mcufriend 2.8 tft lcd shield library for sale

I have bought "MCUFRIEND" 2.8 tft touch lcd and controller printed on it shows "ILI9338". Example given in this library are not working except for the basic one and it don"t even work with touch examples. After searching on google found out that "MCUFRIEND_kbv" library for debug. When i run "diagnose_tft_support" it shows following output. Also added "Read reg" after first output. Please Help !!!

Can this 2.8" elegoo display play video at all? I"m trying to make a unit that an older woman, in her 80"s can play a video on it, if I set it up correctly? This is for a really good cause, I desperately need help, this is super important. Helping elderly folks with modern technology is tough. But I really need it to be able to play a video off the SD card if possible. Any help would be super highly appreciated.ReplyUpvote

Hello,please post our code also ..the screen driver must be known and that info must be known in order to get these things to work correctly..you show your code and then the vid blurs..Someone needs to write a pdf teaching how ,what ,when and why concerning these screens I would gladly pay $10.00 and I am sure others would too.I have 3 different tftlcds only 1 works its for the mega and Bomer has a lib for it,I am really considering use of Nextion units from now on 4 pins easy programming but higher cost...also the small cell phone screens use spi mode and are real easy to set up and use

The program runs and nothing is displayed but a white screen. when I open the COM4 I see that when I hit the screen numbers appear to calibrate the screens position so it is registering but not showing up on the LCD. please help me before I pull all my hair out.1

I"m having issues getting this display to work on my Arduino 101 board with the libraries that are suggested - errors in compiling seem to indicate that the board type isn"t supported in the Adafruit_TFTLCD library. Here"s a representative error:

I finally got the touchscreen to work correct using your links to the libraries. Found out that this specific TFT display module uses pin 6 & 7 for touch sensor, instead of the standard 4 & 5.0

I never received a response on this, so went through the painful process of copying code from the video. It can be found here for others that might need it. Not that this has some minor changes, but is fully functional and I will continue to refine: https://github.com/siliconghost/Arduino_2.8in_TFT_wSD

There are many tutorials on Arduino shields for 2.4 inch TFT LCD displays. In this road test I apply different tutorials to check the performance and issues of this specific shield: AZ-Delivery 2.4 inch TFT LCD display with resistive 4-wire touchscreen and an integrated SD card reader.AZ-Delivery 2.4 inch TFT LCD display.

TFT LCD is a variant of a liquid-crystal display (LCD) that uses thin-film-transistor (TFT) technology. That improves image quality, better contrast and addressability.

Depends on the needs of your project. Arduino UNO processor frequency is low. With the Arduino UNO full-color TFT LCDs are suitable to display simple data and commands. The TFT controller used cannot switch internal display RAM, so you can"t use the double buffer technique for animations but still you can only re-draw small sections of screen.

This module consumes most of the resources available in Arduino UNO. This is not a limitation of the module itself. In return, using a parallel interface allows you to quickly update the image. If you want to take advantage of all its functionality (LCD + touch screen + SD card), only pins 0 and 1 (RX and TX, respectively) and pin 19 (A5) remain unused. If the SD card is not used, pins 10, 11, 12 and 13 are additionally available. With a suitable layout, some SPI devices could be connected even if the SD card is used.

The PCB silkscreen indicates the main function of each pin, the labels are easy to read, although it does not show labels for the touch screen pins:Pin 9 - Touch X+ / LCD_D1

The SD card reader is very well located between the USB connector and the power connector, it does not touch either of them as it happens in other lcd tft shield modules and it is easily accessible to insert and remove the SD cards.

You can directly use the shield with any arduino uno. In this case we are using an Arduino UNO that exposes all the pins both on the header and on the board. In such a way that you do not need another shield to access the pins not used by the screen

ShieldCompatible with Arduino. 5V compatible, can be used with 3.3V or 5V logic. On-board 3.3 V (300mA LDO controller). The design is very well thought out and fits Arduino UNO perfectly.

If you want to take advantage of all its functionality (LCD + touch screen + SD card), only pins 0 and 1 (RX and TX, respectively) and pin 19 (A5) remain unused. If the SD card is not used, pins 10, 11, 12 and 13 are additionally available. With a suitable layout, some SPI devices could be connected even if the SD card is used.

The ILI9341 which can control each pixel with a small number of pins. The shield connects ILI9341"s data pins 0-7 to Arduino digital pins 2-8 (allowing parallel communication, not SPI). ILI"s RESET goes to pin to Arduino analog pin A4.CS (chip select) to A3. RS (CD command/data) to A2. WR and RD to A1 and A0.

Includes a resistive 4-wire touchscreen (touchpad). The touch screen is attached on the surface of the display. Touch screen needs two analog inputs and two digital outputs. It connects through 4 wires, which share arduino pins 8, 9, A2, A3 with the ILI9341 driver. So you can"t write to LCD display and read the touch screen in the same time. I. Driver chip is XPT2046.

The resistive touch screen does not appear to appreciably affect the optical characteristics. Works properly, It takes a little pressure with the stylus for it to respond like in old mobile phones. You notice how it sinks into the screen when you press with the stylus. The stylus that comes with the module makes it easy to use if your interface design uses small controls. Some touch screen libraries offer better accuracy by specifying the resistance of the touch screen in the X direction. Resistance can be easily measured with a multimeter by connecting the test leads to the LCD_D1 - X + and LCD_DS X- terminals. Touch is sensitive to pressure.

