raspberry pi lcd touch screen 10 quotation

All orders are processedwithin 24 hoursafter they are placed. Usually, we are able to ship orders the next day. Weekend orders are shipped on the following Monday. You will receive a shipping confirmation email from our system when the shipping information has been uploaded.

Generally, we will ship the orders with Free Shipping, without the minimum order amount requirement. You may check if the free shipping method is available to your country in the Delivery Area below.

As soon as your order is packed and shipped, you"ll receive a shipping confirmation email. You will then be able to track your order through the tracking link on the email. If you haven"t received an email yet, please reach out to us atservice@sunfounder.com, our sales staff will contact you ASAP.

* Delivery Time - These are the delivery estimates provided by our shipping partners and apply from point of dispatch, not from point of sale. Once your parcel leaves our warehouse, we cannot control any delays after that point.

Raspberry Pi OS provides touchscreen drivers with support for ten-finger touch and an on-screen keyboard, giving you full functionality without the need to connect a keyboard or mouse.

The 800 x 480 display connects to Raspberry Pi via an adapter board that handles power and signal conversion. Only two connections to your Raspberry Pi are required: power from the GPIO port, and a ribbon cable that connects to the DSI port on all Raspberry Pi computers except for the Raspberry Pi Zero line.

Patio swings with canopies can allow you to enjoy your swing under heavy sunshine or rain. raspberry pi 10 inch touch screen monitor available here are offered at some of the best bargains. Get wood porch swings in bulk to blend in different kinds of hotel lobbies, classic lounges, and homes. Wood porch swings are common for their use in homes and children"s playgrounds. The wood used is inflexible enough to hold different weights. Buy your ideal swing for the backyard now with amazing deals.

You can buy wholesale raspberry pi 10 inch touch screen monitor to make use of some very practical features. Standing porch swings are ideal and need no attachment to any external pole or support. They can be one-seater or multiple-seaters. In an unenclosed porch, there are swings available which can be attached to the ceiling. You can purchase other swing accessories here too. Canopy swings, gliders for the porch, outdoor patio swings, and other patio swing chairs can be purchased here with good bargains. Get outdoor patio swings with a canopy suitable for your needs.

The Alibaba.com website provides these raspberry pi 10 inch touch screen monitor at amazing deals. Hanging a porch swing can be simply done with front porch swings available here with good bargains just for you. Shop now to take advantage of these unique deals.

I"m using it to run a lighting and irrigation system for my house. The color graphical interface allows me to use BMP images of my house and yard for control screens, and its built into an enclosure set into the wall for a slick professional look. I even put an access from the backside of the wall for wiring it without having to remove the Pi or the touchscreen.

Great responsiveness, inexpensive, can"t beat 10-finger multi touch! The python demos are really neat, too. Only gripe is that the screen isn"t oleophobic, but for the price I"ll take it!

This was easy to install and it looks good. The Touchscreen is responsive and clear, but you might want to use a stylus. The only issue i had is finding a case for it. You"ll want to get one right away, unless you have a 3D printer to make one yourself. The screen is really thin, so I didn"t want to carry it around without some protection. Overall, it"s a great touchscreen, especially for the price, and I like that it is Raspi-branded.

I purchased 5 touchscreen. Two before and three in January. Touch and display quality is superb. After two-three month of use (no rough use; handled with care), display LCD and front touchpanel (black bezel) break apart. They both are connected using a thin double sided tape. I was planning to use in industrial environment but after such issue, I dropped my plan to use it in industrial environment.

Five of two displays are not in good condition. First display"s touch-panel and display LCD was break apart after two-three month. The second among five displays had another issue. Display LCD was mounted slightly right side of the touchpanel. Once you power-up display, it is easily be seen that LCD panel was a bit off-side. The other display"s screen guard having so many scratches on them which seems mishandling.

I got a couple of these for several RPi projects that Im developing and they are working amazingly well for the application. If these fit your application needs I wouldn"t hesitate to recommend them.

This screen worked right out of the box! Touch worked great with my new pi 3! However aside how fragile the (non functional) edges are, the only real issue I see is upon shutdown of the pi... The screen goes through a series of screen washes/whiteouts and never really shuts off.. I have to pull power to get it to turn off.. I"ve even tried usb/provided jumper wires.. And both results in the same thing. Not sure if this an issue per se, but it is bothersome.. I can just turn the unit off, I need to unplug it too..

