choice for your Equipment Control Arduino, STM32, ESP8266, ESP32, UNO, Mega, Nano, Raspberry Pi and R3 projects.)

Clear, Detailed, Hi Res HD - Our Smart TFT LCD touchscreen offers excellent 800x480 high resolution with 4-wire resistance touch screen. Rich 262K (18bit) color for high color restore. Rectangular ratio 16:9 display format conversion. 70°/70°/50°/70° wide viewing angle, adjustable brightness（300 cd/m²) , TTF Font and contrast (500:1) offers you the ultimate project experience to accomplish more with improved results.

Ultimate LCD HMI module for Industry - SCBRHMI Intelligent TFT LCD display STWC050LT-02 is a customer favorite for a wide range of industrial and business applications. You get highest quality with the most usable functions. Often purchased for equipment in medical, beauty, engineering, industrial control, electric power, civil electronics, automation, traffic, GPS, new energy, and IOT applications.

The TFT display is a kind of LCD that is connected to each pixel using a transistor and it features low current consumption, high-quality, high-resolution and backlight. This 2.8-inch full color LCD has a narrow PCB display. The resolution is 320×280 pixels and it has a four-wire SPI interface and white backlight.

Makerfabs has launched a 3.5-inch TFT touchscreen display with built-in WiFi and Bluetooth connectivity through an ESP32-S3 dual-core Tensilica LX7 microcontroller clocked at 240 MHz with vector instructions for AI acceleration.

This display offers a 320×480 resolution through the ILI9488 LCD driver, uses a 16-bit parallel interface for communication with ESP32-S3 clocked at up to 20 Mhz making it suitable for smooth graphics user interface, and the company also claims it is smooth enough for video displays, but more on that later.

Espressif Systems ESP32-S3 dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration, 512KB RAM, 2.4 GHz WiFi 4 and Bluetooth 5.0 LE with support for long-range, up to 2Mbps data rate, mesh networking

Display – 3.5-inch color TFT LCD with 480×320 resolution, 16-bit parallel interface (ILI94988 driver), and capacitive touch panel (FT6263); backlight controller

The display can be programmed with the Arduino IDE. Sample code using the LovyanGFX library and EAGLE schematics and PCB layout can be found on Github. Makerfabs also designed an ESP32-S2 model that lacks Bluetooth connectivity, and the ESP32-S3 touchscreen display comes with more RAM and eMMC flash.

I was tipped about this display by Jon, a regular reader and commenter on CNX Software, who bought it, and said it works as advertised. The ESP32-S3 can really drive a high-speed display with a parallel LCD interface. However, it can’t stream video because there is no H.264 decoder, but it is great if you want a responsive GUI.

Makerfabs ESP32-S3 16-bit parallel capacitive touchscreen display is sold for $39.80 plus shipping, and the ESP32-S2 model is the same price with a resistive display, and there’s a capacitive display option for $4 more. As a side note, we previously wrote about another, smaller ESP32-S3 display, namely the LilyGO T-Display-S3, with a 1.9-inch display connected over a slower 8-bit parallel interface, and no touchscreen function that sells for around $17.

In this project, we will make few some interesting projects using ESP32 & 3.5″ TFT Touch Screen Display Camera. The customized board is manufacture by Makerfabs and has a combination of ESP32-WROVER chip + 3.5″ TFT Display + 2 MP OV2640 Camera + SD Card slot. With this cutomized board you can make plenty of ESP32 Based project.

But before you start doing these projects, you can read the previous article, i.e ESP32 Video Game. The ESP32 Video game is built using the same ESP32 TFT Touch Screen Display Camera.

This is a beautiful 3.5” touchscreen display, based on ESP32-WROVER chip, with a built-in 2M pixel OV2640 camera. The combination of all these gives a perfect platform for ESP32 Application like Video Games.

The TFT LCD driver is basically ILI9488 & has a dimension of 3.5″ with 320x480 screen resolution. The ILI9488 LCD uses SPI for communication with the ESP32 chip. The SPI main clock could be up to 60M~80M, make the display smooth enough for videos. The camera module on this board is an OV2640 Camera with a 2MP resolution.

with this camera, you can make applications such as remote photography, face recognition & security system projects. While the camera is not used, you can freely use all these pins with the breakout connectors. You can then connect the ESP32 display with sensors or modules & use it for any IoT applications. The ESP32 chip support Arduino or MicroPython programming

The board is having a micro SD-Card slot for attaching an external SD-Card. The SD Card can be used for storing files and images. There is a type C USB Port, basically a USB to UART converter for ESP32 programming. You can connect a Type-C data cable to the board & directly upload the code to the Board.

There are two versions of ESP32 3.5″ TFT Touch Screen with Camera. One is the Capacitive Type and the other the resistive type. You can use any of the display that you want. The purchase Link for both the display is given below.

You need to add ESP32 Board Package to the Arduino IDE. To do that Select “File>Preferences>settings>Additional Boards Manager URLs” to fill the link: https://dl.espressif.com/dl/package_esp32_index.json. After that download the ESP32 Package from Board Manager.

LovyanGFX Library is a library for LCD Graphics driver with touch for ESP32 and SAMD51. It supports the TFT Touch Screen Display like ILI9163, ILI9342, ILI9341, ILI9486, ILI9488, ST7735, ST7789, ST7796, SSD1351. Download and add this library to the Arduino IDE.

The ESP32 Touch Camera use ILI9488 TFT Touch Display, which comes with resistive or capacitive screens. It has an OV2640 camera and SD card slot. It can be used as a webcam or an electronic album or a digital camera.

But in this project, we will use the product as a Touch Screen Camera. You can take photos with an OV2640 camera and preview them in real-time on a TFT screen. And then, you can save photos to the SD card in BMP Format. The photos that were taken can be later viewed through the TFT screen.

Unzip the code folder and then open the camera.ino file. The Arduino IDE will open with so many different tabs. In the code part, you need to make little changes as per the type of Touch Screen. Makes changes in the following line of the code to select the touchscreen type, either it is resistive or capacitive.

Since the embedded board has the 3.5″ Capacitive/Resistive TFT Touch Screen LCD Based on ILI9488, you can use it for painting or drawing applications. You can use your hand or stylus (resistance screen) to draw on the screen.

Unzip the code folder and then open the touch_draw_v2.ino file. The Arduino IDE will open with so many different tabs. Select/Comment/Uncomment the Capacitive or Resistive type Touch Screen Display in the code. And then you can upload the code to the ESP32 Dev Board.

After you upload the code, the TFT Display will start displaying the Dashboard with color selection on the side. You can choose any color and start drawing anything that you want.

Apart from taking pictures and drawing, you can use this ESP32 Touchscreen Display as a Slide Show Viewer. For this choose few pictures with resolution 480x320 and rename them as number 1, 2, 3, 4, ……, n. The Picture should be in.bmp format. The jpeg and png formats are not supported.

Unzip the code folder and then open the SD2TFT.ino file. The Arduino IDE will open with so many different tabs. You can now compile the code & upload the code to the ESP32 Dev Board. Such a cool ESP32 TFT Touch Screen Projects.

You can make more ESP32 TFT Display Projects using the same module. Thus ESP32 Touch Camera can be used in many application from gaming to drawing or imaging.