The SD card reader works well. Accessing the SD card with the functions available in the SD library included in the IDE version used does not present any problem. SD cards are recognized and can be written or deleted.

A while ago I bought this 2.4"" Inch TFT LCD Touch Display Shield for Arduino UNO, but only recently I came up with a project where I could make use of this piece of hardware.

It turned out that indeed the RGB packing function from the Adafruit library did not play well with that display, but shifting and OR"ing the bits only slightly different would do the trick.

Then, instead of calling the method tft.clor565, a call to the newly created function fixed_color565 made sure that images got displayed correctly from now on..

Normally we show example of real-time reading things like DHT11 on monochrome LCD displays. We can graph that information. Graphing With Arduino on TFT LCD Color Display Probably a Needed Matter to Many Users. Graphing Can Become Difficult On Display With Less Known Drivers. Previously we have talked around MCUFRIEND TFT LCD Calculator. That one had problem with working codes. There are worse displays which are sold. Worse in the sense – most of the Arduino users need some easy working library which works with most common matters. This guide discuss some of the basic matters for the displays which use Elegoo Libraries (Adafruit Industries) and MCUFRIEND TFT LCD. The logic will be same for all similar displays but some tweaks needed for the others to make graph in proper orientation.

There are 3 main matters in the coding part – setting up graphing, reading value like temperature from DHT11 sensor, draw the graph. Unfortunately for practical purpose, you need to use board like Arduino Mega. Connecting DH11 with Arduino UNO is difficult as it occupies the whole board covering all pins. We are not always using the card reader but essentially it is difficult use the unused pins on Arduino UNO with such shield display.

Basically I purchased one Elegoo 2.8′ TFT LCD and was searching for graphing for some other reason. You can directly open this link to use in Arduino Web Editor. To use the same code on other boards, you need to modify some parts like :

In next article, we will see how we can graph values read by LDR on MCUFRIEND display. That is hopefully will be simple. Although with my model of MCUFRIEND TFT LCD, it not going to be easy to make it properly oriented.

Hi, the schematic of this display is similar to mine and shows at header JP3 the Arduino Uno power header. Do you know if this 3.3V on this TFT shield/board is actual used. In the schematic it is shown as a label but is not connected to any one. It can not be connected to schematic internal 3.3V coming form the regulator because this would mean a short cut between two power sources. My feeling is that is and auxiliary power source for a non installed chip that I have on my board. Since that chip is not installed it looks like its not needed.

I ask this because I want to use this TFT with a Arduino nano which doesn’t have much 3.3v power on that pin. If it is used i need to implement and extra 3.3V regulator, if not its not needed.

I have one of these TFT LCD shields, but mine is a ILI9335. It has taken me nearly 2 weeks to find a working Library and code for my 9335 driver and I am now setting about creating sketches based around my working Library.

Unfortunately most sellers of these shields (excluding good reputable companies) do not adivise of which Driver is onboard the shield and it becomes difficult to locate a working Library for the driver of the purchased shield.

If there is no Library specific to your 6767 Driver (and I must say I have not seen one in my searches for the 9335 Driver) then you may have to download as many different Libraries to locate a sketch that works for yours.

there are (now) a lot of 2.8" TFT Pi designs out there. I believe mine was the first, and has been around in one form or another for over a year now. I offer full support on this forum, and here is the support thread :

Hey guys, its Nick again, welcome to educ8s.tv a channel that is all about DIY electronics projects with Arduino, Raspberry Pi, ESP8266 and other popular boards. Today we are going to take a look at how to use the inexpensive, ILI9325 driver based, 2.8” touchscreen display designed for Arduino and at the end of this tutorial, you should be able to determine ifthis Touch Screen is a good option for your Arduino projects.

The display comes as a shield which makes the connection with Arduino extremely easy, thus all that needs to be done for this project is to plug the display into the Arduino board since we won’t be adding any other sensor or actuator.

One of the few downsides to this display is that it uses almost all of the digital and analog pins of the Arduino Uno which means when using this shield, we are left with only 2 digital pins and 1 analog pin for connections to other components that the project we are building might require.

Fortunately, this display works fine with the Arduino Mega, so when working on projects with more pin requirements and size is not really an issue, we can use the Arduino Mega instead of the Arduino Uno. Unfortunately, this display does not work with some other Arduino Uno form factor based boards like the Arduino Due or the Wemos D1 ESP8266 board due to pin compatibility and library Issues.

In order to use this Arduino Touch Screen easily, we will need three libraries. We will need a modified version of the Adafruit TFTLCD library, the familiar Adafruit GFX library, and the Touchscreen library. All these libraries can be downloaded by following the links below.

With the Libraries installed, we can test the display by trying out the examples which came with the libraries. Two favorite examples are the graphicstext example and the tftbmp example whose demonstration can be seen in the tutorial video.

Next, we declare the colors to be used with their hexadecimal values after which we create an object of the Adafruit TFTLCD library class indicating the variables used to represent the pins to which the screen is connected on the Arduino.

We start the function by initializing the serial monitor and the LCD, after which we set the orientation of the LCD and fill the screen with a black color to serve as the background.