I am using Raspberry Pi 3. The display came up with no problems. I am just waiting for the Smarti Pi Touch enclosure (pre-ordered after the Kickstarter project closed) before continuing to work with it.

Basically, it "does what it says on the tin". It"s bright, relatively responsive and has acceptable color. Haven"t played much with the touch screen part of it yet, but very pleased so far!

The only question(s) that I have are regarding what sort of additional processor power is inside the screen, and whether powering it from the micro-usb connection whilst also bridged from the RPi3 is an issue (it hasn"t hurt anything, yet!).

I WAS DISAPOINTED THAT THE UNIT DISPLAYS EVERYTHING UPSIDE DOWN. I HAD TO USE THE LCD_ROTATE=2 COMMAND IN CONFIG.TXT TO FIX IT. THE INITIAL BOOT IS STILL UPSIDE DOWN BUT I GUESS AFTER IT READ THE CONFIG.TXT, IT FLIPS. SHOULDN"T IT COME STANDARD RIGHT SIDE UP?

Hmmm, it should, and this isn"t an issue we"ve seen before. I would suggest getting in touch with our Tech Support team, they should be able to help you out.

With so many, phone and tablets that have hi res screens, this is disappointing. It does what it"s supposed to, but has a retro look. Non techy relatives are not impressed.

The must annoying feature is the bright white screen when it loses signal as the OS shuts down. The touch input is inconsistent as input. I was using the I2C for a device was not able to get it going on the alternate I2C, but fortunately the required clock and data are on the DSI cable ... wasted hours finding that out. An OLED display, higher res, and lower current draw would be really nice in the next version.

I forgot to check that this LCD touchscreen don"t have a case. Much better that you have a notification (e.g. recommending the user to purchase also a case) when purchasing this kind of product. But thank you for this product, I will purchase again soon.

The only minor drawback that everyone should be aware (which is to be expected, honestly) is that the display draws quite a noticeable amount of current. The SmartiPi case comes with an splitter USB cable for the power source, but if you expect to use that, be prepared with a (very) beefy power supply, else you"ll get the thunder icon on the screen all the time and a very reduced performance (Just discovered that the RPi3 reduces its own clock when power is low).

I currently power this with a separate 1.5Amp supply for the screen and a 2Amp supply for the RPi3 and everything works just nice. This totals to a whopping 3.5A, which may be overkill, but keep that in mind as a reference.

I am impressed with this screen, I also got the mating case (SmartPi Touch) and it assembled nicely. With the separate case, the included jumpers and cable are not needed. The PCB was already attached with the standoffs. The packaging was super! The screen is slightly larger than 7 inches. I measured it as 7 5/8" wide X 4 3/8 high with a diagonal measurement of 8 9/16.

This official Raspberry Pi 7" touchscreens now come with the display controller already connected and mounted to the back of the display. You still need to be careful pulling forward the small black tab ends that connect a ribbon cable to the RPi.

I bought the companion enclosure as well. This Touchscreen works exactly as described. I am very pleased with the display. I ended up using a mouse anyway as the icons (while clear are very tiny) and selection areas are a bit small for fat fingers.

I connected it to a Raspberry Pi 3 B running Stretch and it seems to be working perfectly. I had been previously driving a VGA monitor from HDMI through an adapter. The RPI 7" screen started up just fine without changing or installing anything with the OS.

I connected it to a Raspberry Pi 3 B running Stretch and it seems to be working perfectly. I had been previously driving a VGA monitor from HDMI through an adapter. The RPI 7" screen started up just fine without changing or installing anything with the OS.

Based on other comments here and looking at one of these at a maker space, I bought the smartipi touch case for this; it"s strongly constructed and works great. Only issue was that I"m using this with a model 3 B+, and that takes a different door on the back than comes with the case (this is being fixed by the smartipi folks, but I don"t know the logistics of getting their new cases into Sparkfun)

I have tried other touch screens for the Raspberry Pi. They had complicated assembly and were very difficult to get them to work. This unit was easy to install and get working, is very nice looking. I am very Happy with it.

Right out of the box it worked. Didn"t even have to do anything to the RPi (in fact, both were taken out of the box at the same time, connected, and worked on the first power up). Screen quality is good for price. Also ordered the "SmartPi Touch" case which holds everything together very nicely.

Ordered it, a Raspberry Pi 3 B+, and a power supply. (Had a mouse, keyboard, and uSD on hand.). It came a couple of days ago, and I put together yesterday. Had noticed in the documentation that there"s a micro USB power input, and a standard USB output. In the configuration where the power supply is plugged directly into the Pi and the LCD interface is powered via a USB cable plugged into one of the Pi"s USB ports to the LCD"s micro USB, the LCD won"t light up at all. When the power supply is plugged into the LCD controller board and the USB cable connects power to the Pi, I get "low voltage" warnings (yellow "lightning bold"). When I use the provided F/F jumpers, it works fine, but this will cause problems plugging in other "hats", as well as clearance problems. (In my application, separate power supplies would be a BIG PROBLEM.) BTW, I checked with two different USB cables, and got the same problems as well as when I tried an Adafruit 5.25V power supply. (I was about to try a second RPi3B+ when the original one stopped booting. Fortunately I had another that I"d been using as a "pass-around" sample at talks, and fortunately when I tried it, it still worked, so now the "dead" one will be passed around!) Also, it could prove really useful to know what size those mounting screws are in case they get lost! Ace Hardware recently opened a new store about half a mile from my house!

The screen is portable enough to take with you and the Pi will use it with no configuration change when it"s powered up. Used it to set up several Raspberry Pis in a remote lab. Touch screen is nice but bring along a keyboard if you have to do any setup work. One thing to make it better, replace the jumper wires with a ribbon cable connected to 1x5 and 2x2 pin headers.

I have a Raspberry Pi in each room of my home and they run a Kiosk interface for home automation, cameras and more. I"ve tried some cheaper ones and none have survived. (I"m hard on equipment) I haven"t managed to break one of these yet.

Got a PI3+, 7" touchscreen and SmartPI case for manufacture test. I put these together and booted the latest Raspbian. The LCD and touchscreen connect to the display connector using a short FPC cable. The display booted and the touch screen just worked out of the box. There were some nice but not well documented improvements. They provide a Y USB cable to power both the PI and the LCD. This is a cleaner solution than the jumper wires they provide.I"m not a big fan of using lego blocks in a industrial environment but the case went together easily and does a decent job of protecting the display and the PI. Some reported a inverted display issue but that seems to have been resolved.

A truly plug-and-play display for the Raspberry Pi. Does not steal any additional extension connector pins if you power it with a USB power supply and leaves the I2C1 interface available for other devices.

Big enough for somewhat squinting actual Raspberry PI development and computer work, but really shines for touch screen optimized large button control panels.

You can just install a Pi3 or 4 on the back, but with a 4 you really need some additional airflow. The SmartiPi Touch 2 enclosure works better. https://www.sparkfun.com/products/16302

It works fine, no glitches, no problems, no hair pulling moments. Once electrically connected to my RPi 3B+ it"s good to go. I run it with the "lite" version of the Raspberry Pi OS with only xorg drivers installed, no full desktop or windows manager, as part of an in-the-field project with a HQ camera attached. My only complaint is the ribbon cable could stand to be about 6 inches longer.

It works great, the colors are beautiful, and finger touch works fine. What I like most is that the Raspberry Pi GPIO pins are all still available - except for one +5v pin and one Ground pin. Both are redundant (i.e. others are available). So, this is not an issue at all. I also like that data connects to the Pi via the IPS ribbon cable. Another thing I like is that power connects to the Pi via two jumper wires. The Pi is fussy about its power supply voltage. So, the jumper wires are better because they are heavier gouge than a small PCB trace.

I connect a Pi v4 and put the whole thing in the SmartPI Touch 2 case from Sparkfun and now it looks pretty professional. Make sure you use a good power supply.

Where is the documentation? This thing is so poorly documented it"s almost a joke. The whole point of the RPi ecosystem is to enable Makers and learning about electronics, so why isn"t this fully documented?

I used this to build a portable utility/testing device for my company. It works fantastic with the SmartiPi Touch Pro Case on Amazon. The touchscreen functions great, only thing is you can"t register mousedown and mouseup events in Chromium (only click). Other than that it"s great!

I got it working the first try, easy to follow instructions. Trying to learn Kivy with Python for touch screen programming, That"s a lot more difficult.

It"s bright, clear, good color rendition. Touch input is responsive and accurate. Trivial to assemble and get going. Like the multiple power options. Would buy again.

The official Raspberry Pi 7” Touchscreen allows you to add touch inputs to your programs, creating a new way to interact with your projects. It also makes for a fantastic desktop screen for day-to-day use of your Raspberry Pi. Wrap it in one of our screen cases and take it anywhere – events, Raspberry Jams or even just your friends house for a coding evening!

For smaller projects, LCD and ePaper displays are a fun way to add a visual element to your projects. With simple code and wiring, they’re great for projects that require text, menus and navigation.

This is the 3.5inch display for raspberry pi, support HDMI input, refresh rate of 60FPS or more. It has a physical resolution 480x320, configurable software resolution up to 1920x1080.  It can be used as raspberry pi touchscreen with touch control function (need to install touch drive). It also can be used as a computer monitor, TV box, PSP and other standard HDMI output device (without touch function). The 3.5 inch display module is compatible and can be inserted directly into all versions of raspberry pi board (raspberry pi, 1 generation B and Zero, HDMI line).

The official 7” Touchscreen Monitor for Raspberry Pi gives users the ability to create all-in-one, integrated projects such as tablets, infotainment systems and embedded projects. The 800 x 480 display connects via an adapter board which handles power and signal conversion. Only two connections to the Pi are required; power from the Pi’s GPIO port and a ribbon cable that connects to the DSI port present on all Raspberry Pi’s. Touchscreen drivers with support for 10-finger touch and an on-screen keyboard will be integrated into the latest Raspbian OS for full functionality without a physical keyboard or mouse.Kit Contents:- 7” Touchscreen Display- Adapter Board- DSI Ribbon cable- 4 x stand-offs and screws (used to mount the adapter board and Raspberry Pi board to the back of the display-4 x jumper wires (used to connect the power from the Adapter Board and the GPIO pins on the Pi so the 2Amp power is shared across both units)Perspex layer frame in your choice of colour!* Compatible with Raspberry Pi 3 and Pi 4 only. Not compatible with Pi 400. *

"The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touch screen. The LCD is well mated with Pi board and interface with Pi via the high speed SPI port, and support console, X windows, displaying images or video etc. It also provides 4 press buttons for user defined functions.

Other Features3.2” inch TFT LCD screen, Mounted directly, no need of any extended shield, Resistive touch panel, 4 user defined press buttons, Well mate with Raspberry Pi Model B+ Board, FBTFT graphic library support, Both command console and X window support

I’m always on the hunt for good accessories to go with my Raspberry Pi. Finding a good screen for regular but intermittent use is not as easy as it seems. I don’t want a large computer monitor on my desk to only use it a few hours a week, but I don’t want something too small that I can’t use. And there are also different features and price ranges depending on the brand, quality, and other factors.

Anyway, in this article I’ll review a new challenger: the 10.1″ Touchscreen from EVICIV, that you can find on Amazon for less than $200. It’s an all-in-one monitor, meaning you can use it as a standard monitor or put your Raspberry Pi inside the case on the back to keep your desk cleaner (less cables).

The SunFounder 7″ Touchscreen: A traditional screen for the Raspberry Pi, which does not have a case and is smaller than the screen I tested today, but by much.

Anyway, let’s dive in the review. If you are looking for a new monitor for your Raspberry Pi, I will try to answer all your questions in this article.

Note: To be transparent, EVICIV sent me this product for free, to test it and write a review. But I’m free to share with you my honest opinion about it. Just know that I didn’t pay for it, which possibly can play a role in my impressions.

The 10.1″ Touchscreen from EVICIV is not a basic product, so it’s great for a Raspberry Pi or even for other devices. Here are the main features to take into consideration:

And obviously, there is the case behind the screen where you can embed your Raspberry Pi. It’s compatible with the Raspberry Pi 3 and 4. Two side panels are included to fit with your Raspberry ports on one side. The other side is reserved for the screen ports (HDMI, USB-C, power and audio jack).

I’m not saying it’s cheap and I understand that it might be too expensive for some of you, as it’s the same price as a computer screen. But it includes features that I think explain the price, like the touchscreen and the case for your Pi.

The tiny USB cable on the top left is for the touchscreen. You’ll plug the USB side on the Raspberry Pi and the other side inside the case. You can also solder the other cable if you prefer. We’ll talk about this later.

There are a few plugs to connect the Raspberry Pi output to the monitor (HDMI, Micro-HDMI, USB-C and Micro-USB). It’s a smart way to make the case compatible with Raspberry Pi 3 and 4. I’ll show you some pictures.

That’s it. So, you have the user manual to help you with the first steps. It’s in color and pretty well done. I would have loved something more straightforward, but I understand that there are several ways to use the screen, so it’s normal.

If you just want to use it as a screen for a Raspberry Pi or another device that you keep outside, you have nothing to do, just plug your device into the HDMI input, and it’s done. But if you want to put a Raspberry Pi inside, you’ll need to follow the instructions.

As a whole, the assembly is pretty good. The main difference with the RasPad is that you’ll use the Raspberry Pi ports directly (the RasPad uses a motherboard that you plug everything into, and this motherboard has external ports). Both systems have pros & cons, so it’s not a big deal.

The USB cable for the touchscreen that goes outside the case is not pretty, but you don’t really see it once the screen is on its stand. The alternative is to solder a cable on the GPIO pins. I’m not ready to leave my Raspberry Pi 3B+ inside this monitor forever, so I didn’t do it, but it’s possible.

So if you put a Raspberry Pi inside this monitor, that’s pretty definitive. You can’t change the SD card, and they want you to solder a cable to your Pi. It seems a great product for a dashboard, digital signage in retail, or something like that, but not really a good fit for someone like me that tests something new every day. Or at least I shouldn’t put my Raspberry Pi in it to just use it as a monitor.

Note: The audio jack of the Raspberry Pi is not connected to the jack output of the screen, but it works. I suppose the screen redirects the sound coming from the HDMI connection to the jack output.

So, we start to see two scenarios: either using it as a normal screen, with the HDMI input, or using it with a Raspberry Pi inside, to display something 24/24 or at least something where you never change the SD card and don’t need GPIO/camera.

The first thing you can do is to use it as a simple screen.You won’t lose time with the assembly, you can just plug your HDMI cable on the side, and you are reading to go.

Once plugged, the screen should switch automatically to display your Raspberry Pi operating system, but there is a menu on the screen that you can use to choose between three sources: HDMI-IN, HDMI-RPI, and USB-C.

That’s the button on the right of this picture. You’ll use the up and down arrows to choose the source you want. The button with an “M” is here to change the main settings like on any screen (luminosity, contrast, etc.).

The fan inside the case will run even if you don’t have a Raspberry Pi inside. You can unplug it if you want, but it’s on by default, so you have a bit of noise when you turn on the screen.

I think that it works pretty well. You have your Raspberry Pi outside, in another case (like the Argon Neo), with access to everything (GPIO, SD card, camera, etc.). I would just shut down the fan, and I’m fine with it. It’s a better solution for me than the SunFounder 7″ I tested previously, 10″ is a way better size for a screen.

The second case is to use it like a case(sorry …). No seriously, that’s the natural way to use it as it’s built for it. Put your Raspberry Pi on the back of the screen as explained in the assembly part, and you are ready to go:

Digital signage: This is the first thing that comes to mind, I just have no idea if a screen of that size can be useful. Maybe to take orders in a restaurant or do a satisfaction poll? You can use a tool like Screenly to do this.

A static tablet: I mostly use my iPad to watch videos. I could install Android on a Raspberry Pi and use this screen to watch any of the media services (Netflix, Prime videos, etc.).

Magic mirror: I already told you this in my RasPad 3 review, but you don’t really need a “mirror” to use the magic mirror software. I can see a screen like this as a great dashboard with your calendar, tasks and reminders (read my detailed article about it here).

As a whole, it’s a good product, I just think they missed some convenient features, or maybe I’m just not their ideal customer. Anyway, I will still continue to use this screen on a daily basis, as it’s the best one I have. The Sunfounder 7″ is too small for me, and the RasPad 3 has other issues that annoy me from time to time. I’ll just use it as an external screen and unplug the fan because I switch my SD cards (or Pi model) almost every day.

You alway use the same SD card and want a compact solution with a monobloc case/screen. Just one power cable and everything is set up. The fan noise is not an issue, or you don’t use it 24/24 and can unplug it.

You just want a good touchscreen, and will plug your Raspberry Pi (or another device) to the HDMI port. You can use the USB-C port for the touchscreen.

Not sure where to start?Understand everything about the Raspberry Pi, stop searching for help all the time, and finally enjoy completing your projects.

Master your Raspberry Pi in 30 daysDon’t want the basic stuff only? If you are looking for the best tips to become an expert on Raspberry Pi, this book is for you. Learn useful Linux skills and practice multiple projects with step-by-step guides.

If you just want to hang out with me and other Raspberry Pi fans, you can also join the community. I share exclusive tutorials and behind-the-scenes content there. Premium members can also visit the website without ads.